Intake manifold kit for use on Panhead models with Linkert carburetors and o-ring intake port heads.Kit is steel. Fits:FL 1955-1965Additional Information UOM1 - KIT ManufacturerV-Twin OriginImported 2025 Catalog Pages712

Linkert carburetor bowl lock nut and drain is zinc plated and is for use with all brass Linkert bowls. The nut and drain allows water to drain without removing the bowl.This special float bowl nut with a 1/4" allen drain screw, allows the draining of...

Zinc lock nut with linkert needle and seat kit.Kit is correct for 1949-1954 Tombstone tail lamps. Wire loom includes tail lamp piece on the fender end, spiral spring cover and segemented channel for wire loom. Fits:FL 1941-1965G 1936-1957EL 1936-1952W...

Linkert carburetor nylon bushing kit is for the throttle shaft on all brass linkert carburetors.Includes nylon throttle shaft bushing set, shaft ring and full stainless steel screw and nut kit. Steel and nulon bushings are available separately. Fits:FL...

Linkert carburetor adapter mounts to 4 bolt stock manifold to allow the use of a Mikuni or Dellorto 38mm spigot carburetor. Features a natural alloy finish.*NOTE: Clamps and rubber adapters not included. Fits:FL 1941-1965EL 1941-1952Additional...

Linkert carburetor adapter mounts to 3 bolt stock manifold to allow the use of a Mikuni or Dellorto 38mm spigot carburetor. Machined with natural alloy finish. Fits:EL 1936-1939G 1936-1957U 1936-1948W 1936-1952Additional Information UOM1 - EA ...

Linkert carburetor screw kit features zinc plated and stainless steel screws and washers for choke and throttle doors and air cleaner back plates.*NOTE: Zicad is a dull shade of zinc similar to cadmium. Fits:FL 1936-1965G 1936-1957EL 1936-1952W...

Zinc plated linkert cable bracket kit includes the small cable u-clamp half, bracket and spring. Kit is for use with linkert carburetors.For use on left side Overhead Valve snap throttle installations. Fits:FL 1941-1965EL 1936-1952Additional Information ...

Four bolt WR intake manifold for Linkert carburetor is cast iron with zinc plating.NOTE: For WR and K use, order correct manifold nuts and seals separately. Installation requires the nipples to be screwed into the cylinder depth so that the manifold...

Replica Linkert carburetor cork float includes shoulder bolt and screw.This cork float manufactured to OEM specifications and helps maintain a proper level of fuel in the carburetors float bowl for optimum performance. *NOTE: Sold as a pack of 5. ...

45" WL cast iron intake manifold in a zinc finish is the 3 bolt replacement type for brass Linkert carburetors.*NOTE: Nuts and brass seals not included. Fits:WL 1936-1952G 1936-1973Additional Information UOM1 - EA ManufacturerV-Twin OriginImported ...

Linkert carburetor bean pot bowl with early style hex cap features a natural aluminum finish. Bean pot bowl shape allows additional fuel, giving access for long open throttle sessions.Larger inner diameter adds 1.45 cubic inches to hold additional fuel...

Linkert 38mm carburetor adapter kit includes a three bolt adapter, intake manifold rubber adapter, and two stainless steel hose clamps.Order intake manifold separately. Fits:UL 1937-1948WL 1935-1952Additional Information UOM1 - KIT ManufacturerV-Twin ...

Linkert M88 carburetor parts kit includes all components, except the brass body and throttle arm.WL and WLA must be fitted with aluminum heads. (Higher Compression) Fits:WL 1937-1952UL 1936-1948WLA 1937-1952U 1936-1948Additional Information UOM1 - KIT ...

Copper Linkert carburetor float bowl cap with 9/16 - 20 thread includes sealing washer.For use with Linkert carburetor float bowl and gaskets. Fits:FL 1941-1965Additional Information OEM No.27390-33 UOM1 - EA ManufacturerV-Twin OriginImported 2025...

Linkert carburetor body pin is 1/8" x 3/8". Fits:WL 1933-1952UL 1937-1948FL 1941-1965EL 1936-1940VL 1933-1934Additional Information UOM2 - PK ManufacturerV-Twin OriginImported 2025 Catalog Pages708

Linkert 34mm carburetor adapter kit includes a three bolt adapter, intake manifold rubber sleeve, and two stainless steel hose clamps.Order intake manifold separately. Fits:UL 1937-1948WL 1935-1952Additional Information UOM1 - KIT ManufacturerV-Twin ...

Fuel strainer filter has a zinc finish.Order screen separately. Fits:FL 1942-1949Additional Information OEM No.62250-41 UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages1195 Tech NoteRequired to use #8927-3 screen.

Carburetor cable block kit includes screws, washer, and cotter pin.Block and cotter pin are stainless steel and screw and washer are cadmium plated. Carburetor cable block kit attaches inner choke or throttle cable to throttle arm. Fits:UL 1937-1948FL...

Fuel strainer filter body only with zinc finish. Comes with cap.Order screen and gaskets separately. Fits:FL 1950-1965Additional Information OEM No.62250-50 UOM1 - EA MeasurementsAdditional InformationThread One Side: 7/16"-20Thread Other Side:...

Brass intake manifold clamp set is two piece type with o-ring type seals. Fits:FX 1971-1977FL 1955-1977XL 1957-1977Additional Information UOM1 - SET MeasurementsAdditional InformationOuter Diameter: 2-1/4"Inner Diameter: 1-3/4"Thickness:...

Linkert M-18 carburetor kit for 1" linkert brass carburetors with 7/8" venturi.*NOTE: For the float arm installation, the center prong of the float arm should have .003" of clearance, in order for the arm and needle to move freely. Fits:G 1930-1952W...

Bendix carburetor kit includes 38mm Bendix carburetor with adjustable main jet, throttle handle with grips, cable and cable bracket, and 7" round logo air cleaner with support. Kit includes seal adapters to use on Pre-1978 O-ring heads.Kit accepts 3/8"...

Petcock shutoff fuel rod seat with 1/2"-20 and 3/4"-18 external threads. Petcock features a zicad finish.The smooth end has a 7/8"-20 internal thread. ...

Linkert M74 1-1/2" throat carburetor hardware kit includes nitrophyl "unsinkable" float.*NOTE: For the float arm installation, the center prong of the float arm should have .003" of clearance, in order for the arm and needle to move freely. *NOTE: M-74...

Linkert M88 1-1/4" throat carburetor hardware kit includes all parts except body and is for stock rebuilds with low speed fixed jets.WL and WLA must be fitted with aluminum heads. (Higher Compression) Linkert M88 includes fixed hi-speed jet, as...

Linkert M51 1-1/4" carburetor hardware kit includes all parts except brass body.This is for 1-1/4" bore linkert carburetors. *NOTE: For the float arm installation, the center prong of the float arm should have .003" of...

Intake manifold kit is constructed of cast iron and includes brass seals, nuts, screws, lock washers, and gasket to fit Knucklehead and Panhead models. Kit is shipped unassembled. Manifold is zinc plated.The Width of the base of the manifold measures...

Flanders linkert carburetor bracket.. Fits:FL 1948-1965Additional Information UOM1 - EA ManufacturerV-Twin OriginUSA 2025 Catalog Pages708

Linkert float arm assembly includes "unsinkable" linkert M float and a V-Twin one piece cast brass float arm,for smooth operation. Also includes the bolt and nut and pivot cap and pin set for mounts.The float will not leak or swell and is impervious to...

Parkerized brake lever connecting links kit includes connecting links, pin, washer, and a cotter pin. Fits:G 1930-1957Additional Information UOM1 - KIT FinishParkerized ManufacturerV-Twin OriginUSA 2025 Catalog Pages823

Brake shaft lever is for the left hand side. Fits:FL 1936-1957 SidecarAdditional Information OEM No.87678-36 UOM1 - EA ManufacturerV-Twin OriginUSA 2025 Catalog Pages823

Parkerized reproduction of the washer, nut and washer used on 1936-1957 Side Car, 1936-1948 Big Twin and 1941-1957 Servi-car models. Fits:EL 1936-1940G 1941-1957Side Car 1936-1957U 1937-1948FL 1941-1948Additional Information OEM No.44270-36 UOM1 - KIT ...

Parkerized right end brake operating shaft lever. Fits:G 1936-1957Additional Information UOM1 - EA FinishParkerized ManufacturerV-Twin OriginUSA 2025 Catalog Pages823

Cadmium plated oil return line elbow fitting. Fits:XLH 1958-1966XLCH 1953-1962 Early 1962Additional Information OEM No.63540-52 UOM1 - EA ManufacturerV-Twin OriginUSA 2025 Catalog Pages821

Cadmium plated oil feed line elbow fitting. Fits:XLCH 1962-1965 Late 1962Additional Information OEM No.62696-62 UOM1 - EA ManufacturerV-Twin OriginUSA 2025 Catalog Pages821

Cadmium plated oil feed line elbow fitting. Fits:XLH 1958-1966XLCH 1953-1962 Early 1953 - Early 1962K 1953-1962 Early 1953 - Early 1962Additional Information OEM No.63540-53 UOM1 - EA ManufacturerV-Twin OriginUSA 2025 Catalog Pages821

Parkerized left end brake crossover shaft lever. Fits:G 1941-1957Additional Information OEM No.6181-41 UOM1 - EA FinishParkerized ManufacturerV-Twin OriginUSA 2025 Catalog Pages823

V-Twin - 34-1804 - Panhead Phillips Screw Set Zinc PlatedDescriptionZinc plated Panhead Phillips 3 piece screw set measures 1/4"-20 x 5/8". Fits:FLST 1993-2007XL 1988-UPFXST 1993-2007FLT 1993-2007FXR 1993-1994Additional Information UOM1 - SET ...

V-Twin - 34-1803 - Panhead Phillips Screw Set Zinc PlatedDescriptionZinc plated Panhead Phillips 3 piece screw set measures M6 x 1 x 16mm. Fits:FLST 1993-2007XL 1988-UPFXST 1993-2007FLT 1993-2007FXR 1993-1994Additional Information UOM1 - SET ...