Electra Glide FLH

Rigid frame front oil tank mount casting to be welded on.Thread is 5/16 x 24 and the lip from the bottom to the top measures 1-1/4". For use with 1-1/2" bar. Fits:FL 1941-1984FX 1972-1984EL...

Rear frame engine mount and front transmission mount. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA

Rear tank frame mount tabs. Fits:FL 1941-1984EL 1936-1947U 1937-1948Additional Information UOM1 - SET

Weld on frame footpeg mount without thread.Mount can be welded to 1958-1977 swingarm frames to utilize the stock FXE mount and raise the peg position. Sold as a pair. Fits:FX 1971-1978FL...

Replica rear hardtail frame section is duplicated from an original rigid frame. Weld-on type and does not have seat post bushing.The rear transmission mounts are 1-1/2" tall. This hardtail includes...

Beaded windshield is a fixed mount type which comes completely assembled.Includes beaded windshield top and an adjustable lower windshield to fit FL aluminum headlamp cowl assembly. The center bolt...

Top beaded windshield measure 18" and is for use on fiberglass fairings only.Fits 1969-1984 FLH 4 speed and 1980-1985 FLT 5 speed models with Batwing fairings. Fits:FLT 1980-1985FLH...

Top beaded windshield is short style. Fits:FLH 1949-1984Additional Information OEM No.58020-49A UOM1

Frame saver mounting kit for gas tanks must be welded to Big Twin stock or custom frames. Casting features provision for damper pin, as required on 1949-1984 Big Twins.*Note: Includes speedometer...

Replica wishbone frame is an authentic reproduction of a 1948 Big Twin rigid frame with seat post, axle, and transmission plate already installed. The legs are smooth and do not have horn mount...

Solid steel frame dowel set is for the installation of hardtails.Outer diameter on small end is .7225 and large end is .8375. *NOTE: Must be welded in place. Fits:FL 1958-1984Additional Information

V-Twin - 50-2064 - Lindby Custom Front Engine BarDescriptionFront engine bar feature 1-1/8" tubing with built in O-rings on the footpeg area.Front engine bar is constructed of a high strength steel...

Raw alignment clips are for hinged rear fenders, to be spot welded on the front portion of the fender.Sold as a pair. *NOTE: Used to align and hold the rear tail flap edges in place. Fits:FLH...

Swingarm rear fender hinge features a raw finish. Hinge includes both halves with pin but without wire loom tail.Hinge halves are produced with correct pin and hinge offset for installing on original...

Raw steel wire loom fender strip for inside of the left FL rear hinged fender, radiused to fit the fender contour, and segmented to accept tail lamp wires.Must be spot welded to the left side or...

Wire loom spring clamp features a raw finish and is for use with the rear fender. To hold spring loom cover in place use #32-2036. Clamp is sold in a pack of 5.*NOTE: Must be spot welded on. Fits:FL...

FL fender strut set features a chrome finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. The distance from the...

FL fender strut set features a black finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. *NOTE: Requires 7-1/4"...

V-Twin - 50-1148 - Zinc Plated Fender BracketDescriptionZinc plated steel bracket used to adapt one piece FXDF front fenders to fit FLH forks on 1949-up 41mm models.Set of two. Bracket is formed from...

Chrome rear fender strut set is of solid steel construction and is for use with Bobbed fender only. Fits:FX 1973-1984FL 1958-1984Additional Information U

V-Twin - 10-0003 - S&S Stock Bore Shovelhead Engine Crankcase SetDescriptionCrankcase set comes ready to assemble.S&S Crankcase Sets are shipped set-up with Timken left side bearing and race...

Drag Specialties - DS324116 - Battery Top Cover - '65-'84 FLHFeaturesChromed replacement battery top cover fits precisely and features vibration-absorbing cushionsSpecs

Drag Specialties - DS317462 - Battery Strap - '70-'84 FL/FLHFeaturesHigh-quality replacement battery strapsMeets or exceed OEM specificationsSpecs

Drag Specialties - DS310040 - Shock Top Cap - Chrome - '58-'64 FLFeatures3/8” longer than stock for a better fitCome with polished stainless steel clamps, screws and nutsFor all swingarm Harleys with...

Drag Specialties - DS246010 - Rocker Oil Line Set - Chrome - ShovelheadFeaturesChromed steel overhead oil line set includes crossover line and crankcase-to-rocker box lineComplete with fittings and...

Drag Specialties - DS243874 - 5" MPH FL-'36-'40 Style 1:1 Speedometer - White FaceFeaturesSpeedometers have 5/8"-18 threadSpeedometers include reset knob, unless notedMileage cannot be reset on...

Drag Specialties - DS243883 - 5" MPH FL-'62-'67 Style 1:1 Speedometer - Black FaceFeaturesSpeedometers have 5/8"-18 threadSpeedometers include reset knob, unless notedMileage cannot be reset on...

Drag Specialties - DS243817 - Mounting Kit for FL-Style SpeedometerFeaturesUsed for mounting speedometers found in cast dashesKit includes rubber grommets, pins and clipsReplacement Part for OEM...

Drag Specialties - DS240360 - Fork Boots - 41 mm - FL/FLH '48-'77 (Early)FeaturesMolded rubber constructionReplacement Part for OEM Number(s):4598373Specs

Drag Specialties - DS240215 - Long Clutch Lever Rod End - '36-'78 FLFeaturesRod end for long "mousetrap" clutch lever rodReplacement Part for OEM Number(s):3691636Specs

Drag Specialties - DS222777 - Steering Stem Bearing Adjusting Nut - '49-'17 BT Features Steering stem bearing adjusting nut Replacement Part for OEM...

Drag Specialties - DS195054 - Swingarm End Cap Adjusters - '73-'86 Big TwinFeaturesFeatures die-cast construction with highly chromed finishDelivers increased rear axle adjustmentFits models with...

Drag Specialties - DS190681 - Bolt Set - Lifter Base - Smooth/Socket-Head - '36-'76 Harley-DavidsonFeaturesReplacement bolts for lifter baseMade in the USASpecs

Drag Specialties - 24020162 - Cover - Bolt - Deep - Hex - BlackFeaturesDesigned to fit stock-style, 3/4" front axles with 7/8" head and 1/2" hex nut (3/4" wrench size)Attach with silicone (silicone...

Drag Specialties - 24010850 - Board Mount Screws with Nuts - FrontFeaturesHas all required hardware for mounting driver floorboards to the mount bracketsIncludes four shouldered bolts and four...

Drag Specialties - 21130669 - Black Battery Cable Set - '65-'84 FLFeaturesBlack cable manufactured with pure electrolytic-grade, 36-gauge tinned copper strands for maximum current transfer and...

Drag Specialties - 21130216 - Battery Kit - CHD4-12FeaturesMSDS Migration DataDrag Specialties Conventional batteries are built to the same exacting specifications and quality-control standards as...

Drag Specialties - 21130298 - Battery Cover - Smooth - ChromeFeaturesFeatures precise formed covers for sealed and conventional batteriesThe use of AGM sealed maintenance-free batteries requires...

Drag Specialties - 21121204 - 32A Charging Kit - Black RegulatorFeaturesKit includes an encapsulated magnetic rotor, precision-wound stator and an 89-99 32A chrome voltage regulatorFeatures a thick ...

Drag Specialties - 21120927 - Regulator Mount - Harley Davidson - BlackFeaturesAllows the regulator to be mounted down and back out of sightOptional 10-24 holes on back of mount for ground wireMade...