Super Glide FXR

Magnum Shielding - 31270 - Hydraulic Clutch Line - Sterling Chrome II - 70"FeaturesUnique stainless steel transmission fittings eliminate the use of adapters (12-and-older hydraulic clutch line...

Magnum Shielding - 31266 - Hydraulic Clutch Line - Sterling Chrome II - 66"FeaturesUnique stainless steel transmission fittings eliminate the use of adapters (12-and-older hydraulic clutch line...

Magnum Shielding - 36464SW - Brake Line - 90/180  - 64" - Sterling Chromite IIFeatures90/180e-z alignmagnum e-z align90/180Housing length is measured from the center of the banjo hole at the master...

Magnum Shielding - 31170 - Hydraulic Clutch Line - Sterling Chrome II - 70"FeaturesUnique stainless steel transmission fittings eliminate the use of adapters (12-and-older hydraulic clutch line...

Lyndall Racing Brakes Llc - 7059X - X-Treme Brake Pads - Harley-DavidsonFeaturesThese brakes will give you a 0.6 coefficient from ambient to first fade and a 0.6 coefficient from first recovery to...

Lyndall Racing Brakes Llc - 7058-GPLUS - Gold-Plus Brake Pads - Harley-DavidsonFeaturesGold+ runs cooler and has less brake dust than a sintered pad, while also being half the weightIdeal for heavy...

Magnum Shielding - 3030C - Spark Plug Wires - Sterling Chromite - FXRFeaturesBraid perfectly matches all other Magnum cables and brake linesHigh-voltage, high temperature 8 mm silicone ignition wire...

FXR/FLT starter plug for the starter pivot arm. Starter plug is 1/4 inch NPT x 15/32 length x 1/4 inch. Sold in a pack of 5. Instructions: http://www.vtwinmfg.com/Instructions/12/12-1783...

FXR steel shifter lever features a chrome plated finish. Fitment: FXR 1982-1994

FXR stainless steel heel toe shifter lever is a one piece deseign for 5-speed models with mid controls. Includes 2 rubber pads. *NOTE: The distance from the center of the spline to the very end of...

FXR kickstand mount bracket features a raw finish and must be welded in place. Accepts stock kickstand pin and spring. Fitment: FXR 1982-1994

FXE rear exhaust mount kit includes a black bolt on style rear pipe bracket and zinc hardware. *NOTE: The bracket bolts to the pivot bolt hex bolts to replace the weld-on bracket. Fitment: FXR...

Zinc plated FXR front exhaust mount bracket. . Fitment: FXR 1986-1994

FXR horn mount bracket is the later version with a zinc plated finish. Tech Notes: Suggested to use with #33-2116 Replica Replacement Horn Black Fitment: FXR 1984-1994

Exhaust bracket for FXR models features a raw finish. Support bracket is welded to the frame to house the isolator block available separately. *NOTE: Must order hardware separately. Fitment: FXR...

FXR exhaust mount bracket. FXR exhaust mount bracket is mounted with (2) 7/16-20x1* pivot bolt cap screws. Our bracket mounting block can be bolted on to the opposing side using (2) 5/16-24x 5/8...

Battery strap clamp for FXR models features a black finish. Includes nut that is welded in place. Use with 1/4 x 20 bolt 1-1/2 inch hex head and 1/4 x 20 jam nut. Fitment: FXR 1984-1988 FXR 1990-1994

Rear exhaust bracket is zinc plated and for use with FXR models. *NOTE: Must order additional hardware: 5/16 inch x 3/4 inch x 1 inch spacer 5/16 inch-18 x 2 inch and 5/16 inch-18 x 1-3/4 inch allen...

FXR pipe bracket kit includes a raw weld on type bracket and an ISO mount block. *NOTE: Bracket must be welded on. Fitment: FXR 1982-1994

Silver dash panel decal set. Sold as a 2 piece set. Fitment: FXR 1982-1994

Sold as a pair. Fitment: FXR 1982-1994

Rear axle adjuster has a 3/4 inch inner diameter and includes heavy pull blocks and two 1/4 inch-20 x 2 inch full thread allen cap screws. Fitment: FXR 1982-1994

Side cover for a 5-speed transmission clutch features a black finish. Fitment: FXR 1987-1994

WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped very low speed slide). They are not made nor intended to...

FXRP footboard control kit includes a brake pedal chrome footboard set zinc plated frame mount brackets and a heel-toe shifter lever. Fitment: FXR 1982-1994

FXR brake plunger kit is a three piece kit that includes a plunger rod end brake plunger end and hex nut in a zinc finish. Fitment: FXR 1987-1994

FXR shifter shaft bushing includes 4 o-ring alloy type with two bronze bushings on each end. Sleeve is used to replace the stock plastic part. Fitment: FXR 1984-1994

FXR shifter rod assembly features a zinc finish and includes right and left hand ball ends with nuts. For use on FXR mid control shifter installation. Fitment: FXR 1982-1994

FXR driver footpeg set features zinc plated peg shafts and includes the rubber set and mount bolt set. Sold as a pair. Fitment: FXR 1982-1994 XL 1986-2004

2023 New Production black kickstand is stock length and includes pin for FXR models. Fitment: FXR 1982-1990

FXR frame side cover set is constructed of black ABS plastic with vented panels. Sold as a pair. Requires (4) 1/4 inch-20 x 1-3/4 inch allen bolts and (4) 1/4 inch flat washers. Tech Notes: Required...

This replaces the original plastic unit on the 1982-up models. Thread is 3/8 inch x 28 TPI. Holes on the back measure starting with the small one closest to the bottom and working to up: #8-32* 5/16...

Pro-One - Steering Stem Bolt fits '99-'05 FXD & '88-'22 Sportster Models (Except RH Sportster) Features: Replaces stock steering stem hardware Note: Replacement for Pro-One Triple Tree...

James Gaskets - JGI-18633-48-KF - Tappet Block Gasket - Fits '48-'99 Big Twin Models (.020” Foamet®) - Pair Fits: '48-'99 Big Twin Models (.020” Foamet®). Full year/model list is on the Fitment tab...

James Gaskets - JGI-16779-99-X - 1 Piece Lower Rocker Housing Gasket - Fits '86-'22 Sportster Models (Except RH Sportster - Pair Fits: '86-'22 Sportster Models (Except RH Sportster. Full year/model...

James Gaskets - JGI-16777-94-S - 3.625" Big Bore Metal Base Gasket - Fits '84-'99 Evolution Big Twin Models - Pair Fits: '84-'99 Evolution Big Twin Models. Full year/model list is on the Fitment tab...

James Gasket - 39 mm Fork Seals fits '99-'05 Dyna, 'L87-'22 Sportster Models (Except RH Sportster (OEM #45378-87)) Features: High-quality replacement components Available in dealer packs of ten...

James Gaskets - JGI-16777-96-X - 4.000" S&S Cylinders Front/Rear Metal Base Gasket - Fits '84-'99 Evolution Models - Pair Fits: '84-'99 Evolution Models. Full year/model list is on the Fitment tab. 4...

James Gaskets - JGI-25225-70-XM - 0.036” Cam Cover Gasket - Fits '70-'92 Big Twin Models (Metal Core, Paper Facing w/ Silicone Fits: '70-'92 Big Twin Models (Metal Core, Paper Facing w/ Silicone...

James Gasket - 9 Hole Rigid Mount Foamet® Primary Cover Gasket fits '65-'88 Big Twin Models (OEM #60538-81, 60538-81A) Features: Top quality gaskets, seals and O-rings meet or exceed OEM...