Electra Glide FLB

Chrome 1/2" hole cup shock stud washers Fits:FL 1965-1984FX 1971-1984XLH 1972-1974Additional Information OEM No.54545-65

Chrome 3/8" hole cup shock stud washers Fits:FX 1971-1984XLH 1972-1974FL 1965-1972Additional Information OEM No.54543-65

Chrome 5/8" hole cup shock stud washers Fits:XLH 1965-1974FX 1971-1972FL 1965-1972Additional Information UOM10 - PK

Lower rear shock stud kit includes four cup washers and two studs. Fits:FL 1967-1972FX 1971-1972Additional Information OEM No.54517-67

Upper rear shock stud kit includes four cup washers and two studs. Fits:FL 1967-1972Additional Information OEM No.54515-67

H-12 battery cast is plastic as original battery, with a removable top. Kit features a mock plastic top that will house most smaller batteries and mounts like an original battery.Mock battery box is...

H-12 battery top cover with terminals. Fits:FL 1965-1984XL 1967-1978Additional Information UOM1 - EA

Battery top set is a six piece set. Fits:FL 1965-1984Additional Information UOM6 - SET ManufacturerV-

V-Twin - 53-0501 - 12 Volt AGM H-12 Sealed Battery BlackDescriptionAbsorbed Glass Mat technology proposes the best balance between cold cranking amps and amp hour capacity.AGM battery is fully sealed...

16" x 3.00" front or rear KH style wheel assembly includes a black hub, zicad plated spokes and a black rim.*NOTE: Zicad is a dull shade of zinc similar to cadmium. *NOTE: All spokes...

Chrome 18" X 2.15" steel wheel rim features a full roll edge with weld in side.Rim features a rolled inner seam, features a bead construction with a width of 2.20". Valve stem center hole measures 8...

16" X 3.00" wheel assembly includes chrome hub, rim and stainless steel spokes.This wheel assembly also includes lock screw, seal spacer, tube spacer and one bearing. The hub must be supported by a...

Replica black powder coated front or rear 18" X 2.15" steel wheel rim. This is a WM type rim with welded beaded construction.Features conventional bead construction with a bead width of 2.20". ...

16" X 3.0" front or rear wheel assembly includes black hub, chrome rim and 40 zicad plated spokes.*NOTE: Zicad is a dull shade of zinc similar to cadmium. This wheel assembly also...

V-Twin - 52-0300 - 16 inch x 3 inch Wheel Rim and Spoke Kit Chrome SteelDescriptionRim and spoke set include 16" x 3" front rim with 40 chrome spokes with 40 spoke nipples.For use with a steel hub...

Replacement tank mounts can be used on Fat Bob tanks and also on custom frames where the mounts do not exist. Fits:FL 1955-1984Additional Information UOM

V-Twin - 51-1955 - Replica inchHM inch Straight Leg Rigid FrameDescriptionReplica "HM" straight leg rigid frame is an authentic reproduction of the 1954-1957 straight leg frame with stock 30  neck...

Weld-on brake tab features a raw finish. Mounts stock or replica frames to the rear drum brake backing plate. Fits:FL 1958-1972Additional Information UOM

Engine mount shim is used to raise motor for front or rear clearance, when necessary.Sold in a pack of 5. Fits:FL 1941-1999EL 1936-1952Additional Information

Engine bar features 1" tubing and a black finish.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very slow...

Replica swingarm frame is our authentic reproduction of FLH style to accept a Panhead or Shovelhead engine, 4-speed transmission, seat post, and accepts a round or square swingarm. All components are...

Replica swingarm frame is an authentic reproduction of FLH style for 1965-1984.Frame accepts Panhead or Shovelhead engine, 4-speed transmission, 12v battery and round swingarm for drum brake...

Raw frame swingarm features forged axle plates for 3/4" axle with round tube construction. Fits:FX 1971-1972FL 1958-1972Additional Information OEM No.

This replica authentic style frame neck web repair section must be welded in after cutting stock or custom frame. It features the right side lock housing.Order new lock assembly, separately. Fits:FL...

Engine bar set features left and right sides.Two piece set. **WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while...

Chrome front engine bar features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low...

Engine bar features 1" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very slow speed slide). They...

Frame top engine mount is two halves with seat tee and rear tank mounts incorporated into the top mount.Weld in place for accurate restoration. ...

Rigid hardtail frame raw steel rear section is 1957 style replica construction with components featuring the factory details of the period.The rear transmission mounts are 2" from the bottom cross...

Replica rear hardtail frame section is duplicated from an original rigid frame of 1957. Left axle plates are forged steel as OE. Weld-on type. The axle slots are 7/8" on both sides.Full replica...

Chrome finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications.Lowers bike 1/2"...

Neck frame with hallmarks forged in place. Machined to accept neck lock tumbler.Milwaukee forged neck is accomplished in 4 stages: First the steel is fired as red hot ingot, next huge hammers compact...

Lower frame gas tank mount set is without cross bracket. It includes the right and left tabs. Tabs are constructed of st eel and have a raw finish.May require finishing prior top installation and...

This 5th Mount transmission frame repair tab is weld on style for stock frames. The tab is constructed of steel and has a raw finish.May require finishing prior to installing. Fits:FX 1971-1984FL...

Rear pipe frame tab. Fits: FL 1958-1984 Additional Information UOM 1 - EA Manufacturer V-Twin

Brake line tee tab. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA Manufacturer

Cable mount frame tab is for under tank. Fits:FL 1955-1972Additional Information UOM1 - EA Manufacturer

Upper shock frame mounts are weld on style for stock frames.Sold as a set of two. Fits:FL 1965-1984FX 1971-1984Additional Information UOM1

Casting top seat mount is for frame seat post, frame back bone and frame upper seat rail yoke. Fits:FL 1958-1984Additional Information UOM1 - EA

This weld on style coil mount frame block set repairs stock frames and has a 3/8"-24 UNF thread. Fits:FL 1956-1983FX 1971-1983Additional Information UOM<