1976

Chrome finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications.Lowers bike 1/2"...

This raw steel full rear section hardtail for Sportsters includes the rear motor mount and 4 bolt plate mount with upper and lower tube set. Frame is used to replace the stock rear motor mount and...

Lower frame gas tank mount set is without cross bracket. It includes the right and left tabs. Tabs are constructed of st eel and have a raw finish.May require finishing prior top installation and...

This 5th Mount transmission frame repair tab is weld on style for stock frames. The tab is constructed of steel and has a raw finish.May require finishing prior to installing. Fits:FX 1971-1984FL...

Rear pipe frame tab. Fits: FL 1958-1984 Additional Information UOM 1 - EA Manufacturer V-Twin

Brake line tee tab. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA Manufacturer

Upper shock frame mounts are weld on style for stock frames.Sold as a set of two. Fits:FL 1965-1984FX 1971-1984Additional Information UOM1

Casting top seat mount is for frame seat post, frame back bone and frame upper seat rail yoke. Fits:FL 1958-1984Additional Information UOM1 - EA

Frame mount tab set for solo seats have weld on mount tabs. Use with T bar and pivot bolt to mount K and CH solos. Fits:XL 1957-1979Additional Information UOM

This weld on style coil mount frame block set repairs stock frames and has a 3/8"-24 UNF thread. Fits:FL 1956-1983FX 1971-1983Additional Information UOM<

Rigid frame front oil tank mount casting to be welded on.Thread is 5/16 x 24 and the lip from the bottom to the top measures 1-1/4". For use with 1-1/2" bar. Fits:FL 1941-1984FX 1972-1984EL...

Rear frame engine mount and front transmission mount. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA

Neck frame casting fits XL models to be welded in place on 30  stock or custom frames. Has unmachined padlock boss. Accepts neck cup kit.Neck frame accepts stock bearing cups and trees. Fits:XL...

Rear tank frame mount tabs. Fits:FL 1941-1984EL 1936-1947U 1937-1948Additional Information UOM1 - SET

Weld on frame footpeg mount without thread.Mount can be welded to 1958-1977 swingarm frames to utilize the stock FXE mount and raise the peg position. Sold as a pair. Fits:FX 1971-1978FL...

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

Replica rear hardtail frame section is duplicated from an original rigid frame. Weld-on type and does not have seat post bushing.The rear transmission mounts are 1-1/2" tall. This hardtail includes...

XL raw brake shaft tube for mechanical brakes. Kit includes machined 7.25" tube with brass bushing and shifter cross bushing set installed. Must be welded in place to frame.*NOTE: Locate tube using...

Beaded windshield is a fixed mount type which comes completely assembled.Includes beaded windshield top and an adjustable lower windshield to fit FL aluminum headlamp cowl assembly. The center bolt...

Top beaded windshield measure 18" and is for use on fiberglass fairings only.Fits 1969-1984 FLH 4 speed and 1980-1985 FLT 5 speed models with Batwing fairings. Fits:FLT 1980-1985FLH...

Top beaded windshield is short style. Fits:FLH 1949-1984Additional Information OEM No.58020-49A UOM1

Frame saver mounting kit for gas tanks must be welded to Big Twin stock or custom frames. Casting features provision for damper pin, as required on 1949-1984 Big Twins.*Note: Includes speedometer...

Replica wishbone frame is an authentic reproduction of a 1948 Big Twin rigid frame with seat post, axle, and transmission plate already installed. The legs are smooth and do not have horn mount...

Solid steel frame dowel set is for the installation of hardtails.Outer diameter on small end is .7225 and large end is .8375. *NOTE: Must be welded in place. Fits:FL 1958-1984Additional Information

Raw alignment clips are for hinged rear fenders, to be spot welded on the front portion of the fender.Sold as a pair. *NOTE: Used to align and hold the rear tail flap edges in place. Fits:FLH...

Swingarm rear fender hinge features a raw finish. Hinge includes both halves with pin but without wire loom tail.Hinge halves are produced with correct pin and hinge offset for installing on original...

Raw steel wire loom fender strip for inside of the left FL rear hinged fender, radiused to fit the fender contour, and segmented to accept tail lamp wires.Must be spot welded to the left side or...

Wire loom spring clamp features a raw finish and is for use with the rear fender. To hold spring loom cover in place use #32-2036. Clamp is sold in a pack of 5.*NOTE: Must be spot welded on. Fits:FL...

FL fender strut set features a chrome finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. The distance from the...

FL fender strut set features a black finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. *NOTE: Requires 7-1/4"...

V-Twin - 50-1148 - Zinc Plated Fender BracketDescriptionZinc plated steel bracket used to adapt one piece FXDF front fenders to fit FLH forks on 1949-up 41mm models.Set of two. Bracket is formed from...

Bobbed rear fender kit includes a steel fender, cateye tail lamp, chrome tail lamp bracket, and chrome struts.We suggest pre fitting fender prior to painting. Order sissy bar components separately. ...

Chrome rear fender strut set is of solid steel construction and is for use with Bobbed fender only. Fits:FX 1973-1984FL 1958-1984Additional Information U

V-Twin - 50-0625 - XL Rigid Tool Box KitDescriptionLeft side tool box kit is the weld on type for rigid frames on Sportster builds.*NOTE: Weld bracket to lower rigid frame hardtail tube position or...

Drag Specialties - DS317463 - Battery Strap - '70-'78 FX/XLCHFeaturesHigh-quality replacement battery strapsMeets or exceed OEM specificationsSpecs

Drag Specialties - DS240360 - Fork Boots - 41 mm - FL/FLH '48-'77 (Early)FeaturesMolded rubber constructionReplacement Part for OEM Number(s):4598373Specs

Drag Specialties - DS240215 - Long Clutch Lever Rod End - '36-'78 FLFeaturesRod end for long "mousetrap" clutch lever rodReplacement Part for OEM Number(s):3691636Specs

Drag Specialties - 24020162 - Cover - Bolt - Deep - Hex - BlackFeaturesDesigned to fit stock-style, 3/4" front axles with 7/8" head and 1/2" hex nut (3/4" wrench size)Attach with silicone (silicone...

Drag Specialties - 24010850 - Board Mount Screws with Nuts - FrontFeaturesHas all required hardware for mounting driver floorboards to the mount bracketsIncludes four shouldered bolts and four...

Drag Specialties - 21130793 - AGM Battery - YTX20H FTFeaturesPremium-quality, maintenance-free batterySpecial absorbed-glass mat battery eliminates water lossBattery seals to prevent water lossHolds...