Jims - 987 Cruise Drive/6-Speed Main Bearing Installer Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Safely installs new main transmission case bearing; does not remove bearing Holds bearing square to its bore, eliminating any marring...

Jims - 989 Main Drive Gear Sprocket Locknut Wrench fits '07-'21 Big Twin & '06 Dyna Models Features: Removes hex nut from end of main drive gear that secures the rear drive transmission pulley Extra-long two-piece design Made in the USA Inner...

Jims - Shifter Shaft Removal Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Loosens and removes both shifter shafts from transmission door, allowing further disassembly of transmission Made in the...

Jims - 939 Sealed Wheel Bearing Tool fits '00-'17 Twin Cam, '00-'22 Sportster & '02-'17 V-ROD Models Features: Removes and installs 3/4", 1" and 25 mm wheel bearing with or without Anti-Locking Brake System (ABS) Made in the U.S.A...

Jims - 901 Cruise Drive/6-Speed Main Drive Gear Remover Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Removes the main drive gear from the main bearing correctly while in the transmission case Eliminates the need of an arbor press and...

Jims - 911 Cruise Drive/6-Speed Trap Door Bearing Remover/Installer fits '07-'20 Big Twin & '06 Dyna Models Features: Accurately installs and removes lubed ball bearing into transmission trap door No arbor press needed Made in the U.S.A...

Jims - 767 6-Speed Transmission Case Shifter Shaft Seal Installer fits '06-'20 Big Twin & '84-'05 Sportster Models Features: Makes installing shifter shaft seal precise and effortless Aligns, centers and installs shifter seal to correct...

Jims - 768 5-Speed Transmission Case Shifter Shaft Seal Installer fits '80-'99 Big Twin, '99 Twin Cam, '99-'06 FXST & '99-'05 FLT/F LHT/​FXD Models Features: Makes installing shifter shaft seal precise and effortless Aligns, centers and...

Jims - 739 5 & 6-Speed Cruise Drive Countershaft Bearing Remover/Installer Tool Features: Install or remove the closed-end countershaft bearing on all 5-speed or 6-speed transmissions without using a press or tapping it in with a transmission...

Jims - 729 Inner Primary Seal/Bearing Removal/Installation Tool fits '85-'20 Big Twin Models Features: Gives a much better feel than a press while eliminating the possibility of applying too much pressure to the parts Provides precise installation...

Jims - 967-4 Installation/Removal Inner Primary Bearing Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearing Also...

Jims - 967-5 Inner Primary Bearing Tool fits '07-'19 Big Twin & '06 Dyna Models Features: Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearing Also removes and installs...

Jims - 2268 Main Case Seal Installer Tool fits '85-'06 5-Speed Big Twin & Aftermarket 6-Speeds Models Features: Ensures correct alignment, seal protection and depth when installing the seal Made in the...

Jims - 5502 Ultimate Clutch Adjusting Tool fits '85-'20 Big Twins Models w/ Mechanical Clutch Features: Allows the quick and accurate tightening of the clutch adjusting screw jam nut without having the screw change position No more guessing or...

Jims - 5517 Removal/Installation Shifter Mechanism Sleeve Tool fits '06 Dyna & '07-'20 Big Twin w/ 6-Speed Cruise Drive Transmission Features: A real time saver for removing and installing the shifter mechanism sleeve in cruise drive Big Twin...

Jims - 5534 Compensator Bolt Driver Torx Socket fits '14-'21 Big Twin Models Features: Correct-style driver/socket for the compensating sprocket retaining fastener Made in the USA For use with Jim's part# 10500031 compensator bolt...

Jims - Cruise Drive Countershaft 1st Scissor Gear Alignment Tool fits '17-'20 M-Eight Models Features: Essential for installing countershaft 1st scissor gear in cruise drive transmissions Ensures scissor gear teeth mesh correctly with the mainshaft...

Jims - 988 Valve Spring Compressor fits '05-'17 Twin Cam (Except SE Models), '04-'22 Sportster (Except RH Sportster) & Buell Models (Except 1125R) Features: Used to remove and replace valve and new-style conical valve spring Requires use of JIMS...

Jims - 967 Inner Primary Bearing and Seal Remover/Installer Tool fits 'L84-'06 FXST/​FLST & '85-'06 Touring & Dyna Models Features: Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer...

Jims - 972 6-Speed Main Drive Gear Seal Installer fits all '07-'20 Big Twin & '06 Dyna Models Features: Use to install main drive gear oil seal to the proper depth with transmission assembled Includes protective sleeve for seal, which can be...

Jims - 976 Engine Rotator Tool fits '55-'06 Big Twin Models (Except '06 Dyna Glide) Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 937 7mm Valve Guide Remover fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125R) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made...

Jims - 938 7mm Valve Guide Installer fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125CR) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve...

Jims - 1042-7 Expander Dowel Tool fits All '00-'17 Twin Cam, '00-'22 Sportster & '02-'17 V-Rod Models Features: Removes and installs 3/4", 1", and 25 mm wheel bearings with or without (Anti-Lock Brake System) ABS Made in the U.S.A.

Jims - 5532 Vacuum Tappet fits '84-'20 Big Twin Models w/ Hydraulic Tappet Assemblies Features: Removes the risk of using the starting system to pump up the lifters or damage to the valve train at low rpm if the lifters are not fully bled Special...

Jims - 5808 Valve Spring Compression Collar Tool fits '17-'21 M-Eight Models Features: Valve spring collar allows existing compressor to remove smaller valves on M8 engines For use with JIMS® Valve Spring Compressor Tool (PART# DS-196013) Made...

Jims - 5809 Cylinder Hold Down Tool fits '17-'20 M-Eight & '99-'17 Twin Cam Models Features: Useful when installing the second cylinder over the piston and rings after the first cylinder has been installed One end fits Twin Cam models, while the...

Jims - 5828 Cylinder Head Holder Tool fits '17-'22 M-Eight & All Twin Cam Models Features: Allows you to easily position head for all types of work Use to hold head in vice through spark plug hole For use with Milwaukee Eight engine series Has...

Jims - 5829 Cylinder Torque Plates fits '17-'20 M-Eight 107”, 114” Models Features: Torque plates must be used when boring or honing late-model aluminum cylinders Simulate running stress conditions Come with instructions Made in the U...

Jims - 5834 Engine Stand fits '18-'21 M-Eight Softail Models Features: For use on the Milwaukee Eight™ engine series JIMS Milwaukee-Eight® Softail® engine stand is designed to work on all Milwaukee-Eight® Softail engines JIMS...

Jims - 5832 Ball Bearing Remover Tool fits '17-'20 Softail & Touring Models Features: Easily remove the balancer bearings in both Touring and Softail models without damage to the crankcase Fitment 2020-2021 Harley-Davidson Road...

Jims - 5833 Ball Bearing Installation Tool fits '17-'20 Softail & Touring Models Features: All Milwaukee-Eight® (M8) engines incorporate balancers to reduce vibration Designed to precisely install these bearings in the proper location for...

Jims - 5835 Valve Spring Compressor Tool fits '17-'21 M-Eight Models Features: Once the cylinder is filled with compressed air, the technician can easily rotate the tool and compress the top collar of the valve spring exposing the keepers to remove...

Jims - 5838 Oil Pump Alignment Tool fits '17-'21 M-Eight Engines Models Features: This tool was designed to help the technician assemble the complete cam chest correctly, in a quick and efficient manner The perfect aid for the technician to either...

Jims - 991 Case Splitting Tool fits '18-'21 M8 Softail & Touring Models Features: In order to perform any type of lower end service or performance work, it is necessary to split the crankcase into halves Simply install the tool on the primary...

Jims - 5506 Magnetic Tappet Holder fits all Twin Cam & M-Eight Models Features: Never turn the engine over if the tappet will not spin with your fingers after adjustments were made It is very important that the engine is not rotated while...

Jims - 730 Piston Tester Jet fits '18-'21 M-Eight Softail Models Features: Assists engine rebuilder to clear jet of all assembly lubes; verifies psi number the jet switches to "on" and visualizes spray pattern before cases are sealed Helps determine...

Jims - 1664 5-Speed Transmission Shifter Shaft Sleeve Tool fits '80-'83 FLT/​FLHT/​FXR, '84-'99 Big Twins & '84-'00 FLHT/​FXR/​FXD Models Features: Can be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drum Use...

Jims - 5820 Standard Rear Axle Installation Guide Tool fits '08-'21 Big Twin w/ Hollow 1” (25 mm) Features: Aligns wheel with swingarm, caliper brackets, wheel hubs and spacers Made in the USA For Big Twin models with hollow 1" (25 mm)...

Jims - 2244 3/8" 35 mm Fork Nut Socket fits For Big Twin & Sportster Models Features: Used to remove and install top fork nuts on fork tubes Rubber protector inside socket Will clear most handlebars Made in the U.S.A...