Tools

V-Twin - 16-1280 - Jims Cam Bearing Puller ToolDescriptionThe Jims cam bearing puller tool is used to remove the bearing from the crankshaft and is designed to do this with no slipping or binding. Fits:FLT 1999-2016FLST 1999-2017FXST 1999-2017FXD...

V-Twin - 16-1276 - Jims TC-88 Wrist Pin Remover ToolDescriptionJims wrist pin remover tool will cut the time it takes to remove and install wrist pins.This remover tool can be easily used by one person. ...

V-Twin - 16-1275 - Jims TC-88 Crankshaft Rear Bearing ToolDescriptionThis crankshaft bearing tool is designed to remove and repla ce the right crankcase bearing in and out with no damage to crankcase. Fits:FLT 1999-2016FLST 1999-2017FXST 1999-2017FXD...

V-Twin - 16-1274 - 4-Speed Transmission Arbor ToolDescriptionThis 4-speed transmission arbor tool is what you need to replace the clutch hub nut to allow test rotation with 1/2" drill. Fits:FX 1971-1984FL 1941-1984Additional Information UOM1 - EA ...

V-Twin - 16-1273 - TC Beta Engine StandDescriptionThe Beta engine stand is powder coated steel and clears the rear balancer housing of the Beta style TC case. Fits:FLT 1999-2016FLST 1999-2017FXST 1999-2017FXD 1999-2017Additional Information UOM1 - EA ...

V-Twin - 16-1271 - Cam Bearing Puller ToolDescriptionThis Sifton cam bearing puller tool removes the inner cam bearing, Torrington type without splitting cases while preventing rollers from coming out during the removal.Tool is designed for hand wrench...

V-Twin - 16-1270 - Rider Tool KitDescriptionRider tool kit fits into the included 7" x 2" blue zip-up pouch.17 piece tool kit. ...

V-Twin - 16-1267 - Rear Sprocket Rivet ToolDescriptionRear sprocket rivet tool will hold sprocket in place to install rivets by a hammer.This is a 5 piece set. Includes drum holder, drum collar, spacer (for Sportster drums only), rivet set and hollow...

V-Twin - 16-1264 - Motor Number Stamp SetDescriptionHardened steel stamps to restore motor numbers on early motors.Sold as a 22 piece set. Set has many variations of numbers, letters and shape combinations. Fits:FL 1948-1969EL 1948-1952Additional...

V-Twin - 16-1261 - Transmission Main Gear Nut WrenchDescriptionThis tool is used to remove the 2-1/4" hex nut from the main drive gear which secures the rear drive transmission pulley. To be used with 1/2" drive ratchet.This tool is designed to remove...

V-Twin - 16-1204 - Jims M8 FXST Engine StandDescriptionJims M8 FXST engine stand, needed for any powertrain work, is built from .125" steel and powdercoated blue. Fits:FLST 2018-UPFXST 2018-UPAdditional Information UOM1 - EA ManufacturerJims OriginUSA...

V-Twin - 16-1203 - Jims M8 Flywheel Locking ToolDescriptionJims M8 flywheel locking tool has an added o-ring to prevent oil seepage. This tool is designed to specifically locate and lock the flywheel in the engine and locks the crankshaft when doing...

V-Twin - 16-1202 - Jims XL Primary Locking BarDescriptionJims primary locking bar tool locks the primary drive on XL models to facilitate crankshaft sprocket nut removal and installation, along with clutch service.By shifting the transmission into top...

V-Twin - 16-1201 - Jims M8 Cylinder Torque Plate KitDescriptionThis Jims cylinder torque plate tool kit simulates stress conditions when boring and honing cylinders. For M8 models. Fits:FLT 2017-UPFXST 2018-UPAdditional Information UOM1 - KIT ...

V-Twin - 16-1200 - Jims M8 Left Main Seal Removal ToolDescriptionJims left main seal removal tool is for M8 models. Fits:FLT 2017-UPFXST 2018-UPAdditional Information UOM1 - EA ManufacturerJims OriginUSA 2025 Catalog Pages1274

V-Twin - 16-1199 - Jims M8 FLT Engine StandDescriptionJims M8 FLT engine stand, needed for any powertrain work, is built from .125" steel and powdercoated blue. Fits:FLT 2017-UPAdditional Information UOM1 - EA ManufacturerJims OriginUSA 2025 Catalog...

V-Twin - 16-1198 - Jims Fork Cap Installation ToolDescriptionJims fork cap installation tool for use on 49mm forks, allows the installation of the fork tube caps on the motorcycle without removing other parts Fits:FXD 2006-2017FLT 2014-UPAdditional...

V-Twin - 16-1197 - Jims Fork Cap Allen Socket ToolDescriptionJims fork cap large allen head socket tool for use on 49mm forks. Fits:FLT 2014-UPAdditional Information UOM1 - EA ManufacturerJims OriginUSA 2025 Catalog Pages1295

V-Twin - 16-1196 - Jims Steering Head Race Installer ToolDescriptionJims steering head race installer tool features smaller and tapered drivers, ensuring optimal alignment and a fully installed depth. Fits:FLT 2014-UPAdditional Information UOM1 - EA ...

V-Twin - 16-1195 - Jims Hollow Axle Installation Guide ToolDescriptionJims axle installation guide tool is for use on 1" or 25mm hollow axles. Fits:FXD 2008-2017FXST 2008-UPFLST 2008-UPFLT 2008-UPAdditional Information UOM1 - EA ManufacturerJims ...

V-Twin - 16-1194 - Jims Swingarm Bearing Installer ToolDescriptionJims swingarm bearing installer tool can be used on both the drive side and brake side bearings, which are at diffent depths, for easy and accurate installation.A remover has been added to...

V-Twin - 16-1193 - Jims FLT Inner Primary Shifter Shaft Bushing ToolDescriptionJims FLT inner primary shifter shaft bushing tool easily removes both worn bushings and quickly installs the new bushings to the proper location at the same time, without...

V-Twin - 16-1192 - Jims XL Sprocket Nut SocketDescriptionJims XL sprocket nut socket is designed specifically for XL models to remove, install and properly tighten the front final drive sprocket/pulley. Fits:XL 1991-UPAdditional Information UOM1 - EA ...

V-Twin - 16-1191 - Jims M8 Shifter Mechanism Sleeve Remover and InstallerDescriptionJims shifter mechanism sleeve is for removing and installing the shifter mechanism sleeve in M8 transmissions. The sleeve can be removed and installed correctly without...

V-Twin - 16-1190 - Jims M8 Countershaft 1st Scissor Gear Alignment ToolDescriptionEssential for installation of the countershaft 1st scissor gear, this tool ensure that the scissor gear teeth mesh correctly with the mainshaft 1st fear. For M8 models...

V-Twin - 16-1189 - Jims M8 Valve Spring Compressor AdapterDescriptionJims valve spring compressor adapter for diassembly and assembly of the multiple smaller valves on M8 models.*NOTE: Conical valve spring adapter only to be used with VT #16-1771 Valve...

V-Twin - 16-1188 - Jims M8 Cylinder Head Holder ToolDescriptionJims cylinder head holder tool is two sided, one side threaded for Twin Cam heads, and the other threaded for M8 models. Fits:FXST 1999-UPFLST 1999-UPFLT 1999-UPFXD 1999-2017Additional...

V-Twin - 16-1187 - Jims M8 Wrist Pin Remover AdapterDescriptionJims wrist pin remover adapter tool quickly and easily removes the wrist pins in M8 engines.To save space in the tool box, use with Jims TC-88 wrist pin remover tool. Fits:FLST 2018-UPFLT...

V-Twin - 16-1186 - Jims M8 Cylinder Hold Down Nuts KitDescriptionJims cylinder hold down nuts keep the cylinders in place when the heads are removed from the engine. Useful when installing the second cylinder over the piston and rings after the first...

V-Twin - 16-1185 - Jims M8 Camshaft Needle Bearing Remover and InstallerDescriptionJims camshaft needle bearing remover and installer tool is required for correct and accurate replacement of the camshaft inner needle bearing for M8 models.This tool holds...

V-Twin - 16-1184 - Jims M8 Left Main Seal InstallerDescriptionJims left main bearing oil seal installer assists with perfect installation and adds the advantage of allowing the alternator stator to remain in place during opertaion. For M8 models.*NOTE:...

V-Twin - 16-1182 - Jims M8 Main Bearing Remover and InstallerDescriptionJims main bearing remover and installer tool removes the left and right main bearing without damaging the case, it also provides correct alignment and depth during installation. For...

V-Twin - 16-1181 - Jims M8 Balancer Scissor Gear Alignment Screw ToolDescriptionJims balancer scissor gear alignment screw tool holds the two halves of the spring loaded scissor balancer gear in alignment before removal for easy installation. For use on...

V-Twin - 16-1171 - Jims Compression Release ValveDescriptionThis valve is used with Jims compression release valve tool. Release valve will make starting your engine effortless.Set of two. Drill and tap each cylinder head and thread in the self-sealing...

V-Twin - 16-1169 - Jims Compression Release Valve ToolDescriptionUse this tool for machining all Twin Cam heads for compression releases. Installs easily on front or rear head, with or without valves installed.Order the compression releases separately...

V-Twin - 16-1164 - Piston Pin Support PlateDescriptionThe Jims piston support plate provides a non-marring flat support to push the bottom of the piston as rings and cylinder are installed over piston. Fits:FXST 1984-1998XL 1957-UPFXR 1982-1994FLT...

V-Twin - 16-1163 - Balancer Shaft Retention Pin for TC-88DescriptionUse the balancer shaft retention pin tool secures the engine balancers on TC-88B engines when servicing flywheel assembl y. This tool locks into the balancers sprocket pin holes to...

V-Twin - 16-1147 - Number Stamp Holder ToolDescriptionNumber stamp tool holds the letter or number stamps from the motor number stamp sets. Fits:Custom applicationAdditional Information UOM1 - EA MeasurementsAdditional InformationSlot Length:...

V-Twin - 16-1134 - Jims Rolling Buddy Engine Dummy PlateDescriptionJims rolling buddy engine dummy plate is to be used on all rubber mount Big Twins.This tool will allow chassis to be moved once the engine has been removed from the frame. Fits:FLT...

V-Twin - 16-1079 - Jims M8 Oil Pump Alignment ToolDescriptionJims oil pump alignment tool is the perfect aid for the technician to either assemble as individual components with supplied studs or as an assembly with the alignment dowel.For the cam support...