Touring Electra Glide Classic FLHTC

Wheel and caliper kit includes a chrome wheel assembly, chrome caliper, chrome 51 tooth sprocket, rear drilled disc, bolts, chrome caliper bracket, support spring, and chrome stay bar with bolts...

16" x 3.0" front or rear wheel assembly includes chrome profile smooth rim, chrome hub with 3/4" bearings and internals installed, chrome spokes.Wheel has a 3/8" disc hole and 7/16" sprocket mount...

Chrome 16" x 3.0" wheel assembly is laced and trued with bearings installed.Includes a drilled 11-1/2" steel brake disc and a chrome 51 tooth sprocket. Chrome bolts are supplied for each side. ...

Chrome 16" x 3.0" wheel assembly is laced and trued with bearings installed.Includes drilled 10" steel brake disc and a chrome 51 tooth sprocket. Chrome bolts are supplied for each side. ...

XR Front or rear wheel includes a chrome hub with internals installed stainless steel spokes and nipples, a chrome 19" x 3.0" steel rim and a rim strip. For use with a dirt tire.Features a 8.5mm...

V-Twin - 52-0300 - 16 inch x 3 inch Wheel Rim and Spoke Kit Chrome SteelDescriptionRim and spoke set include 16" x 3" front rim with 40 chrome spokes with 40 spoke nipples.For use with a steel hub...

Replica 16" X 3.00" wheel assembly features drop center chrome rim, 40 stainless steel spokes, chrome hub with internals, for front or rear applications.The hole for the valve stem that is located on...

Replacement tank mounts can be used on Fat Bob tanks and also on custom frames where the mounts do not exist. Fits:FL 1955-1984Additional Information UOM

V-Twin - 51-1955 - Replica inchHM inch Straight Leg Rigid FrameDescriptionReplica "HM" straight leg rigid frame is an authentic reproduction of the 1954-1957 straight leg frame with stock 30  neck...

Engine mount shim is used to raise motor for front or rear clearance, when necessary.Sold in a pack of 5. Fits:FL 1941-1999EL 1936-1952Additional Information

V-Twin - 51-1322 - Lowered Rear Axle Plate Set RawDescriptionLowered rear axle plates are threaded 3/8"-18 for fender brace sissy bar mounting. Adjusters threaded 3/8"-24 use screws for adjusters, to...

Replica swingarm frame is our authentic reproduction of FLH style to accept a Panhead or Shovelhead engine, 4-speed transmission, seat post, and accepts a round or square swingarm. All components are...

Replica swingarm frame is an authentic reproduction of FLH style for 1965-1984.Frame accepts Panhead or Shovelhead engine, 4-speed transmission, 12v battery and round swingarm for drum brake...

This replica authentic style frame neck web repair section must be welded in after cutting stock or custom frame. It features the right side lock housing.Order new lock assembly, separately. Fits:FL...

Engine bar set features left and right sides.Two piece set. **WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while...

Engine bar features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide)...

Rigid hardtail frame raw steel rear section is 1957 style replica construction with components featuring the factory details of the period.The rear transmission mounts are 2" from the bottom cross...

Raw finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications. Swingarm is for use...

Replica rear hardtail frame section is duplicated from an original rigid frame of 1957. Left axle plates are forged steel as OE. Weld-on type. The axle slots are 7/8" on both sides.Full replica...

Chrome finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications.Lowers bike 1/2"...

Lower frame gas tank mount set is without cross bracket. It includes the right and left tabs. Tabs are constructed of st eel and have a raw finish.May require finishing prior top installation and...

This 5th Mount transmission frame repair tab is weld on style for stock frames. The tab is constructed of steel and has a raw finish.May require finishing prior to installing. Fits:FX 1971-1984FL...

Rear pipe frame tab. Fits: FL 1958-1984 Additional Information UOM 1 - EA Manufacturer V-Twin

Brake line tee tab. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA Manufacturer

Upper shock frame mounts are weld on style for stock frames.Sold as a set of two. Fits:FL 1965-1984FX 1971-1984Additional Information UOM1

Casting top seat mount is for frame seat post, frame back bone and frame upper seat rail yoke. Fits:FL 1958-1984Additional Information UOM1 - EA

This weld on style coil mount frame block set repairs stock frames and has a 3/8"-24 UNF thread. Fits:FL 1956-1983FX 1971-1983Additional Information UOM<

Rigid frame front oil tank mount casting to be welded on.Thread is 5/16 x 24 and the lip from the bottom to the top measures 1-1/4". For use with 1-1/2" bar. Fits:FL 1941-1984FX 1972-1984EL...

Rear frame engine mount and front transmission mount. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA

Rear tank frame mount tabs. Fits:FL 1941-1984EL 1936-1947U 1937-1948Additional Information UOM1 - SET

Weld on frame footpeg mount without thread.Mount can be welded to 1958-1977 swingarm frames to utilize the stock FXE mount and raise the peg position. Sold as a pair. Fits:FX 1971-1978FL...

Replica rear hardtail frame section is duplicated from an original rigid frame. Weld-on type and does not have seat post bushing.The rear transmission mounts are 1-1/2" tall. This hardtail includes...

Beaded windshield is a fixed mount type which comes completely assembled.Includes beaded windshield top and an adjustable lower windshield to fit FL aluminum headlamp cowl assembly. The center bolt...

Top beaded windshield measure 18" and is for use on fiberglass fairings only.Fits 1969-1984 FLH 4 speed and 1980-1985 FLT 5 speed models with Batwing fairings. Fits:FLT 1980-1985FLH...

Top beaded windshield is short style. Fits:FLH 1949-1984Additional Information OEM No.58020-49A UOM1

Frame saver mounting kit for gas tanks must be welded to Big Twin stock or custom frames. Casting features provision for damper pin, as required on 1949-1984 Big Twins.*Note: Includes speedometer...

Replica wishbone frame is an authentic reproduction of a 1948 Big Twin rigid frame with seat post, axle, and transmission plate already installed. The legs are smooth and do not have horn mount...

Solid steel frame dowel set is for the installation of hardtails.Outer diameter on small end is .7225 and large end is .8375. *NOTE: Must be welded in place. Fits:FL 1958-1984Additional Information

FL fender strut set features a chrome finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. The distance from the...

FL fender strut set features a black finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. *NOTE: Requires 7-1/4"...