2009

Jims - 729 Inner Primary Seal/Bearing Removal/Installation Tool fits '85-'20 Big Twin Models Features: Gives a much better feel than a press while eliminating the possibility of applying too much pressure to the parts Provides precise installation...

Jims - 967-4 Installation/Removal Inner Primary Bearing Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearing Also...

Jims - 967-5 Inner Primary Bearing Tool fits '07-'19 Big Twin & '06 Dyna Models Features: Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearing Also removes and installs...

Jims - 5502 Ultimate Clutch Adjusting Tool fits '85-'20 Big Twins Models w/ Mechanical Clutch Features: Allows the quick and accurate tightening of the clutch adjusting screw jam nut without having the screw change position No more guessing or...

Jims - 5516 Sprocket Nut/Removal/Installation Socket Tool fits '91-'20 Sportster & Buell Models (Except Buell 1125R) Features: Ensures the mainshaft on Harley-Davidson® Sportster models extends through the guidance collar for correct...

Jims - 5517 Removal/Installation Shifter Mechanism Sleeve Tool fits '06 Dyna & '07-'20 Big Twin w/ 6-Speed Cruise Drive Transmission Features: A real time saver for removing and installing the shifter mechanism sleeve in cruise drive Big Twin...

Jims - 5518 Shifter Shaft Bushing Tool fits '85-'16 FLT Touring w/ 5- or 6-Speed Transmission Features: Time-saving tool removes worn shift shaft bushings in Big Twin primaries without having to remove he inner primary Tools installs new bushings to...

Jims - 900 6-Speed Main Drive Gear and Bearing Remover/Installer fits '06-'17 Touring, '06 Dyna & '07-'17 Softail Models Features: Complete kit for servicing the main drive gear or the main bearing on the latest Harley-Davidson­­®...

Jims - 1672 Crankshaft Bearing Tool fits '03-'17 Twin Cam “A” and “B” Motors Models Features: Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in...

Jims - 995 Case Splitter Tool fits '07-'17 Twin Cam & '06 Dyna Models Features: "Breaks" the case sealant by pushing apart both case halves Uses included hand thread-in pushing screw Flywheels will be pushed from the left case Bolts to primary...

Jims - 988 Valve Spring Compressor fits '05-'17 Twin Cam (Except SE Models), '04-'22 Sportster (Except RH Sportster) & Buell Models (Except 1125R) Features: Used to remove and replace valve and new-style conical valve spring Requires use of JIMS...

Jims - 969 Socket O² Sensor Tool fits '06 Dyna Glide & '07-'17 Twin Cam Models (Except 10-17 FLHT/​ FLHR/​FLHX/​FLTR, 11-17 FXST/​FLST/​FXS, 12-17 FXD/​FLD) Features: Remove and install oxygen sensors on fuel-injected models Socket tool...

Jims - 972 6-Speed Main Drive Gear Seal Installer fits all '07-'20 Big Twin & '06 Dyna Models Features: Use to install main drive gear oil seal to the proper depth with transmission assembled Includes protective sleeve for seal, which can be...

Jims - 975 Engine Rotator Tool fits '07-'17 Twin Cam & '06 Dyna Glide Models Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 2049 49 mm Fork Seal Installation Tool fits '06-'17 Dyna, '02-'11 V-Rod Models (Except Inverted Fork Models) Features: Installs lower leg 49 mm fork seals squarely into the bore without damaging the seal lip surface Designed for specific...

Jims - 956 Replacement Sleeve Timken Case Bearing Tool Features: Sleeve is several times stronger than stock aluminum case material that standard bearings ride in Replacement sleeve kit for Timken® Case Bearing Tool Made in the...

Jims - 937 7mm Valve Guide Remover fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125R) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made...

Jims - 938 7mm Valve Guide Installer fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125CR) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve...

Jims - 760K Socket Dipstick Insert Kit fits '07-'11 Touring & '06-'11 FXD Models Features: Simply install this insert in your existing JIMS dipstick socket tool and remove the finger grasp cap easily with no chance of damage This insert,...

Jims - 5506 Magnetic Tappet Holder fits all Twin Cam & M-Eight Models Features: Never turn the engine over if the tappet will not spin with your fingers after adjustments were made It is very important that the engine is not rotated while...

Jims - 5530 Remote Fuel Tank fits H-D Models w/ Delphi Fuel Injection (Except V-Rod) Features: Tank is completely mobile, even when pressurized; canister does not need to be continuously connected to the air supply Small enough to hang from a...

Jims - 5820 Standard Rear Axle Installation Guide Tool fits '08-'21 Big Twin w/ Hollow 1” (25 mm) Features: Aligns wheel with swingarm, caliper brackets, wheel hubs and spacers Made in the USA For Big Twin models with hollow 1" (25 mm)...

Jims - 2244 3/8" 35 mm Fork Nut Socket fits For Big Twin & Sportster Models Features: Used to remove and install top fork nuts on fork tubes Rubber protector inside socket Will clear most handlebars Made in the U.S.A...

Jims - 1146 Crankshaft Bearing Installer fits '00-'17 Twin Cam “B” Motors Models Features: Designed to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearing Made in the U.S.A...

FLHRS Jims - 2043 41mm Fork Nut Socket fits '48-'17 Wide Glide Models Features: Eliminates possible burring of plug caused by wrenches Used to remove and install top fork-tube plug Fits 41 mm forks Made in the U.S.A...

Jims - 1705 Exhaust Drill Plate fits '84-'17 Big Twin (Except M-Eight), '86-'22 Sportster & '94-'09 Buell Models (Except 1125R) Features: Will position the seal evenly into the exhaust port of head Tool can be used with exhaust flange nuts Made...

Jims - 95760-57 Bushing Bearing Puller fits '66-'17 Big Twin (Except M-Eight), '57-'22 Sportster & Buell Models (Except 1125R) Features: Used to remove rocker bushing or bearing in one easy operation Made in the U.S.A...

Jims - 33443-84 Tappet Aligning Tool fits 'L76-'17 Big Twin Models (Except M-Eight) Features: Can also be used to align rocker box bases on Evolution head (requires two tools) Also used in Harley-Davidson® Twin Cam oil pump alignment...

Jims - 2260 Sprocket Lock Tool fits '99-'17 Twin Cam & '80-'99 Big Twin Models w/ Rear Belt Drive Features: Lock the transmission pulley for removing or installing pulley nut Made in the U.S.A...

Jims - 1288 Crankshaft Guide fits '99-'17 Twin Cam & '03-'09 Buell XB9R/X B9S Models Features: Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A...

Jims - 1725 Head Bearing Race Installer fits '36-'17 Big Twin Models w/ Stock or Custom Frames (Except '14-'17 Dresser) Features: Use to install steering head races, stock and custom, as well as install cups in the frame This tool pulls the races...

Jims - 2234 Primary Drive Lock Tool fits '70-'06 Big Twin & '86-'22 Sportster Models Features: Use on all primaries between front primary chain and motor sprocket Made in the U.S.A. Fitment 2016-2017 Harley-Davidson 1200 Roadster...

Jims - 39361-69 Sprocket Shaft Seal Installation Tool fits '69-'10 Big Twin & Twin Cam Models Features: Designed to press oil seal over sprocket shaft into case Made in the U.S.A. Fitment 2010 Harley-Davidson Street Glide Trike...

Jims - 34902-84 Mainshaft Bearing Race Tool fits 'L84-'20 Big Twin Models Features: Used to remove and install the inner bearing race on the transmission mainshaft Made in the U.S.A. Fitment 2016-2017 Harley-Davidson Fat Boy S...

Jims - 95970-32C Piston Pin Bush Tool fits '36-'99 Big Twin, '57-'20 Sportster & Buell Models (Except 1125R) Features: Use to remove and install wrist pin bushings without removing rods from crankcase Made in the U.S.A...

Jims - 955 Gauge for Harley-Davidson Injection Pressure fits '01-'20 Big Twin Models w/ Delphi EFI (Except '18-'20 Softails) Features: Includes all necessary parts to diagnose Delphi fuel injection; a large gauge assembly, 8" hose, 2" hose, fuel tank...

Jims - 954 Pump Ring Tool fits '08-'20 FLHT Model Features: Use for quick and easy service of fuel filter and other fuel-related parts Removes/installs retaining ring holding fuel pump Heavy-duty construction Made in the U.S.A...

Jims - 970 3rd Hand Axle Locker Tool fits '02-'21 FLT/​FLHT Models Features: Eliminates the need for a helper or trying to blindly hold the axle from the other side of the tire Prevents axle from moving while torquing down the axle nut after setting...

Jims - 977 Fork Stem Nut Wrench fits '96-'13 FLHT & '94-'13 FLHR Models Features: This tool allows the ability to loosen, tighten and torque to spec the 1-1/2” stem nut without radio removal Normally to get access to the top stem nut...

Jims - 5822 Swing Arm Bearing Installer fits '02-'21 Touring Models Features: Both drive side and brake side bearings, which are at different depths, can be easily and accurately installed with this tool kit JIMS® took it one step further and...