Electra Glide FLH

Zinc slot type transmission top cover screw kit contains stock fasteners and special vent screw. Fits:UL 1937-1948FL 1941-1978FX 1971-1978EL 1936-1940Additional Information

Motor case drain/oil pump body plug has a zinc finish. Fits: UL 1937-1948 Case F 1911-1920 Case J 1921-1929 Case FL 1968-1984 Oil pump FX 1971-1984 Oil pump EL 1936-1940 Case VL 1930-1936...

Chrome hex stock type kit includes nuts and washers for the transmission side cover and clutch arm. Fits:UL 1937-1948FX 1971-1984EL 1936-1940FL 1941-1984Additional Information

Zinc plated cylinder base nut stock set includes 8 nuts with washers. Fits:FX 1971-1977EL 1936-1940FL 1941-1977Additional Information UOM

Zinc plated cylinder base nut stock set includes 8 nuts with washers. Fits:FX 1971-1977EL 1936-1940FL 1941-1977Additional Information UOM

Stock headbolt kit with washers features a zinc finish. Fits:FX 1971-1984FL 1948-1984Additional Information UOM1 - KIT

Rear chain adjuster features a parkerized finish.Chain adjuster features a 3/8 - 24 thread with a hex head. Fits:FL 1941-1972UL 1937-1948EL 1936-1940Additional Information

V-Twin - 7508-20T - Chrome Pushrod Cover and Clip KitDescriptionChrome pushrod cover and clip kit includes 4 clips and cups, seals, springs and cork washers. Fits:FXST 1984-UPFL 1940-1947FXD...

V-Twin - 7506-4 - Solid Shovelhead Pushrod SetDescriptionSolid shovelhead pushrod set is alloy construction with hardened steel ends tips.For use with solid tappets with build in adjusters and lock...

Retainer and seal kit for the sprocket shaft Fits:FL 1955-1968Additional Information UOM1 - EA Manufacturer

Frame and rork kit includes straight leg rigid frame, a 1" overstock inline black spring fork and an inline Spring Fork handlebar. The 1" compliments the 30  frame. Assembly accepts Shovelhead or...

Shock stud kit includes all pieces for upper and lower positions. Kit includes washers, nuts and lock washers.Longer studs measure 1/2" and the shorter studs measure 5/8". Fits:FL 1967-1972Additional...

Chrome lower rear shock stud kit includes four cup washers and two studs. Fits:FL 1967-1972FX 1971-1972Additional Information OEM No.54517-67

Upper rear shock stud kit includes one stud, one 3/8 cup washer, one 5/8" cup washer, one shock stud spacer, two rubber shock bushings, one 5/8-18 mounting nut, and one 3/8" chrome nugget. Fits:FL...

Zinc stock stud spacers replace 5960W on 1965-1985 FLH when rear frame bars are not used. Fits:FL 1965-1984Additional Information OEM No.5960W

Zinc Nyloc shock stud nut is 5/8-18 UNC thread. Fits:XL 1957-1974KH 1954-1956FX 1971-1984FL 1958-1984Additional Information OEM No.

V-Twin - 54-0421 - Chrome Shock Stud Washers 1/2 inch HoleDescriptionChrome 1/2" hole x 1" flat shock stud washers Fits:FLT 1997-UPFXR 1982-1994FL 1965-1984FX 1971-1984XL 1975-UPFXD...

Chrome 1/2" hole cup shock stud washers Fits:FL 1965-1984FX 1971-1984XLH 1972-1974Additional Information OEM No.54545-65

Chrome 3/8" hole cup shock stud washers Fits:FX 1971-1984XLH 1972-1974FL 1965-1972Additional Information OEM No.54543-65

Chrome 5/8" hole cup shock stud washers Fits:XLH 1965-1974FX 1971-1972FL 1965-1972Additional Information UOM10 - PK

Lower rear shock stud kit includes four cup washers and two studs. Fits:FL 1967-1972FX 1971-1972Additional Information OEM No.54517-67

Upper rear shock stud kit includes four cup washers and two studs. Fits:FL 1967-1972Additional Information OEM No.54515-67

H-12 battery cast is plastic as original battery, with a removable top. Kit features a mock plastic top that will house most smaller batteries and mounts like an original battery.Mock battery box is...

H-12 battery top cover with terminals. Fits:FL 1965-1984XL 1967-1978Additional Information UOM1 - EA

Battery top set is a six piece set. Fits:FL 1965-1984Additional Information UOM6 - SET ManufacturerV-

V-Twin - 53-0501 - 12 Volt AGM H-12 Sealed Battery BlackDescriptionAbsorbed Glass Mat technology proposes the best balance between cold cranking amps and amp hour capacity.AGM battery is fully sealed...

16" x 3.00" front or rear KH style wheel assembly includes a black hub, zicad plated spokes and a black rim.*NOTE: Zicad is a dull shade of zinc similar to cadmium. *NOTE: All spokes...

Chrome 18" X 2.15" steel wheel rim features a full roll edge with weld in side.Rim features a rolled inner seam, features a bead construction with a width of 2.20". Valve stem center hole measures 8...

16" X 3.00" wheel assembly includes chrome hub, rim and stainless steel spokes.This wheel assembly also includes lock screw, seal spacer, tube spacer and one bearing. The hub must be supported by a...

Replica black powder coated front or rear 18" X 2.15" steel wheel rim. This is a WM type rim with welded beaded construction.Features conventional bead construction with a bead width of 2.20". ...

Includes a black hub, chrome rim and zicad plated spokes.Wheel assembly is laced, trued. The bearing kit inlcuded, includes the bearings, inner tube and outer nut with seal and spacer. *NOTE: The...

16" X 3.0" front or rear wheel assembly includes black hub, chrome rim and 40 zicad plated spokes.*NOTE: Zicad is a dull shade of zinc similar to cadmium. This wheel assembly also...

V-Twin - 52-0300 - 16 inch x 3 inch Wheel Rim and Spoke Kit Chrome SteelDescriptionRim and spoke set include 16" x 3" front rim with 40 chrome spokes with 40 spoke nipples.For use with a steel hub...

Replacement tank mounts can be used on Fat Bob tanks and also on custom frames where the mounts do not exist. Fits:FL 1955-1984Additional Information UOM

V-Twin - 51-1955 - Replica inchHM inch Straight Leg Rigid FrameDescriptionReplica "HM" straight leg rigid frame is an authentic reproduction of the 1954-1957 straight leg frame with stock 30  neck...

Weld-on brake tab features a raw finish. Mounts stock or replica frames to the rear drum brake backing plate. Fits:FL 1958-1972Additional Information UOM

Engine mount shim is used to raise motor for front or rear clearance, when necessary.Sold in a pack of 5. Fits:FL 1941-1999EL 1936-1952Additional Information

Engine bar features 1" tubing and a black finish.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very slow...

Replica swingarm frame is our authentic reproduction of FLH style to accept a Panhead or Shovelhead engine, 4-speed transmission, seat post, and accepts a round or square swingarm. All components are...

Replica swingarm frame is an authentic reproduction of FLH style for 1965-1984.Frame accepts Panhead or Shovelhead engine, 4-speed transmission, 12v battery and round swingarm for drum brake...