York 4-speed clutch cable for use with 4-speed kick starter covers.Use with kick starter covers with cable operated ball-ramp clutch release assembly. *NOTE: Uses a small hole perch type handlebar lever assembly. Fits:FX 1971-1984FL 1941-1984Additional...

4 Tooth fine speedometer drive gear featuring a smaller inner diameter than OE.For use with 2:1 ratio speedometer and drive gear. Fits:FL 1962-1968Additional Information UOM1 - EA ManufacturerV-Twin OriginImported Type4-Speed 2025 Catalog Pages535 ...

Speedometer drive gear is for press fit installation onto counter shaft gear featuring a smaller inner diameter than OE.The inner diameter measures 55.54mm. Fits:UL 1937-1948FL 1941-1961EL 1937-1940Additional Information OEM No.35635-36 UOM1 - EA ...

Front wheel brake cable tube clamp is cadmium plated. This is the early longer version of the clamp. Fits:K 1952-1956KH 1952-1956XLCH 1950-1958XL 1950-1958Additional Information OEM No.45218-52 UOM1 - KIT ManufacturerV-Twin OriginUSA 2025 Catalog...

Handlebar to fork cable guide cover is constructed of black plastic. Fits:FL 1949-1960Additional Information OEM No.56600-49 UOM1 - EA ManufacturerV-Twin OriginUSA

Linkert carburetor float pin with caps. Fits:WL 1933-1952UL 1937-1948FL 1941-1965EL 1936-1940VL 1933-1934Additional Information OEM No.27383-11A UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages708

Linkert carburetor choke lever has the ball detent cam included. Fits:WLA 1941-1945W 1941-1952Additional Information OEM No.27288-33 UOM1 - EA ManufacturerV-Twin OriginUSA 2025 Catalog Pages711

Linkert carburetor choke disc with small hole has a 1.665" outer diameter.Lower vent hole is .27" in diameter. Fits:UL 1937-1948WL 1944-1952EL 1936-1947FL 1941-1947Additional Information OEM No.27225-24 UOM1 - EA ManufacturerV-Twin OriginImported ...

Petcock is wing type with zinc finish has a 3/8" NPT and accepts a 5/16" fuel line. Includes screen and 2 handles, sliding control valve with reserve. Fits:FX 1971-1974XL 1955-1974FL 1965-1974Additional Information OEM No.62125-55B UOM1 - EA ...

Type Linkert carburetor float lever is pressed and formed of brass material. Order needle and seat separately.*NOTE: Remove burrs located in slot in order for the needle to move freely inside the arm. Fits:FL 1941-1965EL 1936-1952W 1936-1952Additional...

Overhaul kit for 1-1/2" carburetors includes throttle shaft brass float, needle and seat, float, bushings, springs, float pin, gasket, carburetor bowl large nut with stud, lock washer luck nut, and copper filled seal washer.For M74 models. Threads on...

Replica brass Linkert throttle shaft is for 1-1/2" carburetors and includes a steel bushing set.Fits the following Linkert Carburetors: M-25, M-35T, M-36, M-45, M-45A, M-61, M-74, M-74B, M-75. Fits:FL 1941-1965Additional Information OEM No.27276-40A ...

Linkert carburetor overhaul kit with brass float. Also includes needle and seat, float, bushings, springs, float pin, and gaskets.Threads on this needle and seat assembly is 7/16 x 27. Fits:WL 1933-1952UL 1937-1948FL 1934-1965EL 1936-1940VL...

Replica Linkert carburetor float lever.This linkert float lever is a one piece design, accurate for investment casting, detail and funtion in brass. Fits:FL 1941-1965EL 1936-1952W 1936-1952Additional Information OEM No.27381-50 UOM1 - EA ...

Replica brass Linkert throttle shaft is for a 1-1/2" carburetors.Fits the following Linkert Carburetors: M-25, M-35T, M-36, M-45, M-45A, M-61, M-74, M-74B, M-75. ...

Cadmium Linkert carburetor choke rod is manufactured to meet or exceed OEM specifications for long lasting durability and performance. Fits:FL 1948-1965Additional Information OEM No.27244-48 UOM1 - EA ManufacturerV-Twin OriginUSA 2025 Catalog...

Carburetor choke lever screws for M-18, M-41, M-42 and M-54 linkert carburetors.Sold as a pack of 5. Fits:W 1933-1952VL 1933-1937G 1933-1957U 1938-1948Additional Information OEM No.27251-24 UOM5 - PK ManufacturerV-Twin OriginImported 2025 Catalog...

Linkert carburetor choke lever is zinc plated.Lever is for side valve models when using a 7" round air cleaner. Choke lever screw not included. Fits:W 1933-1952VL 1933-1936FL 1941-1947G 1953-1954EL 1937-1947U 1936-1948Additional Information OEM No...

Fixed Linkert carburetor main jet #19 is for M61, M74 and M74B linkerts. Fits:FL 1951-1965Additional Information OEM No.27318-51 UOM1 - EA ManufacturerV-Twin OriginImported TypeLinkert 2025 Catalog Pages707

Fixed Linkert carburetor jet #18.Fixe jet is for M36 and M61 Linkerts only. Fits:FL 1951-1965Additional Information OEM No.27318-50 UOM1 - EA ManufacturerV-Twin OriginImported TypeLinkert 2025 Catalog Pages707

Linkert carburetor #1 fixed jet.Fixed jet .052 hole is for M88 army Linkert only. Fits:FL 1941-1954 for 45 modelsW 1940-1950 for 45 modelsAdditional Information OEM No.27318-41 UOM1 - EA ManufacturerV-Twin OriginImported TypeLinkert 2025 Catalog...

Carburetor Oversize High Speed Needle Valve Fits:UL 1937-1948FL 1940-1950WL 1929-1952Additional Information UOM1 - EA ManufacturerV-Twin OriginUSA 2025 Catalog Pages708

Carburetor high speed needle valve. Fits:UL 1937-1948FL 1940-1950WL 1929-1952Additional Information OEM No.27297-27 UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages708 Tech NoteSuggested to use with #35-9052 Carburetor Needle Valve...

Linkert carburetor throttle lever is zicad plated.Stainless steel screws included. Lever features one hole for cable block location. ...

Petcock shut-off rod seal kit. Fits:FL 1941-1965Additional Information UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages1195

Petcock shut off rod seat with chrome finish. Fits:FL 1950-1965Additional Information OEM No.62075-50 UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages1195

Carburetor linkert detent ball Fits:FL 1941-1965Additional Information OEM No.27406-26 UOM10 - PK ManufacturerV-Twin OriginImported 2025 Catalog Pages708

Linkert carburetor bowl drain screw. Fits:FL 1941-1965K 1952-1956XL 1957-1965G 1939-1965W 1939-1952EL 1939-1940Additional Information OEM No.27377-39 UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages708

Linkert carburetor idle body plug is 5/16-32 TPI. Fits:FL 1941-1965Additional Information OEM No.27325-33 UOM5 - PK ManufacturerV-Twin OriginImported 2025 Catalog Pages708

Linkert carburetor float pivot pin with caps. No need for shims or filling when using these.Carburetor float pivot pin is manufactured to meet OEM specifications for long lasting durability and performance. Fits:FL 1941-1965Additional Information OEM No...

Linkert carburetor throttle disc is for 1-1/4" bore carburetors. Stamped #13 with correct bevel standard size. Fits:UL 1937-1948WL 1929-1952G 1936-1954Additional Information OEM No.27280-24 UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog...

Linkert carburetor throttle shaft is for 1-1/4" bore carburetors. Fits:UL 1937-1948WL 1944-1951G 1936-1954GD 1936-1941Additional Information OEM No.27275-24 UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages708

Linkert carburetor float pivot nut and bolt features a brass consturction. Fits:FL 1941-1965Additional Information UOM5 - PK ManufacturerV-Twin OriginImported 2025 Catalog Pages708

Linkert carburetor low speed needle valve is type (2) head and is 4" overall in length with 1/4"-40 threads.Smaller head style reassemble correctly for assembly, see repair or parts manual. The needle length measures 3" from the base of the threads...

Replica linkert carburetor needle has a 90  top bend. Fits:FL 1950-1965Additional Information OEM No.27300-50 UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages708 Tech NoteSuggested to use with #35-9052 Carburetor Needle Valve Lever

Linkert carburetor valve lever shoulder screw Fits:FL 1941-1965Additional Information OEM No.27397-27 UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages708

Linkert carburetor needle valve lever kit includes, brass arm with detent ball installed, collar, spring and shoulder screw with 1/4-40 thread.Lever has one fixed ball to contact choke cam, and one spring loaded ball for adjuster screw. Kit includes cast...

Linkert carburetor spring collar is for low speed mixture shaft and is the thicker type. Fits:FL 1941-1965Additional Information OEM No.27345-41 UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages708

Linkert float lever screw kit with pin is machined of brass and is for all linkert brass carburetors. Fits:FL 1941-1965EL 1936-1952Additional Information OEM No.27384-16 UOM1 - KIT ManufacturerV-Twin OriginImported 2025 Catalog Pages708

Cadmium plated linkert carburetor needle valve lever kit includes arm with detent ball installed, collar, spring and shoulder screw.Lever has one fixed ball to contact choke cam, and one spring loaded ball for adjuster screw. Kit includes lever, washer,...