2001

Jims - 1275 Crankshaft Bearing Tool fits '99-'02 Twin Cam “A” Motors Features: Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in the U.S.A...

Jims - 74437-96 Electronic Speedometer Sensor fits '00-'06 Softail Models (OEM #74430-00, 74430-00D, 74437-96) Features: Top-quality replacement sensor Also works on any aftermarket transmission case with a speedometer sensor hole Includes O-ring,...

Jims - 74420-94 Electronic Speedometer Sensor fits '99-'03 FLT Model (OEM #74420-94, 74429-97, 74429-97A) Features: Top-quality replacement sensor Also works on any aftermarket transmission case with a speedometer sensor hole Includes O-ring,...

Jims - 955 Gauge for Harley-Davidson Injection Pressure fits '01-'20 Big Twin Models w/ Delphi EFI (Except '18-'20 Softails) Features: Includes all necessary parts to diagnose Delphi fuel injection; a large gauge assembly, 8" hose, 2" hose, fuel tank...

Jims - 977 Fork Stem Nut Wrench fits '96-'13 FLHT & '94-'13 FLHR Models Features: This tool allows the ability to loosen, tighten and torque to spec the 1-1/2” stem nut without radio removal Normally to get access to the top stem nut...

Jims - 2232 Bearing Race Tool fits '84-'17 Big Twin (Except '14-'17 Dressers), '86-'22 Sportster & '94-'02 Buell OEM Frames (Will Also Work on Most Aftermarket Frames) Features: Removes and installs steering head bearing race on 84-16 Big Twin...

Jims - 96600-36B Valve Spring Compressor Tool fits '36-'04 Big Twin & '57-'03 Sportster Models Features: Comes with new valve collar receiver for safer tool usage, and can be clamped in vice Hardened ball bearing style tip at valve head end...

Jims - 94547-80B Sprocket Shaft Bearing Race Tool fits '77-'03 Sportster, '94-'02 Buell Models Features: Must use with JIMS® Race and Bearing Install Handle (PART# DS-196042) Used to remove and install Timken® bearing race on motor...

Jims - 97225-55 Sprocket Shift Bearing Installation Tool fits '55-'02 Big Twin Models Features: Used on '84-'02 Big Twin to install the flywheel assembly to the left crankcase Timken® bearing Made in the U.S.A...

Jims - 1743 Swingarm Bushing Tool fits '80-'01 FLT/​FLHT, '82-'99 FXR & all Aftermarket FXR-Style Frames Features: Allows installation of delicate, silicone cleveblock bushings in swingarm without damage Tool presses on outer sleeve of...

Jims - 34731-84 Valve Guide Installer fits all Evolution & '99-'04 Twin Cam Models (OEM #34731-84) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A...

Jims - 1017-37TB Cam Bushing Installer fits '37-'48 Big Twin Side-Valve Motors, '54-'20 Sportster, '91-'09 Buell Models (Except 1125R) Features: Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit...

Jims - 94660-37A Counter Shaft Sprocket Locknut Wrench fits '36-'06 Big Twin Models (Except '06 Dyna) Features: Removes hex nut from end of main drive gear that secures the rear drive transmission pulley Extra-long two-piece design Made in the...

Jims - 1051 Wrist Pin Bushing Tool fits '99-'06 Twin Cam Models Features: Used to remove and install wrist pin bushings without removing connecting rods from crankcases Comes with instructions Made in the U.S.A...

Jims - 1283 Camshaft Chain Tensioner Tool fits '99-'06 Twin Cam Models (Except '06 Dyna) Features: Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams Also checks spring loads on chain...

LA Choppers - Pinned Hefty Top Clamp fits '99-'23 Big Twin Models w/ 3-1/2 ” on Center Risers & Offset Mounting Holes Features: Fits Hefty handlebars and risers Polished aluminum construction Pinned to prevent movement of handlebars Made...

Forbidden Motorcycles - Moto Style Handlebars 1" (1-1/8" Clamping Area) The Forbidden Motorcycles 1" Moto Style Bars feature a 1-1/8" clamping area but taper down to 1" to accommodate stock Harley hand controls, eliminating the need to sleeve them. They...

Custom Cycle Engineering - Steering Damper System fits '99-'07 FLHR/​FLHT/​FLHTCU/​FLHX Models Features: This complete steering damper system stabilizes the front fork and helps prevent front-end wobble Custom-designed 1-1/4" clamp and bracket...

Custom Cycle Engineering - Swingarm Retrofit Kit fits '99-'01 FLT/​FLHT/​FLHR Models Features: Retrofits the improved swingarm from 02-08 Touring models to a 84-01 Touring models No need to alter transmission housing Will require the purchase of a...

Custom Cycle Engineering - Swingarm Retrofit Kit w/ Pivot Shaft fits '99-'01 FLT/​FLHT/​FLHR Models Features: Retrofits the improved swingarm from 02-08 Touring models to a 84-01 Touring models No need to alter transmission housing Will require the...

Custom Cycle Engineering - 41 mm Wide Glide Tweek Bar - Chrome Features: Original Randy Smith design As in the good old days with extended front tubes, the need for a tweek bar is here again Vast improvement over the tweek bars used in the 60s and...

Custom Cycle Engineering - Adjustable Engine Mount fits '99-'17 Dyna Models (OEM #47226-93, 47226-99, 47226-90A) Features: Replace stock front engine bracket with custom slotted bracket with alignment lines Allows the rider to dial in the engine to...

Custom Cycle Engineering - Top Stabilizer Link fits '99-'03 Dyna Models Features: Reduces engine vibration and aligns power train Adjustable rubber-isolated design Greatly reduces vibration especially at high speeds Replaces stock link which is...

Custom Cycle Engineering - Narrow-To-Wide Glide Wheel Conversion Kit fits '00-'03 Narrow Glide Model Features: Original Randy Smith design Allow the use of narrow glide 19" or 21" wheel (found on FX, FXR, FXD and XL models) to be installed in a 41...