Tools

V-Twin - 16-1727 - 1-3/8 inch Lap Head PilotDescription1-3/8" lap head pilot tool, engine type. For Eastern tool only. Fits:FL 1955-1957G 1929-1973Additional Information

V-Twin - 16-1726 - 1-1/2 inch Lap Head Pilot Tool SetDescription1-1/2" lap head pilot tool set is the engine type.Sold as a 4 piece set. *NOTE: For Eastern tool only. Fits:FL 1941-1953EL 1936-1952VL...

V-Twin - 16-1724 - Lap Head PilotsDescription1-1/4" lap head pilot tool is the engine type, for the Eastern tool only. Fits:FL 1956-1969Additional Information

4-speed "88" roller spacer tool is used to mimic the 88 roller spacing setting end play. Fits:FL 1944-1976EL 1936-1952Additional Information UOM

Gasket alignment stud tool set includes two 1/4" x 20 and two 1/4" x 24 threaded studs, with slotted screw head. Install to hold oil pump gaskets in place.Sold as a 4 piece set. Fits:FL 1941-1969EL...

4-speed main drive gear tool hex nut.*NOTE: Must order sleeve separately. Fits:FL 1941-1976EL 1936-1952Additional Information UOM1 - EA

V-Twin compensator sprocket wrench is used to easily install or remove compensating sprockets. Features 1/2" drive. Fits:FL 1955-1969Additional Information UOM

V-Twin - 16-1645 - Sifton Mainshaft Bearing Race ToolDescriptionSifton mainshaft bearing race tool.*NOTE: Replacement parts like the race pusher tube, are available separately. Fits:FXD 1991-2005FLST...

V-Twin - 16-1641 - Backing Washer Puller ToolDescriptionBlack oxide finish backing washer #17 puller tool. Fits:FX 2000-UPFLT 2000-UPAdditional Information

V-Twin - 16-1634 - Mini Air CompressorDescriptionMini air compressor features a compact design to fit inside a saddlebag or car.Includes 2' of hose and end to fill tire valves up to 35 pounds. ...

V-Twin - 16-1615 - Chain Puller ToolDescriptionChain puller tool. Fits:AllAdditional Information UOM1 - EA

V-Twin - 16-1514 - Clutch Compression ToolDescriptionClutch compression tool has adapter included Fits:FLST 1990-2017XL 1991-UPFXD 1991-2017FXST 1990-2017FLT 1990-UPFXR 1990-1994Additional Information

V-Twin - 16-1505 - Sprocket Nut Wrench Tool CollarDescriptionNut lock wrench collar features parkerized finish. Fits:FL 1941-1984Additional Information

V-Twin - 16-1503 - Pingel Wheel Chock with Mounts 21 inch OnlyDescriptionThe wheel chock features quick mounting and removal by sliding in and out of slotted mount pads and secures a motorcycle on...

V-Twin - 16-1405 - Linkert Tool KitDescriptionLinkert tool kit includes 6 special drills with brass knurled handles, 1 idle shot tool, and 1 venturi tool for use on brass linkert carburetor bodies,...

V-Twin - 16-1404 - Linkert Hand Tool Tap 5/16 inch X 32DescriptionLinkert hand tool tap 5/16" X 32 thread. Fits:FL 1941-1965Additional Information

V-Twin - 16-1403 - Linkert Hand Tool Tap 5/16 inch X 18DescriptionLinkert hand tool tap 5/16" X 18 thread. Fits:FL 1941-1965Additional Information

V-Twin - 16-1401 - Linkert Hand Tap Tool 12-24DescriptionLinkert hand tool tap 12-24 thread. Fits:FL 1941-1965Additional Information

V-Twin - 16-1400 - Linkert Hand Tool Tap 10-32DescriptionLinkert hand tool tap 10-32 thread. Fits:FL 1941-1965Additional Information

V-Twin - 16-1392 - Cam Bearing Puller ToolDescriptionCam bearing puller tool removes the inner cam needle bearing #9057, without splitting the cases while preventing the rollers from coming out...

V-Twin - 16-1390 - TC-88 Inner Cam Bearing ToolDescriptionThis four piece tool safely installs the inner cam bearings to the proper depth in the case without damaging bearings.Complete 8 piece tool...

V-Twin - 16-1378 - Shaft Turning ToolDescriptionThis Jims shaft turning tool fits spline or taper on assembled motor and allows engine to be turned over by 1/2" ratchet or impact driver. Fits:FLT...

V-Twin - 16-1375 - Jims Case Bearing Conversion ToolDescriptionUsing the special Jims precision insert, this tool is designed to easily and accurately convert the left side crank roller bearing to...

V-Twin - 16-1371 - Wheel Bearing Installer ToolDescriptionWheel bearing install tool is to be used with 25mm bearing, including ABS and non ABS bearings.*NOTE: Required to use with the wheel bearing...

V-Twin - 16-1368 - Starter Ring Gear Rivet Fixture ToolDescriptionThis tool removes the starter ring gear rivets from clutch shells. Fits:FXD 1991-2005FLST 1990-2006FLT 1990-2006FXST...

V-Twin - 16-1364 - Sprocket Shaft Bearing and Seal Installation Tool AdapterDescriptionThis excellent tool upgrades Jims bearing installer tool for work on fine splined Twin Cam sprocket shafts...

V-Twin - 16-1363 - Main Drive Gear Seal InstallerDescriptionThis tool allows for perfect installation of the main drive gear oil seal on the assembled transmission to its proper depth.The protective...

V-Twin - 16-1362 - Gasket Locator ToolDescriptionThis Jims 3 piece gasket locator tool will properly align the primary cam and transmission end cover gaskets that will prevent misalignment and oil...

V-Twin - 16-1357 - Primary Locking ToolDescriptionThe Jims primary locking tool is used to lock the clutch hub sprocket to the front engine sprocket. It also allows the removal or torquing of clutch...

V-Twin - 16-1356 - Transmission Trap Door Puller ToolDescriptionJims right side drive transmission trap door puller tool removes the access door on all right sided drive transmissions. Fits:FXD...

V-Twin - 16-1354 - Jims Case Splitter ToolDescriptionUse this tool to expertly and safely break the case sealant by pushing apart both halves.This tool bolts to the primary mounting holes with...

V-Twin - 16-1344 - Glide Fork Nut ToolDescriptionGlide fork nut double ended wrench feature a black oxide finish. Used for removing and installing crenulated nuts and dust covers with internal thread...

V-Twin - 16-1297 - Starter Jack Shaft Lock WrenchDescriptionJack shaft lock wrench is zinc plated. This tool is used to hold starter gears on 1991-up Big Twins. Fits:FX 1991-UPFLT 1991-UPFXR...

V-Twin - 16-1296 - Factory Style Wrench SetDescriptionThis eight piece set features exact replicas of tools as available to dealers in the early days. Fits:FL 1941-1984G 1941-1957EL 1936-1952W...

V-Twin - 16-1287 - Jims Cylinder Torque PlateDescriptionThe Jims torque plate is lasered with correct torquing sequence and will also work on Eagle big bore cylinders. Fits:FLT 1999-2016FLST...

V-Twin - 16-1283 - Jims Cam Gear Remover ToolDescriptionThe cam gear remover tool is used to remove the cam gear from the camshaft.The tool acts as a stable base to keep the camshaft perpendicular to...

V-Twin - 16-1282 - Jims Cam Gear Alignment ToolDescriptionThis alignment tool is designed to index the cam gears position while removing on installing the cam gear. You will be able to accurately...

V-Twin - 16-1281 - Jims Crank Shaft GuideDescriptionUse this crank shaft guide to spread pinion bearing rollers while reassembling right side engine case on to flywheel assembly. Fits:FLT...

V-Twin - 16-1280 - Jims Cam Bearing Puller ToolDescriptionThe Jims cam bearing puller tool is used to remove the bearing from the crankshaft and is designed to do this with no slipping or binding...

V-Twin - 16-1279 - Jims TC-88 Inner Cam Bearing RemoverDescriptionThe Jims inner cam bearing remover replaces the inner bearing easily without damage to crankcases and also prevents rollers from...