1979

Engine bar set features left and right sides.Two piece set. **WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while...

Engine bar features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide)...

Engine bar features 1-1/4" tubing.This engine bar is not for use with extended forward controls. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection...

Rigid hardtail frame raw steel rear section is 1957 style replica construction with components featuring the factory details of the period.The rear transmission mounts are 2" from the bottom cross...

Raw finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications. Swingarm is for use...

Replica rear hardtail frame section is duplicated from an original rigid frame of 1957. Left axle plates are forged steel as OE. Weld-on type. The axle slots are 7/8" on both sides.Full replica...

Chrome finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications.Lowers bike 1/2"...

This raw steel full rear section hardtail for Sportsters includes the rear motor mount and 4 bolt plate mount with upper and lower tube set. Frame is used to replace the stock rear motor mount and...

Lower frame gas tank mount set is without cross bracket. It includes the right and left tabs. Tabs are constructed of st eel and have a raw finish.May require finishing prior top installation and...

This 5th Mount transmission frame repair tab is weld on style for stock frames. The tab is constructed of steel and has a raw finish.May require finishing prior to installing. Fits:FX 1971-1984FL...

Rear pipe frame tab. Fits: FL 1958-1984 Additional Information UOM 1 - EA Manufacturer V-Twin

Brake line tee tab. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA Manufacturer

Upper shock frame mounts are weld on style for stock frames.Sold as a set of two. Fits:FL 1965-1984FX 1971-1984Additional Information UOM1

Casting top seat mount is for frame seat post, frame back bone and frame upper seat rail yoke. Fits:FL 1958-1984Additional Information UOM1 - EA

Frame mount tab set for solo seats have weld on mount tabs. Use with T bar and pivot bolt to mount K and CH solos. Fits:XL 1957-1979Additional Information UOM

This weld on style coil mount frame block set repairs stock frames and has a 3/8"-24 UNF thread. Fits:FL 1956-1983FX 1971-1983Additional Information UOM<

Rigid frame front oil tank mount casting to be welded on.Thread is 5/16 x 24 and the lip from the bottom to the top measures 1-1/4". For use with 1-1/2" bar. Fits:FL 1941-1984FX 1972-1984EL...

Rear frame engine mount and front transmission mount. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA

Rear tank frame mount tabs. Fits:FL 1941-1984EL 1936-1947U 1937-1948Additional Information UOM1 - SET

Weld on frame footpeg mount without thread.Mount can be welded to 1958-1977 swingarm frames to utilize the stock FXE mount and raise the peg position. Sold as a pair. Fits:FX 1971-1978FL...

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

Replica rear hardtail frame section is duplicated from an original rigid frame. Weld-on type and does not have seat post bushing.The rear transmission mounts are 1-1/2" tall. This hardtail includes...

Beaded windshield is a fixed mount type which comes completely assembled.Includes beaded windshield top and an adjustable lower windshield to fit FL aluminum headlamp cowl assembly. The center bolt...

Top beaded windshield measure 18" and is for use on fiberglass fairings only.Fits 1969-1984 FLH 4 speed and 1980-1985 FLT 5 speed models with Batwing fairings. Fits:FLT 1980-1985FLH...

Top beaded windshield is short style. Fits:FLH 1949-1984Additional Information OEM No.58020-49A UOM1

Frame saver mounting kit for gas tanks must be welded to Big Twin stock or custom frames. Casting features provision for damper pin, as required on 1949-1984 Big Twins.*Note: Includes speedometer...

Replica wishbone frame is an authentic reproduction of a 1948 Big Twin rigid frame with seat post, axle, and transmission plate already installed. The legs are smooth and do not have horn mount...

Solid steel frame dowel set is for the installation of hardtails.Outer diameter on small end is .7225 and large end is .8375. *NOTE: Must be welded in place. Fits:FL 1958-1984Additional Information

Arm chair sissy bar for Sportster models features a black finish.Original "arm chain" design from 1977, developed by Ron Thiese at SMC ACCU Weld in Palmer, MA. Fits:XLS 1979-1982Additional Information

FL fender strut set features a chrome finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. The distance from the...

FL fender strut set features a black finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. *NOTE: Requires 7-1/4"...

V-Twin - 50-1148 - Zinc Plated Fender BracketDescriptionZinc plated steel bracket used to adapt one piece FXDF front fenders to fit FLH forks on 1949-up 41mm models.Set of two. Bracket is formed from...

Tool box kit includes chrome oval tool box with 2 keys, zinc plated mount bracket and liner.Bracket will mount tool box on left side in rear of outer primary cover. Fits:FX 1977-1984FL...

Chrome rear fender strut set is of solid steel construction and is for use with Bobbed fender only. Fits:FX 1973-1984FL 1958-1984Additional Information U

V-Twin - 50-0625 - XL Rigid Tool Box KitDescriptionLeft side tool box kit is the weld on type for rigid frames on Sportster builds.*NOTE: Weld bracket to lower rigid frame hardtail tube position or...

V-Twin - 10-0003 - S&S Stock Bore Shovelhead Engine Crankcase SetDescriptionCrankcase set comes ready to assemble.S&S Crankcase Sets are shipped set-up with Timken left side bearing and race...

Drag Specialties - DS324116 - Battery Top Cover - '65-'84 FLHFeaturesChromed replacement battery top cover fits precisely and features vibration-absorbing cushionsSpecs

Drag Specialties - DS317468 - Battery Strap - '73-'86 FX / '82-'97 XLFeaturesHigh-quality replacement battery strapsMeet or exceed OEM specificationsReplacement Part for OEM...

Drag Specialties - DS317465 - Battery Strap - F/'80-'92 FLT Features High-quality replacement battery straps Meet or exceed OEM specifications Specs

Drag Specialties - DS317462 - Battery Strap - '70-'84 FL/FLHFeaturesHigh-quality replacement battery strapsMeets or exceed OEM specificationsSpecs