Jims - 966 Starter Jackshaft Seal Installer Tool fits '94-'06 Big Twin Models (Except '06 Dyna (OEM #120-66)) Features: Easily aligns and installs starter jackshaft seal without distorting or damaging seal Seal is located in upper part of inner...

Jims - 967 Inner Primary Bearing and Seal Remover/Installer Tool fits 'L84-'06 FXST/​FLST & '85-'06 Touring & Dyna Models Features: Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer...

Jims - 976 Engine Rotator Tool fits '55-'06 Big Twin Models (Except '06 Dyna Glide) Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 951 Original Equipment Torque Plate fits '99-'17 Twin Cam 88”, 96” or 103”, 3.75”-3.875” Models Features: Torque plates must be used when boring or honing late-model aluminum cylinders Simulate running stress...

Jims - 915 Installation Inner Ball Bearing Tool fits '00-'17 Twin Cam “B” Motors Models Features: Accurately and safely install the inner balancer bearing mounted in the left engine case All done on a work bench without using an arbor...

Jims - 916 Case Support Blocks fits '00-'17 Twin Cam Models “B” Motors Features: Aluminum blocks have inserted Delrin® pads that rest against case to prevent marring and to support the case Keeps case level when using bearing pullers...

Jims - 1278-3 Camshaft Bearing Installation fits '99-'17 Twin Cam Models Features: Replacement drive for JIMS® Cam Bearing Installation Tool

Jims - 780 Seal Leak Tester Tool fits '00-'17 Twin Cam “B” Motors Model Features: Required to seal the oil passage way from right case to the balancer tensioner plate; leaking can cause over oiling of the lower end that decreases...

Jims - 902 Blue Motor Stand fits '00-'17 Twin Cam “B” Motor Model Features: Makes working on motors easier with better access Made in the USA Note: For Twin Cam "B" motor.

Jims - 766 Adapter for '84-'99 Evo Hydraulic Tappets Features Adapter for Harley-Davidson® Evolution hydraulic tappets Must use in conjunction with JIMS® tappet pump and test stand part# 3801-0192.

Jims - 1042-7 Expander Dowel Tool fits All '00-'17 Twin Cam, '00-'22 Sportster & '02-'17 V-Rod Models Features: Removes and installs 3/4", 1", and 25 mm wheel bearings with or without (Anti-Lock Brake System) ABS Made in the U.S.A.

Jims - 5532 Vacuum Tappet fits '84-'20 Big Twin Models w/ Hydraulic Tappet Assemblies Features: Removes the risk of using the starting system to pump up the lifters or damage to the valve train at low rpm if the lifters are not fully bled Special...

Jims - 5809 Cylinder Hold Down Tool fits '17-'20 M-Eight & '99-'17 Twin Cam Models Features: Useful when installing the second cylinder over the piston and rings after the first cylinder has been installed One end fits Twin Cam models, while the...

Jims - 775 Removal/Installation Main Seal Tool fits '99-'17 Twin Cam Models Features: Install and remove crank case main seal while the engine is still in the chassis Includes necessary adapters for '88 and '96 Twin Cams Made in the U.S.A.

Jims - 5506 Magnetic Tappet Holder fits all Twin Cam & M-Eight Models Features: Never turn the engine over if the tappet will not spin with your fingers after adjustments were made It is very important that the engine is not rotated while...

Jims - 1664 5-Speed Transmission Shifter Shaft Sleeve Tool fits '80-'83 FLT/​FLHT/​FXR, '84-'99 Big Twins & '84-'00 FLHT/​FXR/​FXD Models Features: Can be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drum Use...

Jims - 1073 Cylinder Torque Plates fits '66-'99 Big Twin Models Features: Torque plates must be used when boring or honing late-model aluminum cylinders Simulate running stress conditions Come with instructions Made in the U.S.A.

Jims - 1147 Alternator Rotor Puller fits '97-'06 Big Twin Models Features: A must-have tool for 45A charging systems; will also work on any Harley-Davidson® alternator system that has threaded puller holes Tool protects threads on sprocket shaft...

Jims - 95660-77 4-Speed Seal Driver fits '82-'86 Big Twin Models Features: Optional drivers used in conjunction with main shaft seal tool allow installation of seals Fitment 1986 Harley-Davidson Softail Heritage...

Jims - 2244 3/8" 35 mm Fork Nut Socket fits For Big Twin & Sportster Models Features: Used to remove and install top fork nuts on fork tubes Rubber protector inside socket Will clear most handlebars Made in the U.S.A...

Jims - 2240 Head Holder Guide Tool '48-'04 Big Twin, '57-'03 Sportster & Some SE CVO Twin Cam Models (5/16” Valve Guides) Features: Adapters are supported by a stand that makes it easy to press valve guides in and out A special guide...

Jims - 1146 Crankshaft Bearing Installer fits '00-'17 Twin Cam “B” Motors Models Features: Designed to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearing Made in the U.S.A...

Jims - 1162 Caliper Piston Remover fits '00-'07 Big Twin & '00-'03 Sportster 4-Piston Front/​Rear Calipers Models Features: Prevents damage to pistons and cylinders when installing new seals and wipers Holds pistons square in their cylinder...

Jims - 1167 Balancer Shaft/Removal Bearing Tool fits '00-'06 Twin Cam “B” Motors Models Features: Installing portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's bore Pulls the...

Jims - 1169 Compression Release Valve Installation Kit fits Twin Cam Models Features: Installation kit includes fixture, drill bit, spot face bit and thread-tapping tool Simply drill, spot face, tap and install compression release valves Works on...

Jims - 1110 0.105" Camshaft Pinon Gauge Pins fits '54-'89 Big Twin Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 1989 Harley-Davidson Electra Glide Ultra...

Jims - 1111 0.108" Camshaft Pinion Gauge Pins fits '90-'99 Big Twin Evolution Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...

Jims - 1705 Exhaust Drill Plate fits '84-'17 Big Twin (Except M-Eight), '86-'22 Sportster & '94-'09 Buell Models (Except 1125R) Features: Will position the seal evenly into the exhaust port of head Tool can be used with exhaust flange nuts Made...

Jims - 2392 Head Bolt Torque Gauge fits all Twin Cam & Evolution Engines Models Features: This accurate gauge allows the measuring of 90° when tightening head bolts Torquing sequence laser engraved on gauge, with instructions Works on all...

Jims - 1034 Sprocket Shaft Holder fits '55-'99 Big Twin & '99-'06 Twin Cam (Except '06 Dyna) Features: Used to hold flywheel assembly in vise, with or without left case attached Made in the U.S.A...

Jims - 95760-57 Bushing Bearing Puller fits '66-'17 Big Twin (Except M-Eight), '57-'22 Sportster & Buell Models (Except 1125R) Features: Used to remove rocker bushing or bearing in one easy operation Made in the U.S.A...

Jims - 1052 Oil Pump Snap Ring Installer fits Big Twin Oil Pumps (Except Twin Cam/M-Eight) Features: Just apply oil to ring expander, slip ring up to the big end of ring expander, hold up to the end of the shaft, then push ring onto the shaft with...

Jims - 1053 Oil Pump Seal Installer fits Big Twin Aluminum Oil Pumps (Except Twin Cam/M-Eight) Features: For use on all Big Twin aluminum oil pumps (except Twin Cam/M8) Easily installs oil pump seal below gear surface for a no-leak fit Made in the...

Jims - 38515-90 Clutch Spring Compressor fits '90-'97 Big Twin & '91-'03 Sportster Models Features: For '91-'03 XL applications, compressor nut must be used in conjunction with compressor tool Used to release clutch spring so retainer ring can...

Jims - 1710 Outer Race Snap Ring fits '69-'02 Big Twin Models Features: Used for removing and installing the Timken® bearing outer race snap ring A must for replacing rings in OEM and aftermarket cases Made in the U.S.A...

Jims - 33443-84 Tappet Aligning Tool fits 'L76-'17 Big Twin Models (Except M-Eight) Features: Can also be used to align rocker box bases on Evolution head (requires two tools) Also used in Harley-Davidson® Twin Cam oil pump alignment...

Jims - 1745 Bearing Simulator fits '70-'02 Big Twin Models Features: Designed to allow quick and easy removal and replacement of flywheel assembly in the left-side crankcase when checking rod-to-case, piston-to-flywheel or cylinder-to-flywheel...

Jims - 2260 Sprocket Lock Tool fits '99-'17 Twin Cam & '80-'99 Big Twin Models w/ Rear Belt Drive Features: Lock the transmission pulley for removing or installing pulley nut Made in the U.S.A...

Jims - 2189 Transmission Shaft Installer fits '83-'06 Big Twin Models Features: Installs transmission shaft without the use of a hydraulic or arbor press Made in the U.S.A. Fitment 2008 Harley-Davidson Fat Bob...

Jims - 1288 Crankshaft Guide fits '99-'17 Twin Cam & '03-'09 Buell XB9R/X B9S Models Features: Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A...