Touring Electra Glide Highway King FLHFB

New Old Stock" Frame gusset plate is for the left side on swingarm frames.New Old Stock from the 1980's, part has rust and oxidation! Fits:FL 1958-1968FLH 1958-1968Additional Information

Weld on frame footpeg mount without thread.Mount can be welded to 1958-1977 swingarm frames to utilize the stock FXE mount and raise the peg position. Sold as a pair. Fits:FX 1971-1978FL...

Raw steel neck lock pin only. Fits:FL 1948-1968VL 1930-1936Additional Information UOM1 - EA Manufactu

Replica rear hardtail frame section is duplicated from an original rigid frame. Weld-on type and does not have seat post bushing.The rear transmission mounts are 1-1/2" tall. This hardtail includes...

Steering lock assembly kit includes complete key assembly, key lock, two keys, spring, pin, plunger, frame plug, and neck casting piece for lock. Must be welded in place.Steering lock assembly kit...

Beaded windshield is a fixed mount type which comes completely assembled.Includes beaded windshield top and an adjustable lower windshield to fit FL aluminum headlamp cowl assembly. The center bolt...

Top beaded windshield is short style. Fits:FLH 1949-1984Additional Information OEM No.58020-49A UOM1

Frame saver mounting kit for gas tanks must be welded to Big Twin stock or custom frames. Casting features provision for damper pin, as required on 1949-1984 Big Twins.*Note: Includes speedometer...

Replica wishbone frame is an authentic reproduction of a 1948 Big Twin rigid frame with seat post, axle, and transmission plate already installed. The legs are smooth and do not have horn mount...

Solid steel frame dowel set is for the installation of hardtails.Outer diameter on small end is .7225 and large end is .8375. *NOTE: Must be welded in place. Fits:FL 1958-1984Additional Information

V-Twin - 50-2064 - Lindby Custom Front Engine BarDescriptionFront engine bar feature 1-1/8" tubing with built in O-rings on the footpeg area.Front engine bar is constructed of a high strength steel...

Raw alignment clips are for hinged rear fenders, to be spot welded on the front portion of the fender.Sold as a pair. *NOTE: Used to align and hold the rear tail flap edges in place. Fits:FLH...

Swingarm rear fender hinge features a raw finish. Hinge includes both halves with pin but without wire loom tail.Hinge halves are produced with correct pin and hinge offset for installing on original...

Raw steel wire loom fender strip for inside of the left FL rear hinged fender, radiused to fit the fender contour, and segmented to accept tail lamp wires.Must be spot welded to the left side or...

Wire loom spring clamp features a raw finish and is for use with the rear fender. To hold spring loom cover in place use #32-2036. Clamp is sold in a pack of 5.*NOTE: Must be spot welded on. Fits:FL...

FL fender strut set features a chrome finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. The distance from the...

FL fender strut set features a black finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. *NOTE: Requires 7-1/4"...

V-Twin - 50-1148 - Zinc Plated Fender BracketDescriptionZinc plated steel bracket used to adapt one piece FXDF front fenders to fit FLH forks on 1949-up 41mm models.Set of two. Bracket is formed from...

Front fender trim kit includes chrome front fender tip and front fender trim side rails for FL models. Fits:FL 1967-1972Additional Information UOM1 - SET

2022 New Production Replica rear fender is flip style with updated hinged tail.Fender will accept 1955-1972 type tail light. We suggest pre fitting the fender prior to painting. Before priming or...

Chrome rear fender strut set is of solid steel construction and is for use with Bobbed fender only. Fits:FX 1973-1984FL 1958-1984Additional Information U

Drag Specialties - DS240985 - Kick Pedal Bolt Kit - '31-'76 Harley-DavidsonFeaturesKit includes chrome-plated bolt, pedal bushing, spring washer and lock washerReplacement Part for OEM...

Drag Specialties - DS240210 - Kickstand Leg StopFeaturesReplacement component for chrome kickstandsReplacement Part for OEM Number(s):5001574,5002874Specs

Drag Specialties - DS196010 - Kickstarter ShaftFeaturesHigh-quality steel replacement shaftMachined for an exact fitReplacement Part for OEM Number(s):3309654BSpecs

Drag Specialties - 21130216 - Battery Kit - CHD4-12FeaturesMSDS Migration DataDrag Specialties Conventional batteries are built to the same exacting specifications and quality-control standards as...

Drag Specialties - 21100224 - Starter - High-Torque - ChromeFeaturesFeatures 15% more power and torque than OEM unitsManufactured using heavy-duty armature commutators, large drive-end bearings and...

Drag Specialties - 21100223 - Starter - High-Torque - BlackFeaturesFeatures 15% more power and torque than OEM unitsManufactured using heavy-duty armature commutators, large drive-end bearings and...

S&S Cycle - 93-4070 - Pushrod Cover Keeper Set - Chrome - 2.400"FeaturesFor use in custom applications where stock keepers won't fitChromed steel finishSold in kits of four assemblies; enough for one...

S&S Cycle - 93-4115 - Pushrod Cover Keeper Set - Chrome - 2.800"FeaturesFor use in custom applications where stock keepers won't fitChromed steel finishSold in kits of four assemblies; enough for one...

S&S Cycle - 93-4106 - Pushrod Cover Keeper Set - Chrome - 3.330"FeaturesFor use in custom applications where stock keepers won't fitChromed steel finishSold in kits of four assemblies; enough for one...

S&S Cycle - 34-4040 - Race Bearing Set - Big TwinFeaturesUsed to rebuild S&S and stock connecting rodsIncludes hardened steel rod bearing races and bronze wrist pin bushingsRequires finish sizing...

Lang Tools - 9794 - Wrench - Crankshaft - 10 Spline - RatchetingFeaturesUsed for rotation of the crankshaft/check engine timing and parts clearance on Sportster® motorcyclesEZ Grip screwdriver-style...

Kb Performance - RRN-81-4PK - Wrist Pin Lock RingFeaturesReplacement piston lock rings for KB Performance Piston KitSpecs

Eastern Motorcycle Parts - A-33438-50 - Starter Ratchet BushingFeaturesMade in the U.S.A.Replacement Part for OEM Number(s): 3343850Specs

Replica Wagner style rear master cylinder for drum brake. The cast iron body is painted silver with a natural aluminum top. Master cylinder is 3/4 inch bore. NOTE: Wagner Lockheed replacement not...

V-Twin - SMC Electric Start Oil Tank fits '58-'64 FL, '71-'85 FX Models Swingarm York oil tank features a chrome finish. Oil tank is for use on 4-speed models with a stock swingarm frame. tncludes...

V-Twin - Nickel Plated Tappet Block Screw Kit fits '48-'84 FL Model Tappet base bolt set of eight with 1/4" x 20UNC thread, is nickel plated, and has a hex shaped head. Screw does not have taper and...

3 speed and reverse chrome left side tank hand shifter gate, has a 32N1R front to rear shift pattern. The distance center to center of the screw holes is 3.5". Note: Use 1/4"-28 x 1/2" hex head...

Zinc plated shift gate hex screws is 1/4"-28 x 1/2", National Coarse. Sold in a pack of 5. Fitment: G 1947-1973 FL 1947-1965

Swingarm frame oil tank rear mount bracket with spacers features bright zinc plating. Fitment: FL 1958-1984