Tools

V-Twin - 16-1812 - Sprocket Flywheel Nut Socket ToolDescriptionJims sprocket flywheel nut socket features a low profile to give 100% nut contact, machined flat at nut receiving end to eliminate...

V-Twin - 16-1809 - Crank Flywheel Nut Socket ToolDescriptionThe Jims flywheel nut socket features a low profile to give 100% nut contact, machined flat at nut receiving end to eliminate rounding off...

V-Twin - 16-1734 - Swingarm Assembly ToolDescriptionThe swingarm assembly tool removes and installs swingarm pivot components. Fits:FXR 1982-1994FLT 1980-2001Additional Information

V-Twin - 16-1672 - Jims Crankshaft Bearing ToolDescriptionThis crankshaft locking tool locks all crankshafts by engaging the pinion shaft splines. This allows removal and torquing of the pinion nut...

4-speed shaft fixture tool features an angle iron construction.Build your own! Fits:FL 1941-1984Additional Information UOM1 - EA

Oil tank tap and die tool set fluted to clean oil line nuts and tank nipples. To fit oil line fitting set. Includes one piece 9/16" x 24 tap and one piece 9/16" x 24 die. Fits: FL 1941-1964 ...

Linkert hand tool tap and die set features a 1/4" X 40 thread and is for linkert carburetors.Sold as a 2 piece set. Fits:FL 1941-1965Additional Information

45 cam cover fixture tool is used to line the reaming on 45 right side cases. Tool is used with appropriate reamers. Fits:G 1941-1973W 1941-1952Additional Information

V-Twin - 16-1287 - Jims Cylinder Torque PlateDescriptionThe Jims torque plate is lasered with correct torquing sequence and will also work on Eagle big bore cylinders. Fits:FLT 1999-2016FLST...

V-Twin - 16-1281 - Jims Crank Shaft GuideDescriptionUse this crank shaft guide to spread pinion bearing rollers while reassembling right side engine case on to flywheel assembly. Fits:FLT...

V-Twin - 16-1279 - Jims TC-88 Inner Cam Bearing RemoverDescriptionThe Jims inner cam bearing remover replaces the inner bearing easily without damage to crankcases and also prevents rollers from...

V-Twin - 16-1276 - Jims TC-88 Wrist Pin Remover ToolDescriptionJims wrist pin remover tool will cut the time it takes to remove and install wrist pins.This remover tool can be easily used by one...

V-Twin - 16-1263 - 1/4 x 24 inch Tap and Die Tool SetDescriptionSet includes a special tap tool used for repairing or is used for repairing or dressing 1/4"x 24 TPI, and the corresponding tap tool...

V-Twin - 16-1199 - Jims M8 FLT Engine StandDescriptionJims M8 FLT engine stand, needed for any powertrain work, is built from .125" steel and powdercoated blue. Fits:FLT 2017-UPAdditional Information

V-Twin - 16-1198 - Jims Fork Cap Installation ToolDescriptionJims fork cap installation tool for use on 49mm forks, allows the installation of the fork tube caps on the motorcycle without removing...

V-Twin - 16-1193 - Jims FLT Inner Primary Shifter Shaft Bushing ToolDescriptionJims FLT inner primary shifter shaft bushing tool easily removes both worn bushings and quickly installs the new...

V-Twin - 16-1190 - Jims M8 Countershaft 1st Scissor Gear Alignment ToolDescriptionEssential for installation of the countershaft 1st scissor gear, this tool ensure that the scissor gear teeth mesh...

V-Twin - 16-1186 - Jims M8 Cylinder Hold Down Nuts KitDescriptionJims cylinder hold down nuts keep the cylinders in place when the heads are removed from the engine. Useful when installing the second...

V-Twin - 16-1182 - Jims M8 Main Bearing Remover and InstallerDescriptionJims main bearing remover and installer tool removes the left and right main bearing without damaging the case, it also...

V-Twin - 16-1181 - Jims M8 Balancer Scissor Gear Alignment Screw ToolDescriptionJims balancer scissor gear alignment screw tool holds the two halves of the spring loaded scissor balancer gear in...

V-Twin - 16-1160 - Neck Race Remover/Installer ToolDescriptionNeck race remover/installer tool is suitable for neck races that are pressed directly into the frame neck forging.Includes the driver...

V-Twin - 16-1052 - Top End Pushrod Compressor ToolDescriptionTool pushes against the top rocker box to allow one hand operation and is for use on 1936-1998 Big Twin and 1957-2003 XL models. Fits:FXR...

V-Twin - 16-1044 - Duo-Glide Rider Tool KitDescriptionEntire tool kit as pictured, fits in the oval tool box on the 1958-1964 FLH models.Jack and base use requires an extended tube on the right side...

V-Twin - 16-1038 - Clutch Hub Nut Wrench KitDescriptionClutch hub nut wrench kit includes a factory style wrench and nut with a Sifton patch. Fits:EL 1936-1940Additional Information

V-Twin - 16-1029 - Jims Transmission Assembly Vise Stand ToolDescriptionJims transmission assembly vise stand tool is used to assist in the assembly of the transmission gears and shafts.This tool...

V-Twin - 16-0976 - Piston Ring GrinderDescriptionThe piston ring grinder accurately sizes end gap on any piston ring by rotary filing. Fits:All modelsAdditional Information

V-Twin - 16-0877 - Jims Mainshaft Bearing Race ToolDescriptionThis mainshaft primary bearing race remover and installer is used on all 1984-up Big Twins Fits:FXD 1991-2005FLST 1986-2006FLT...

V-Twin - 16-0846 - Rider Tool Kit for 1977-1984 XLDescriptionRider tool kit for 1977-1984 is supplied in a tool roll. The entire kit fits individually in a kidney shaped tool box.Tool kit includes a...

V-Twin - 16-0776 - Wrist Pin Bushing Rod Clamp Tool SetDescriptionWrist pin bushing rod clamp tool set. Fits:G 1936-1973EL 1936-1952FL 1941-UPW 1936-1952Additional Information

V-Twin - 16-0681 - Jims Primary Locking Bar ToolDescriptionJims primary locking bar tool is used to lock the primary for service work on FXR, FLT and FLHT models. Fits:FXR 1982-1994FLT...

V-Twin - 16-0668 - Jims Timken Bearing Race Installer ToolDescriptionJims Timken bearing race installer tool is used when installing bearing races in the left crankcase.Use this tool to press in...

V-Twin - 16-0666 - Jims Hard Cap ToolDescriptionJims hard cap tool protects shaft when using press. Fits:FXD 1991-2017FX 1971-1984FL 1955-1984FLST 1986-2017FXST 1984-2017FLT 1979-UPAdditional...

V-Twin - 16-0657 - Jims Wheel Hub Nut Wrench ToolDescriptionJims wheel hub nut wrench tool is used to remove and install the slotted lock nut to the correct torque on the spoke wheel. Fits:FL...

V-Twin - 16-0586 - Crank Truing MachineDescriptionTruing machine features cast iron construction and is designed to true stock style flywheels.For fork tube straightness checking, you must order the...

V-Twin - 16-0583 - Wheel Bearing Puller/Installer ToolDescription25mm wheel bearing removal head kit. Fits:FLST 2000-2017FXD 2000-2017XL 2000-UPFXST 2000-2017FLT 2000-UPAdditional Information

V-Twin - 16-0530 - Replacement Threaded Lift RodDescriptionReplacement threaded lift rod is for V-Twin #16-0529, Mini Motorcycle Lift Tool. Fits:All modelsAdditional Information

V-Twin - 16-0458 - Gear Alignment ToolDescriptionOil pump/crankshaft gear alignment tool is used to align the oil pump gear flats with the flats of the crankshaft. For Twin Cam 88" and M8 models.We...

V-Twin - 16-0451 - Oil Filter Wrench ToolDescriptionOil filter wrench tool removes oil filter and drain plug Fits:All modelsAdditional Information

V-Twin - 16-0446 - Cylinder Hold Down Nuts ToolDescriptionCylinder hold down nuts tool are used to hold down cylinders during service. Allows motor to be turned over with heads off. Fits:FLT...

V-Twin - 16-0395 - Cam Chest Alignment ToolDescriptionCut away cover allows technician to align idler and distributor drive gear studs, correctly measure cam shaft play. Tighten idler and drive gear...