16" x 3.00 rear wheel assembly with chrome hub and bearings installed, chrome rim, and chrome spokes.*NOTE: The valve stem hole is on the sprocket side. **NOTE: All spokes on wheel need to be inspected and re-torqued after 500 miles of original...

Description 19" WR/KR/XR rear wheel features a natural finish hub with 9/16" ball bearings and internals installed. Laced with 6-8 gauge stainless steel spokes to a black finish 19" x 3.0" 40 hole drop center rim. Accepts a 9/16" axle shaft.Sold laced...

H-C type 2.15" x 19" alloy rim features a polished natural finish and has 40 spoke holes.Exact as original! Rim is drilled to fit Harley type applications on smaller diameter hubs. CV hole measures 8.5mm. Holes may have to be enlarged for certain spoke...

H-C type 2.15 x 18" alloy wheel rim features a polished natural finish and has 40 spoke holes.Exact as original! Outside measurement flange to flange is 2-7/8", inside diameter at bead pattern area is 2". Rim is drilled to fit Harley type applications on...

Description 21" x 2.15" WR spool wheel features a nickel plated hub, stainless steel spokes and nipples and a black H-C type rim, which accepts a 7/16" axle.Includes 21" x 2.15 wheel assembly, that is laced and trued. Wheel hub has a 3/8" inner diameter...

Replacement tank mounts can be used on Fat Bob tanks and also on custom frames where the mounts do not exist. Fits:FL 1955-1984Additional Information UOM1 - EA ManufacturerV-Twin OriginImported TypeRigid

Frame loop set is authentically forged in construction to fit the right and left set. Use on straight leg frames. Fits:FL 1955-1957EL 1936-1947U 1937-1948FL 1941-1947Additional Information UOM1 - SET ManufacturerV-Twin OriginImported 2025 Catalog...

200 XL rigid frame features a 40  rake with a 3" stretch in front legs to accept a 1-1/8" belt with 200 series tire.Frame has kickstand tab and battery box mount welded in place. Accepts a right side drive transmission and is disc brake type. For use on...

Side car frame mount set with side car loops and embossed forging factory numbers and features a raw finish. For straight leg frame restoration or repair.Set is for use with straight leg Panhead and Knucklehead Big Twin frames. Forgings are drilled to...

Weld-on brake tab features a raw finish. Mounts stock or replica frames to the rear drum brake backing plate. Fits:FL 1958-1972Additional Information UOM1 - EA ManufacturerV-Twin OriginUSA

Transmission mount plate kit is a 4 piece kit used for final alignment. Kit is for use with Hardtail models and stock and custom rigid frames.Includes upper and lower stamped plates and 2 spools (dowels) with 3/8" x 24 threads. Spools must be welded in...

Footpeg support bar set is the splined type featuring a raw steel construction.Attaches to early Sportster frames to mount footpeg stanchions. One end is splined and the other fits over the frame tube. ...

Engine mount shim is used to raise motor for front or rear clearance, when necessary.Sold in a pack of 5. Fits:FL 1941-1999EL 1936-1952Additional Information UOM5 - PK ManufacturerV-Twin OriginUSA

Black engine bar features 1" tubing.**WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide). They are not made nor intended to provide protection...

Black finish front engine guard attaches to footboard mounts and frame tubes using U-bolts.This 1936-38 style engine bar is differentiated by its flat shape sides, although it will fit as noted. Constructed of 1" diameter tubing with an accurately formed...

Engine bar features 1" tubing and a black finish.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very slow speed slide). They are not made nor intended to provide...

Chrome front engine bar.This 1936-38 style engine bar is differentiated by its flat shape sides, although it will fit as noted. Constructed of 1" diameter tubing with an accurately formed top mount. Restoration Quality! Order U-clips separately...

Raw steel front engine mount for 1948-1957 type features forged construction for strength and weld-ability hallmarks as original.Original design replacing the OEM#476664-48 #9, the first version of the Panhead front frame motor mount. Fits:FL 1948-1957EL...

Rear brake clamp for 45 models fits on the right side to secure the rear brake backing plate.*NOTE: Must be welded in place. Fits:W 1937-1952Additional Information UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages815

Replica "HM" wishbone frame features full "hallmarks" on forgings. Does not include indents or horn mounts on wishbone front legs.Neck "HM" forging is supplied separately for builders to affix. Wishbone frame has a 30  rake. ...

Replica "HM" wishbone frame features full "hallmarks" on forgings. Frame is an authentic reproduction of Replica Wishbone frame is an reproduction of a 1954 Panhead frame, but will also fit 1948-1957 Rigid.*NOTE: There are no serial numbers stamped on...

Replica "HM" wishbone frame features full "hallmarks" on forgings. Includes horn mount tabs on wishbone tubes.Hallmarks forged with the following components axle plates, side car loops, front motor mount, rear motor mount, seat yoke, rear forging engine...

Raw steel weld-on hardtail features a raw steel finish.Replaces entire rear section of the frame, for the full rigid look. *NOTE: Must be installed by a certified welder. Fits:XL 1957-1978Additional Information UOM1 - EA ManufacturerV-Twin ...

Replica engine bar features 1" tubing.Order U-clamp separately. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped,...

Replica 45 W stock style rigid frame with brazed joints features a raw finish. There's No Manufacturer's Statement of Origin, only a Bill of Sale, referencing the part number.Don't forget the pre-assembly procedure! Before primer and paint, the frame...

Replica swingarm frame is our authentic reproduction of FLH style to accept a Panhead or Shovelhead engine, 4-speed transmission, seat post, and accepts a round or square swingarm. All components are pressed and formed as stock.Frame details include...

Replica swingarm frame is an authentic reproduction of FLH style for 1965-1984.Frame accepts Panhead or Shovelhead engine, 4-speed transmission, 12v battery and round swingarm for drum brake applications or a square swingarm for disc brakes. Details...

V-Twin - 51-1003 - 1958-1964 FL Swingarm Frame Description Raw replica swingarm frame is an authentic reproduction of FLH style for 1958-1964 kick start models only. Swingarm is a non-electric start and is for use with 6 volt components. This is the...

Raw frame swingarm features forged axle plates for 3/4" axle with round tube construction. Fits:FX 1971-1972FL 1958-1972Additional Information OEM No.47500-58B UOM1 - EA FinishRaw ManufacturerV-Twin OriginImported 2025 Catalog Pages642

This replica authentic style frame neck web repair section must be welded in after cutting stock or custom frame. It features the right side lock housing.Order new lock assembly, separately. Fits:FL 1948-1984Additional Information UOM1 - EA ...

Engine bar set features left and right sides.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide). They are not made nor intended to provide...

Frame hardtail is bolt on type. Accepts drum style brakes on a rigid frame.Unit should be aligned for chain clearance prior to final bolting. DIY hardtail is easy to install as the alignment is accomplished in the mount design. The distance between the...

Frame hardtail replaces shocks on swingarm frames and is drum brake type. Unit should be aligned for chain clearance prior to final welding.DIY hardtailing is easy to install as the alignment is accomplished in the mount design provided. The distance...

Chrome front engine bar features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide). They are not made nor intended to provide...

Chrome front engine bar has 1" outer diameter.Order u-clamp separately. Bracket is offcenter by design. *WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very slow...

Engine bar with 1" tubing.Order U-clamp separately. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very slow...

Engine bar features 1" tubing for use on early wishbone frames.Order U-clamp separately. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances...

Rigid frame bar for the rear with 7/8" tubing features a chrome finish.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide). They are not made...

Engine bar features 1" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very slow speed slide). They are not made nor intended to provide protection from...

Rigid frame bar for the rear with 7/8" tubing features a black finish.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide). They are not made nor...