Engine

Jims - 975 Engine Rotator Tool fits '07-'17 Twin Cam & '06 Dyna Glide Models Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 976 Engine Rotator Tool fits '55-'06 Big Twin Models (Except '06 Dyna Glide) Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 956 Replacement Sleeve Timken Case Bearing Tool Features: Sleeve is several times stronger than stock aluminum case material that standard bearings ride in Replacement sleeve kit for Timken® Case Bearing Tool Made in the...

Jims - 933 Thread Chaser Tap Set Features: An inexpensive way to clean up threads on frames or other parts that have been powder-coated or painted Includes coarse sizes; 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13, and 9/16"-12 Not for cutting...

Jims - 915 Installation Inner Ball Bearing Tool fits '00-'17 Twin Cam “B” Motors Models Features: Accurately and safely install the inner balancer bearing mounted in the left engine case All done on a work bench without using an arbor...

Jims - 916 Case Support Blocks fits '00-'17 Twin Cam Models “B” Motors Features: Aluminum blocks have inserted Delrin® pads that rest against case to prevent marring and to support the case Keeps case level when using bearing pullers...

Jims - 1278-3 Camshaft Bearing Installation fits '99-'17 Twin Cam Models Features: Replacement drive for JIMS® Cam Bearing Installation Tool

Jims - 782 4-Stroke Dual Gauge Leakdown Tester Features: Tool troubleshoots cylinder leakdown issues such as valve seat issues, bad rings and bad head gasket Hose assembly has both 14 mm and 18 mm spark plug threads Includes 12 mm and 10 mm...

Jims - 780 Seal Leak Tester Tool fits '00-'17 Twin Cam “B” Motors Model Features: Required to seal the oil passage way from right case to the balancer tensioner plate; leaking can cause over oiling of the lower end that decreases...

Jims - 1090 Mini Valve Spring Tester Features: Tool fits any dual rate or conical valve spring with an O.D. no larger then 1.6” diameter Works with bench vise, arbor, screw hydraulic or drill press 0 to 1000 P.S.I. gauge Made in the U.S.A.

Jims - 902 Blue Motor Stand fits '00-'17 Twin Cam “B” Motor Model Features: Makes working on motors easier with better access Made in the USA Note: For Twin Cam "B" motor.

Jims - 941 Slim Oil Filter Wrench Features: An exclusive design makes it much easier to navigate when working near both the oil cooler and the crankcase position sensor Allows you more room to work around exhaust pipes, frame, hoses and...

Jims - 3200 Flange Piston Ring End Gap Tool for H-D 95”,103” & 110” Motors w/ Standard Size Pistons (3.875” or 4” Bore) Features: This tool makes measuring ring end gap faster, more accurate and eliminate the guess...

Jims - 746 Go-No-Go Hydraulic Tappet Tool Features: Only when the tip fits nicely with no endplay is the tappet properly adjusted, if the tip doesn’t fit, OR if there is up and down endplay, the tappet is out of adjustment After adjusting the...

Jims - 1042-7 Expander Dowel Tool fits All '00-'17 Twin Cam, '00-'22 Sportster & '02-'17 V-Rod Models Features: Removes and installs 3/4", 1", and 25 mm wheel bearings with or without (Anti-Lock Brake System) ABS Made in the U.S.A.

Jims - 1236 Piston Ring Compressor Kit for Sizes From 2 7/8” to 4 3/ 8” - Set Of 6 Features: Fine-tooth ratcheting motion will compress the bands in small increments for accurate compression Will not break or damage rings Made in the U...

Jims - 5800 Flywheel Puller Tool fits '15-'16 Indian Scout Model Features: Eliminates potential damage to the flywheel when used in this application Ensures good and solid engagement when using the puller Made in the U.S.A...

Jims - 5805 Wrist Pin Remover Tool fits '17-'21 M-Eight Models Features: Quickly and easily removes wrist pins from Milwaukee-Eight® engines Adapter part for JIMS® Wrist Pin Tool (PART# DS-196197) Made in the U.S.A.

Jims - 5808 Valve Spring Compression Collar Tool fits '17-'21 M-Eight Models Features: Valve spring collar allows existing compressor to remove smaller valves on M8 engines For use with JIMS® Valve Spring Compressor Tool (PART# DS-196013) Made...

Jims - 5811 Balancer Scissor Gear Tool fits '17-'20 M-Eight Models Features: Holds 2 halves of spring-loaded balancer scissor gear in alignment before removal Bright color reminds technician to remove it before sealing engine case For use on the...

Jims - 5828 Cylinder Head Holder Tool fits '17-'22 M-Eight & All Twin Cam Models Features: Allows you to easily position head for all types of work Use to hold head in vice through spark plug hole For use with Milwaukee Eight engine series Has...

Jims - 5829 Cylinder Torque Plates fits '17-'20 M-Eight 107”, 114” Models Features: Torque plates must be used when boring or honing late-model aluminum cylinders Simulate running stress conditions Come with instructions Made in the U...

Jims - 5830 Left Main Seal Remover Tool fits '17-'21 M-Eight Models Features: For use on Milwaukee Eight series engines

Jims - 775 Removal/Installation Main Seal Tool fits '99-'17 Twin Cam Models Features: Install and remove crank case main seal while the engine is still in the chassis Includes necessary adapters for '88 and '96 Twin Cams Made in the U.S.A.

Jims - 5834 Engine Stand fits '18-'21 M-Eight Softail Models Features: For use on the Milwaukee Eight™ engine series JIMS Milwaukee-Eight® Softail® engine stand is designed to work on all Milwaukee-Eight® Softail engines JIMS...

Jims - 5835 Valve Spring Compressor Tool fits '17-'21 M-Eight Models Features: Once the cylinder is filled with compressed air, the technician can easily rotate the tool and compress the top collar of the valve spring exposing the keepers to remove...

Jims - 5838 Oil Pump Alignment Tool fits '17-'21 M-Eight Engines Models Features: This tool was designed to help the technician assemble the complete cam chest correctly, in a quick and efficient manner The perfect aid for the technician to either...

Jims - 5506 Magnetic Tappet Holder fits all Twin Cam & M-Eight Models Features: Never turn the engine over if the tappet will not spin with your fingers after adjustments were made It is very important that the engine is not rotated while...

Jims - 730 Piston Tester Jet fits '18-'21 M-Eight Softail Models Features: Assists engine rebuilder to clear jet of all assembly lubes; verifies psi number the jet switches to "on" and visualizes spray pattern before cases are sealed Helps determine...

Jims - 732 Topend Hardware Organizer fits '17-'21 M-Eight Powertrain Models Features: Jims has developed a new set of Milwaukee Eight specific hardware index tools to store and organize bolts while parts are disassembled Can be placed on their side...

Jims - 735 Transmission Hardware Organizer fits '17-'21 M-Eight Powertrain Models Features: Jims has developed a new set of Milwaukee Eight specific hardware index tools to store and organize bolts while parts are disassembled Can be placed on their...

Jims - 1073 Cylinder Torque Plates fits '66-'99 Big Twin Models Features: Torque plates must be used when boring or honing late-model aluminum cylinders Simulate running stress conditions Come with instructions Made in the U.S.A.

Jims - 1284 Connecting Rod Holding Tool for Most V-Twin & Buell Blast Applications Features: Holds the rods in place when reaming or honing the wrist pin bushings Made in the USA For most V-Twin and Buell Blast applications.

Jims - 95660-77 4-Speed Seal Driver fits '82-'86 Big Twin Models Features: Optional drivers used in conjunction with main shaft seal tool allow installation of seals Fitment 1986 Harley-Davidson Softail Heritage...

Jims - 1146 Crankshaft Bearing Installer fits '00-'17 Twin Cam “B” Motors Models Features: Designed to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearing Made in the U.S.A...

Jims - 1167 Balancer Shaft/Removal Bearing Tool fits '00-'06 Twin Cam “B” Motors Models Features: Installing portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's bore Pulls the...

Jims - 1169 Compression Release Valve Installation Kit fits Twin Cam Models Features: Installation kit includes fixture, drill bit, spot face bit and thread-tapping tool Simply drill, spot face, tap and install compression release valves Works on...

Jims - 1110 0.105" Camshaft Pinon Gauge Pins fits '54-'89 Big Twin Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 1989 Harley-Davidson Electra Glide Ultra...

Jims - 1111 0.108" Camshaft Pinion Gauge Pins fits '90-'99 Big Twin Evolution Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...

Jims - 2392 Head Bolt Torque Gauge fits all Twin Cam & Evolution Engines Models Features: This accurate gauge allows the measuring of 90° when tightening head bolts Torquing sequence laser engraved on gauge, with instructions Works on all...