1968

This 5th Mount transmission frame repair tab is weld on style for stock frames. The tab is constructed of steel and has a raw finish.May require finishing prior to installing. Fits:FX 1971-1984FL...

Rear pipe frame tab. Fits: FL 1958-1984 Additional Information UOM 1 - EA Manufacturer V-Twin

Brake line tee tab. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA Manufacturer

Cable mount frame tab is for under tank. Fits:FL 1955-1972Additional Information UOM1 - EA Manufacturer

Upper shock frame mounts are weld on style for stock frames.Sold as a set of two. Fits:FL 1965-1984FX 1971-1984Additional Information UOM1

Casting top seat mount is for frame seat post, frame back bone and frame upper seat rail yoke. Fits:FL 1958-1984Additional Information UOM1 - EA

Frame mount tab set for solo seats have weld on mount tabs. Use with T bar and pivot bolt to mount K and CH solos. Fits:XL 1957-1979Additional Information UOM

This weld on style coil mount frame block set repairs stock frames and has a 3/8"-24 UNF thread. Fits:FL 1956-1983FX 1971-1983Additional Information UOM<

Frame top engine mount is two halves with seat tee and rear tank mounts incorporated into the top mount. Weld in place for accurate restoration.*NOTE: Threaded for seat "T" bolt. Fits:FL...

Rigid frame front oil tank mount casting to be welded on.Thread is 5/16 x 24 and the lip from the bottom to the top measures 1-1/4". For use with 1-1/2" bar. Fits:FL 1941-1984FX 1972-1984EL...

Rear frame engine mount and front transmission mount. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA

Neck frame forging has a 30  rake with key hole. Machined to accept neck lock tumbler.Forged neck is accomplished in 4 stages: First the steel is fired as red hot ingot, next huge hammers compact and...

Rear tank frame mount tabs. Fits:FL 1941-1984EL 1936-1947U 1937-1948Additional Information UOM1 - SET

New Old Stock" Frame gusset plate is for the left side on swingarm frames.New Old Stock from the 1980's, part has rust and oxidation! Fits:FL 1958-1968FLH 1958-1968Additional Information

Weld on frame footpeg mount without thread.Mount can be welded to 1958-1977 swingarm frames to utilize the stock FXE mount and raise the peg position. Sold as a pair. Fits:FX 1971-1978FL...

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

Raw steel neck lock pin only. Fits:FL 1948-1968VL 1930-1936Additional Information UOM1 - EA Manufactu

Replica rear hardtail frame section is duplicated from an original rigid frame. Weld-on type and does not have seat post bushing.The rear transmission mounts are 1-1/2" tall. This hardtail includes...

XL raw brake shaft tube for mechanical brakes. Kit includes machined 7.25" tube with brass bushing and shifter cross bushing set installed. Must be welded in place to frame.*NOTE: Locate tube using...

Steering lock assembly kit includes complete key assembly, key lock, two keys, spring, pin, plunger, frame plug, and neck casting piece for lock. Must be welded in place.Steering lock assembly kit...

Beaded windshield is a fixed mount type which comes completely assembled.Includes beaded windshield top and an adjustable lower windshield to fit FL aluminum headlamp cowl assembly. The center bolt...

Top beaded windshield is short style. Fits:FLH 1949-1984Additional Information OEM No.58020-49A UOM1

Frame saver mounting kit for gas tanks must be welded to Big Twin stock or custom frames. Casting features provision for damper pin, as required on 1949-1984 Big Twins.*Note: Includes speedometer...

Replica wishbone frame is an authentic reproduction of a 1948 Big Twin rigid frame with seat post, axle, and transmission plate already installed. The legs are smooth and do not have horn mount...

Solid steel frame dowel set is for the installation of hardtails.Outer diameter on small end is .7225 and large end is .8375. *NOTE: Must be welded in place. Fits:FL 1958-1984Additional Information

V-Twin - 50-2064 - Lindby Custom Front Engine BarDescriptionFront engine bar feature 1-1/8" tubing with built in O-rings on the footpeg area.Front engine bar is constructed of a high strength steel...

Raw alignment clips are for hinged rear fenders, to be spot welded on the front portion of the fender.Sold as a pair. *NOTE: Used to align and hold the rear tail flap edges in place. Fits:FLH...

Swingarm rear fender hinge features a raw finish. Hinge includes both halves with pin but without wire loom tail.Hinge halves are produced with correct pin and hinge offset for installing on original...

Raw steel wire loom fender strip for inside of the left FL rear hinged fender, radiused to fit the fender contour, and segmented to accept tail lamp wires.Must be spot welded to the left side or...

Wire loom spring clamp features a raw finish and is for use with the rear fender. To hold spring loom cover in place use #32-2036. Clamp is sold in a pack of 5.*NOTE: Must be spot welded on. Fits:FL...

FL fender strut set features a chrome finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. The distance from the...

FL fender strut set features a black finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. *NOTE: Requires 7-1/4"...

V-Twin - 50-1148 - Zinc Plated Fender BracketDescriptionZinc plated steel bracket used to adapt one piece FXDF front fenders to fit FLH forks on 1949-up 41mm models.Set of two. Bracket is formed from...

Front fender trim kit includes chrome front fender tip and front fender trim side rails for FL models. Fits:FL 1967-1972Additional Information UOM1 - SET

Bobbed rear fender kit includes a steel fender, cateye tail lamp, chrome tail lamp bracket, and chrome struts.We suggest pre fitting fender prior to painting. Order sissy bar components separately. ...

2022 New Production Replica rear fender is flip style with updated hinged tail.Fender will accept 1955-1972 type tail light. We suggest pre fitting the fender prior to painting. Before priming or...

Chrome rear fender strut set is of solid steel construction and is for use with Bobbed fender only. Fits:FX 1973-1984FL 1958-1984Additional Information U

V-Twin - 50-0625 - XL Rigid Tool Box KitDescriptionLeft side tool box kit is the weld on type for rigid frames on Sportster builds.*NOTE: Weld bracket to lower rigid frame hardtail tube position or...

Magneto advance plate screw set includes four allen flathead screws and 2 hex screws with lock nuts.Kit includes 4 tapered screws for mounting base to magneto head. Fits 1965-70 XL with Magneto cable...

Drag Specialties - DS325386 - Rear Brake Shoes - '63-'72 Big TwinFeaturesHigh-quality brake shoesReplacement Part for OEM Number(s):4180163Specs