Electra Glide FLB

York electric starter kit. Fits:FL 1958-1984Additional Information UOM1 - KIT ManufacturerV-Twin

Kit includes an updated 1.4kW hitachi type black high torque starter and all related components as shown.*NOTE: When fitting to FLH models, a FXE battery will be required to fit FXE battery. Fits:FL...

2020 new production replica dimmer switch with cloth covered wires.Switch may be painted if desired. Fits:UL 1937-1948VL 1930-1934FL 1941-1971EL 1936-1940WL 1929-1952J 1926-1929Additional Information

Dimmer switch rebuild kit replaces the inter components of the switch.Includes a dimmer switch lever, brass plate backlite insulator, contact base, brass contact, rivets and spring. Fits:UL...

Magneto top cover features a red finish and comes with a key. Fits:FX 1971-1980FL 1955-1980Additional Information UOM1 - EA

Magneto drive gear set is for use with Burkhardt magneto drive assemblies. Fits:FL 1970-1992Additional Information UOM1 - SET

Builders wiring harness kit features plastic wires in original factory color codes in vinyl loom with terminals installed.Builders kit includes handlebar, tail lamp, coil and regulator wires. Fits:FL...

This V-Fire Tuneable Ignition Advance Assembly includes a st ainless advance base, points plate with "Blue Streak" points , and condenser with hardware.Three pairs of color coated springs are also...

Directional switch is a three position type with three cloth covered wires. Includes one each of green, red, and black wires and chrome plated housing.Switch features bottom exit wires, and stainless...

Turn signal wiring harness kit has PVC covered wires. Fits:FL 1970-1984Additional Information UOM1 - KIT Manuf

V-Fire ignition kit is single fire and includes mechanical advance unit, hardware, and wiring instructions.Black wire is for the front and the white wire is for the rear. Order coil separately...

V-Fire dual fire ignition kit includes a mechanical advance unit and all hardware.Ignition kit is dual fire where there are two sparks at the same time. Critical wiring instructions are included...

Battery cable is 6 gauge with 13/32" and 11/32" hole sizes on heat shielded terminal ends.PVC plastic coated cable replaces original with heat shielded terminal ends. Use for ground post. Fits:FL...

Starter is 1.4kW unit that generates more power and shaft speed than the original type 0.8kW starter.Starter includes housing to mount to 1965-1978 Big Twin. Unit is Presolite high output type...

V-Fire ignition advance unit features stainless steel base, heat treated weights, and cam center screw for 1970-up mechanical advance ignition. Fits:FX 1971-1978FL 1970-1978XL 1970-1978Additional...

Auxiliary seat spring frame cross stud with spacer. Fits:FL 1958-1984Additional Information OEM No.52605-65 UO

Auxiliary zinc seat spring kit with chrome springs, brackets, nut set, and buddy seat spring bar.Kit adapts to all plunger mounted buddy seats for extra weight capacity. Fits:FL 1965-1984Additional...

Auxiliary seat spring yokesSold in a quantity of 2. Fits:FL 1965-1984Additional Information OEM No.52596-65

Auxiliary seat spring bracket catch set.Sold in a quantity of 2. Fits:FL 1965-1984Additional Information OEM No.52586-68

Auxiliary buddy seat spring bar. Fits:FL 1965-1984Additional Information OEM No.52566-65 UOM1 - EA

Auxiliary spring buddy seat bracket set. Fits:FL 1965-1984Additional Information OEM No.52583-68 UOM1

Chrome 9" rear mount bar for rear turn signals.The distance between the mounting holes measures 5-3/16" center to center. Fits:FL 1963-1973Additional Information

Zinc plated carburetor upper and lower support bracket with hardware kit is for fitting a CV carburetor to a 1948-1985 Big Twin motor. Kit is used to mount motor case bolt between cylinders.This 2...

Black seat bracket kit includes seat bracket, right and left bracket. Fits:FXE 1966-1984FLH 1958-1984FXR 1982-1983FX 1966-1984FL 1958-1984FX 1980-1984Additional Information

Chrome top maxi engine mount has a two piece and two bolt construction for secure fastening. Fits:FX 1971-1984FL 1948-1984Additional Information UOM

Solo seat hardware kit includes nose bracket, chrome springs and rear brackets to mount small type solos.Includes a bracket and 2 thick spacers for the use on 1982-1985 FX models.The thick spacers...

Zinc front solo seat mount bracket bolts to frame holes above seat post tube. The seat nose bracket will swivel on this mount.This bracket will also mount to frames with a flat triangular plate at...

Stainless steel windshield molding clamp set to attach top to center of beaded shields. Sold in a pair.Sold in a quantity of 2. Fits:FL 1969-1984Additional Information

Chrome clamp set for turn signal mounting kit.Sold in a quantity of 2. Fits:FL 1968-1984Additional Information OEM No.68795-68

Seat bracket set features a black finish and includes a zinc clip. Fits:G 1951-1973FL 1965-1967FL 1968-1984Additional Information UOM1

Zinc plated air cleaner mount bracket. Fits:FL 1966-1972Additional Information OEM No.29027-66 UOM1 -

Carburetor support with a zinc finish is for use on OKO and S&S "E" carburetors.For Big Twin models, mounts to center case bolt and carburetor to manifold bolt. Fits:FLST 1985-1999FX 1971-1984FL...

Carburetor support bracket is natural aluminum and measures 5-5/8" center to center. Bracket is used for Shovelhead and EVO applications. Fits:FX 1973-1984FL 1966-1984Additional Information

Steel exhaust repair port is to be welded on broken or damaged heads. Pipe flange is steel and is to repair shovel pipe ends.Sold in a quantity of 2. Fits:FX 1971-1984FL 1966-1984Additional...

Black left side muffler support. Fits:FL 1958-1984Additional Information OEM No.65318-59B UOM1 - EA

Black right side muffler support is for over under drag pipes. Fits:FL 1958-1984Additional Information OEM No.65318-58A

V-Twin - 31-2013 - Rear Seat Tab Stainless SteelDescriptionRear seat tab features a stainless steel finish.For use on tuck and roll seat by Corbin Gentry. Fits:FL 1965-1984FX 1971-1984Additional...

Heavy cast steel construction top motor mount is unbreakable featuring a chrome finish.Thread hole is 5/16" x 18 to mount coil or other accessories, and the distance measures 2" center to center. ...

Heavy cast steel construction top motor mount is unbreakable featuring a zinc plated finish.Thread hole is 5/16" x 18 to mount coil or other accessories, and the distance measures 2" center to center...

2023 New Prodcution coil mount bracket kit features a black finish. Kit includes bracket, reinforcement plate, bolt set and coil mount hardware.Order mount stud set seperately. Fits:FX 1971-1984FL...