Shop By Motorcycle

Jims - 1013-54TB Pin Bushing Installer fits '54-'92 Big Twin Models (OEM #25582-54/73) Features: Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking dowel pin Made...

Jims - 1017-37TB Cam Bushing Installer fits '37-'48 Big Twin Side-Valve Motors, '54-'20 Sportster, '91-'09 Buell Models (Except 1125R) Features: Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit...

Jims - 1030-TS Crank Pin Flywheel Socket fits 'L83-'99 Big Twin Models (OEM #23969-83) Features: Machined for 100% nut-to-socket and drive-end contact Eliminate nut rounding and risk of injury Made in the U.S.A...

Jims - 33071-73 Bearing Race Remover and Installer fits '73-'99 Big Twin, Sportster & Buell Wheels Features: Designed to remove and install bearing cups in cast wheels Use with JIMS® Handle Fitment 1999 Harley-Davidson Super...

Jims - 94660-37A Counter Shaft Sprocket Locknut Wrench fits '36-'06 Big Twin Models (Except '06 Dyna) Features: Removes hex nut from end of main drive gear that secures the rear drive transmission pulley Extra-long two-piece design Made in the...

Jims - 95760-TB Puller Camshaft Bearing fits '58-'99 Big Twin Models (Except Twin Cam) Features: Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with...

Jims - 95760-TP Pinion Bearing Puller fits '54-'99 Big Twin Models Features: Use to remove pinion bushing from cam cover in one easy operation Use with JIMS® Cam Cover Holder Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...

Jims - 95960-52C Clutch Hub Puller fits '36-'90 Big Twin Models Features: Used to remove wet and dry clutch hubs without removing clutch release rod 4 bolts included for dry clutch removal Made in the U.S.A...

Jims - 96780-58A Piston Pin Lock Ring Tool fits Pre-'73 Big Twin & Sportster Models w/ 0.515” ID Wrist Pins Features: Use to install lock ring (Harley-Davidson® No. 22582-52) in piston having .515” inner diameter wrist pins, like...

Jims - 1051 Wrist Pin Bushing Tool fits '99-'06 Twin Cam Models Features: Used to remove and install wrist pin bushings without removing connecting rods from crankcases Comes with instructions Made in the U.S.A...

Jims - 1283 Camshaft Chain Tensioner Tool fits '99-'06 Twin Cam Models (Except '06 Dyna) Features: Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams Also checks spring loads on chain...

LA Choppers - Pinned Hefty Top Clamp fits '99-'23 Big Twin Models w/ 3-1/2 ” on Center Risers & Offset Mounting Holes Features: Fits Hefty handlebars and risers Polished aluminum construction Pinned to prevent movement of handlebars Made...

Custom Cycle Engineering - 47 mm Ultra Chrome 20.88" Fork Tubes fits '21-'24 RA1250/​RA1250S Models (OEM #455005-85) Features: Excellent high-luster mirror finish with the durability of hard chrome Lengths given may not be the exact OEM length Made...

Custom Cycle Engineering - 49 mm Black 28.50" Fork Tubes fits '16-'22 XL1200X/1200XS Models Features: Black Diamond-like carbon coating Lengths given for OEM replacements may not be the exact OEM length Made in the U.S...

Custom Cycle Engineering - 49 mm Hard Chrome Standard 25.875" Fork Tubes fits '18-'23 FLFB/​FLFBS Models Features: Finish is electrolyzed for increased hardness of 55-60 Rockwell Increased hardness for better long-lasting corrosion...

Custom Cycle Engineering - 49 mm Chrome Fork Brace fits '06-'17 FXD Model Features: Original Randy Smith design Manufactured from a solid piece of 6061 T-6 aluminum, then chrome-plated Designed with a compound arch for greater torsional stiffness,...

Custom Cycle Engineering - 49 mm Chrome Fork Brace fits '06-'08 FXDWG, '08-'17 FXDF Models Features: Original Randy Smith design Manufactured from a solid piece of 6061 T-6 aluminum, then chrome-plated Designed with a compound arch for greater...

Custom Cycle Engineering - Steering Damper System fits '99-'07 FLHR/​FLHT/​FLHTCU/​FLHX Models Features: This complete steering damper system stabilizes the front fork and helps prevent front-end wobble Custom-designed 1-1/4" clamp and bracket...

Custom Cycle Engineering - Swingarm Retrofit Kit fits '99-'01 FLT/​FLHT/​FLHR Models Features: Retrofits the improved swingarm from 02-08 Touring models to a 84-01 Touring models No need to alter transmission housing Will require the purchase of a...

Custom Cycle Engineering - Swingarm Retrofit Kit w/ Pivot Shaft fits '99-'01 FLT/​FLHT/​FLHR Models Features: Retrofits the improved swingarm from 02-08 Touring models to a 84-01 Touring models No need to alter transmission housing Will require the...

Custom Cycle Engineering - Radial Brake Caliper Brackets fits '18-'23 FXFB/​FXFBS/​FXLRS/​FXLRST Models Features: One piece brackets for fitment to radial mount calipers for 43 mm fork tubes Has increased feedback and better caliper to disc...

Custom Cycle Engineering - 41 mm Wide Glide Tweek Bar - Chrome Features: Original Randy Smith design As in the good old days with extended front tubes, the need for a tweek bar is here again Vast improvement over the tweek bars used in the 60s and...

Custom Cycle Engineering - Adjustable Engine Mount fits '99-'17 Dyna Models (OEM #47226-93, 47226-99, 47226-90A) Features: Replace stock front engine bracket with custom slotted bracket with alignment lines Allows the rider to dial in the engine to...

Custom Cycle Engineering - Top Stabilizer Link fits '99-'03 Dyna Models Features: Reduces engine vibration and aligns power train Adjustable rubber-isolated design Greatly reduces vibration especially at high speeds Replaces stock link which is...

Custom Cycle Engineering - Engine Equator II fits '09-'16 Touring Models Features: Allows all Dresser riders to correct chassis misalignment, which is impossible to achieve with the stock motor mount Billet aluminum bracket replaces the forged front...

Custom Cycle Engineering - Narrow-To-Wide Glide Wheel Conversion Kit fits '00-'03 Narrow Glide Model Features: Original Randy Smith design Allow the use of narrow glide 19" or 21" wheel (found on FX, FXR, FXD and XL models) to be installed in a 41...

Arlen Ness - Stage 1 Big Sucker Air Cleaner Kit fits '93-'99 Evolution Big Twin Models Features: Kits include backing plate, filter, breather bolts, steel cover and necessary hardware Billet aluminum or steel outer cover, available in black or...

Drag Specialties - 1" TBW Ape Hanger Handlebars for Narrow Glide These handlebars are made from steel tubing and come in three different finishes: chrome, gloss black, or flat black. They are slotted and notched for Throttle-By-Wire applications and are...

Drag Specialties - 1" TBW Ape Hanger Handlebars for Narrow Glide - 18''/ Chrome These handlebars are made from steel tubing and come in three different finishes: chrome, gloss black, or flat black. They are slotted and notched for Throttle-By-Wire...

Drag Specialties - 1" TBW Ape Hanger Handlebars for Narrow Glide - 12''/ Gloss Black These handlebars are made from steel tubing and come in three different finishes: chrome, gloss black, or flat black. They are slotted and notched for Throttle-By-Wire...

Drag Specialties - 1" TBW Ape Hanger Handlebars for Narrow Glide - 10''/ Chrome These handlebars are made from steel tubing and come in three different finishes: chrome, gloss black, or flat black. They are slotted and notched for Throttle-By-Wire...

Biltwell - Tracker Mid Handlebars 7/8" Black/ Dimpled Biltwell has done it again- these low profile Tracker Handlebars look great on just about any motorcycle! Choose from chrome or black, smooth or dimpled depending on what you ride. These are even...

Biltwell - Tracker Mid Handlebars 7/8"- Chrome Biltwell has done it again- these low profile Tracker Handlebars look great on just about any motorcycle! Choose from chrome or black, smooth or dimpled depending on what you ride. These are even lower than...

Legend Suspension - AXEO Front Suspension System fits Harley Touring Models- 49 mm - FLH '17+ This front suspension cartridge kit is available in two different spring rates, Performance or Comfort. The Performance kit is designed with a stiffer spring...

Uni Filter - Air Filter Element fits '86-'89 80” Evolution Big Twin Models (OEM #29259-86) Features: Constructed of a unique, open-cell polyurethane material that allows maximum airflow while still providing superior filtration Made in the...

Uni Filter - Air Filter Element fits '84-'85 80” Evolution Big Twin Models (Except FLT, FLHT (OEM #29259-83A)) Features: Constructed of a unique, open-cell polyurethane material that allows maximum airflow while still providing superior...

Uni Filter - Air Filter Element fits '84-'85 FLT/FLHT Models (OEM #29288-83) Features: Constructed of a unique, open-cell polyurethane material that allows maximum airflow while still providing superior filtration Made in the...

Uni Filter - Air Filter fits '80-'82 FLT, '82-'83 FXR, 'L78-'82 Sportster 1000, 'L78-'84 FX, FL & FLH Models (OEM #29255-78) Features: Constructed of a unique, open-cell polyurethane material that allows maximum airflow while still providing...

Uni Filter - Air Filter fits 'L73-'E75 Sportster 1000 (3” W), 'L75-'76 FX, FL & FLH Models (OEM #29086-73) Features: Constructed of a unique, open-cell polyurethane material that allows maximum airflow while still providing superior...

Uni Filter - Air Filter fits '83-'85 Sportster 1000,  '66-'E73 Sportster 900, 1000, '67-'E75 FX, FL & FLH Models (OEM #29036-72) Features: Constructed of a unique, open-cell polyurethane material that allows maximum airflow while still...