Tools

V-Twin - 16-1280 - Jims Cam Bearing Puller ToolDescriptionThe Jims cam bearing puller tool is used to remove the bearing from the crankshaft and is designed to do this with no slipping or binding...

V-Twin - 16-1276 - Jims TC-88 Wrist Pin Remover ToolDescriptionJims wrist pin remover tool will cut the time it takes to remove and install wrist pins.This remover tool can be easily used by one...

V-Twin - 16-1275 - Jims TC-88 Crankshaft Rear Bearing ToolDescriptionThis crankshaft bearing tool is designed to remove and repla ce the right crankcase bearing in and out with no damage to crankcase...

V-Twin - 16-1274 - 4-Speed Transmission Arbor ToolDescriptionThis 4-speed transmission arbor tool is what you need to replace the clutch hub nut to allow test rotation with 1/2" drill. Fits:FX...

V-Twin - 16-1273 - TC Beta Engine StandDescriptionThe Beta engine stand is powder coated steel and clears the rear balancer housing of the Beta style TC case. Fits:FLT 1999-2016FLST 1999-2017FXST...

V-Twin - 16-1270 - Rider Tool KitDescriptionRider tool kit fits into the included 7" x 2" blue zip-up pouch.17 piece tool kit. ...

V-Twin - 16-1267 - Rear Sprocket Rivet ToolDescriptionRear sprocket rivet tool will hold sprocket in place to install rivets by a hammer.This is a 5 piece set. Includes drum holder, drum collar,...

V-Twin - 16-1264 - Motor Number Stamp SetDescriptionHardened steel stamps to restore motor numbers on early motors.Sold as a 22 piece set. Set has many variations of numbers, letters and shape...

V-Twin - 16-1261 - Transmission Main Gear Nut WrenchDescriptionThis tool is used to remove the 2-1/4" hex nut from the main drive gear which secures the rear drive transmission pulley. To be used...

V-Twin - 16-1204 - Jims M8 FXST Engine StandDescriptionJims M8 FXST engine stand, needed for any powertrain work, is built from .125" steel and powdercoated blue. Fits:FLST 2018-UPFXST...

V-Twin - 16-1203 - Jims M8 Flywheel Locking ToolDescriptionJims M8 flywheel locking tool has an added o-ring to prevent oil seepage. This tool is designed to specifically locate and lock the flywheel...

V-Twin - 16-1202 - Jims XL Primary Locking BarDescriptionJims primary locking bar tool locks the primary drive on XL models to facilitate crankshaft sprocket nut removal and installation, along with...

V-Twin - 16-1201 - Jims M8 Cylinder Torque Plate KitDescriptionThis Jims cylinder torque plate tool kit simulates stress conditions when boring and honing cylinders. For M8 models. Fits:FLT...

V-Twin - 16-1200 - Jims M8 Left Main Seal Removal ToolDescriptionJims left main seal removal tool is for M8 models. Fits:FLT 2017-UPFXST 2018-UPAdditional Information

V-Twin - 16-1199 - Jims M8 FLT Engine StandDescriptionJims M8 FLT engine stand, needed for any powertrain work, is built from .125" steel and powdercoated blue. Fits:FLT 2017-UPAdditional Information

V-Twin - 16-1197 - Jims Fork Cap Allen Socket ToolDescriptionJims fork cap large allen head socket tool for use on 49mm forks. Fits:FLT 2014-UPAdditional Information

V-Twin - 16-1195 - Jims Hollow Axle Installation Guide ToolDescriptionJims axle installation guide tool is for use on 1" or 25mm hollow axles. Fits:FXD 2008-2017FXST 2008-UPFLST 2008-UPFLT...

V-Twin - 16-1194 - Jims Swingarm Bearing Installer ToolDescriptionJims swingarm bearing installer tool can be used on both the drive side and brake side bearings, which are at diffent depths, for...

V-Twin - 16-1192 - Jims XL Sprocket Nut SocketDescriptionJims XL sprocket nut socket is designed specifically for XL models to remove, install and properly tighten the front final drive...

V-Twin - 16-1191 - Jims M8 Shifter Mechanism Sleeve Remover and InstallerDescriptionJims shifter mechanism sleeve is for removing and installing the shifter mechanism sleeve in M8 transmissions. The...

V-Twin - 16-1189 - Jims M8 Valve Spring Compressor AdapterDescriptionJims valve spring compressor adapter for diassembly and assembly of the multiple smaller valves on M8 models.*NOTE: Conical valve...

V-Twin - 16-1188 - Jims M8 Cylinder Head Holder ToolDescriptionJims cylinder head holder tool is two sided, one side threaded for Twin Cam heads, and the other threaded for M8 models. Fits:FXST...

V-Twin - 16-1187 - Jims M8 Wrist Pin Remover AdapterDescriptionJims wrist pin remover adapter tool quickly and easily removes the wrist pins in M8 engines.To save space in the tool box, use with Jims...

V-Twin - 16-1184 - Jims M8 Left Main Seal InstallerDescriptionJims left main bearing oil seal installer assists with perfect installation and adds the advantage of allowing the alternator stator to...

V-Twin - 16-1181 - Jims M8 Balancer Scissor Gear Alignment Screw ToolDescriptionJims balancer scissor gear alignment screw tool holds the two halves of the spring loaded scissor balancer gear in...

V-Twin - 16-1164 - Piston Pin Support PlateDescriptionThe Jims piston support plate provides a non-marring flat support to push the bottom of the piston as rings and cylinder are installed over...

V-Twin - 16-1163 - Balancer Shaft Retention Pin for TC-88DescriptionUse the balancer shaft retention pin tool secures the engine balancers on TC-88B engines when servicing flywheel assembl y. This...

V-Twin - 16-1147 - Number Stamp Holder ToolDescriptionNumber stamp tool holds the letter or number stamps from the motor number stamp sets. Fits:Custom applicationAdditional Information

V-Twin - 16-1134 - Jims Rolling Buddy Engine Dummy PlateDescriptionJims rolling buddy engine dummy plate is to be used on all rubber mount Big Twins.This tool will allow chassis to be moved once the...

V-Twin - 16-1079 - Jims M8 Oil Pump Alignment ToolDescriptionJims oil pump alignment tool is the perfect aid for the technician to either assemble as individual components with supplied studs or as...

V-Twin - 16-1070 - Rider Tool Kit for 2017 FLTDescriptionDIY Touring tool kit for 2017 FLT models. Kit includes rider tools and service tools for the rider-mechanic.This DIY tool kit will help the...

V-Twin - 16-1063 - Rod Alignment Plate ParkerizedDescriptionRod alignment plate features a cast iron construction with a parkerized finish, for Big Twin engines. Fits:FL 1941-1985EL...

V-Twin - 16-1055 - OE Crankshaft Locking Tool for XLDescriptionOE crankshaft locking tool fits 1991-1999 XL models by engaging the pinion shaft splines. This allows removal and torquing of the pinion...

V-Twin - 16-1051 - Jims TC-88 Connecting Bushing ToolDescriptionTo remove and replace wrist pin bushing without removing connecting rods from crankcase, use the Jims TC-88 connector rod bushing tool...

V-Twin - 16-1047 - Flute Tap Tool 3/8 inch-18 Bright ColbaltDescriptionFlute tap tool 3/8"-18 NPT thread features 4 flutes with a bright cobalt finish. Fits:Custom applicationAdditional Information

V-Twin - 16-1046 - Flute Tap Tool 1/8 inch-27 Bright ColbaltDescriptionFlute tap tool 1/8"-27 NPT thread features 5 flutes with a bright cobalt finish. Fits:Custom applicationAdditional Information

V-Twin - 16-1045 - Jims Magnetic Tappet Holder Tool SetDescriptionJims magnetic tappet holder tool set holds the tappets up while changing cams, cam support plate or oil pump on all TC-88 and M8...

V-Twin - 16-1043 - Sifton Cam Cover Bushing Remover ToolDescriptionSifton cam cover bushing remover tool will remove the cam cover bushing and will also remove cam bushing in case.This tool is...

V-Twin - 16-1042 - Sifton Outer Primary Cover Starter Bearing Removal ToolDescriptionSifton outer primary cover starter bearing removal tool removes 9063 Torrington needle bearing for Big Twin and XL...

V-Twin - 16-1041 - Flywheel Fixture Center ToolDescriptionFlywheel fixture center tool is for use on hand wheel.Thread pitch is 5/8"-11. Fits:FLST 2000-2017FXD 2000-2017XL 2000-UPFXST 2000-2017FLT...