1987

19" x 2.50" Replica single disc front wheel features a chrome hub with all internal bearings installed, 40 polished stainless steel spokes and a chrome drop center rim.**NOTE: All spokes on wheel...

21" x 2.15" Replica single disc front wheel features a chrome hub with all internal bearings installed, chrome spokes, and a chrome rimAll spokes on wheel need to be inspected and re-torqued after...

19" x 2.50" Replica single disc front wheel features a chrome hub with all internal bearings installed, 40 chrome spokes, and a drop center chrome rimFeatures a 3/4" bearing. **NOTE: All spokes on...

Wheel features a 16" X 3.00" chrome rim, chrome hub with internals, and 40 chrome spokes.The flange of the hub measure 7" between each other. *NOTE: 32mm on the pulley side, valve stem side. 27mm...

Wheel features a Replica 16" x 3.00 chrome rim, a chrome hub with 3/4" bearings, and 40 chrome spokes.Single disc wheel is assembled and ready to directly bolt on to 41mm forks. This wheel has a side...

21" x 2.15" Replica single or dual disc front wheel features chrome hub with all internal bearings installed, 40 chrome spokes, and a chrome rim.**NOTE: All spokes on wheel need to be inspected and...

19" x 2.50" Replica single or dual disc front wheel features a chrome hub with bearings installed, chrome spokes, and a chrome drop center rim.**NOTE: All spokes on wheel need to be inspected and...

Features a Replica 21" x 2.15" chrome rim, a chrome hub with 3/4" bearings, and 40 chrome spokes.Rim has a rolled edge design for added strength. Single disc wheel is assembled and ready to directly...

Front 16" x 3.5" Duro 26 Fat Spoke wheel features a matte black finish and 25mm bearings.Wheel will accept dual 11" rotors. Wheel hub includes bearings installed. Wheel can be used with 11" rotors...

16" x 3.5" Duro 36 Fat Spoke unit wheel features a matte black hub. Wheel is one piece with aluminum casting. Includes 2 spacers 18.7mm thick for disc and pulley flange. With 3/4" bearings.Wheel hub...

Front 16" x 3.5" Duro 36 Fat Spoke wheel features a matte black finish and 3/4" bearings.Wheel will accept dual 11" rotors. Wheel hub includes bearings installed. Wheel can be used with 11" rotors...

Front 21" x 3.15" Duro 36 Fat Spoke cast type wheel is dual disc, and features a matte black finish with 25mm bearings.Wheel bearing adapter sleeve sets, available separately. ...

200 XL rigid frame features a 40  rake with a 3" stretch. Frame can be set up for 1957-1985 type Ironhead motors.Frame will accept 1" neck cups, Wide Glide fork assembly, stock length kickstand and...

V-Twin - 51-2076 - Chrome Front Engine BarDescriptionCustom engine bar feature 1-1/8" tubing for front engine bar with built in O-ring footpeg area features a chrome finish.Bar does not include...

V-Twin - 51-2052 - Black Front Engine BarDescriptionCustom engine bar feature 1-1/8" tubing for front engine bar with built in O-ring footpeg area features a black finish.WARNING: This engine/frame...

Engine mount shim is used to raise motor for front or rear clearance, when necessary.Sold in a pack of 5. Fits:FL 1941-1999EL 1936-1952Additional Information

V-Twin - 51-1322 - Lowered Rear Axle Plate Set RawDescriptionLowered rear axle plates are threaded 3/8"-18 for fender brace sissy bar mounting. Adjusters threaded 3/8"-24 use screws for adjusters, to...

Engine bar features integrated rubber pads for foot rests featuring a black finish.Does not include hardware. WARNING: This engine/frame bar may provide...

Engine bar features integrated rubber pads for foot rests featuring a chrome finish.Does not include hardware. WARNING: This engine/frame bar may...

Chrome left and right pivot mount end caps with footpeg mount holes.The OEM number for the right end cap is 50589-93, and the OEM number for the left end cap is 50588-93. Fits:FLT 1982-1984FLT...

Engine bar features 1-1/4" tubing.Includes bolts. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low...

Engine bar features 1-1/4" tubing.This engine bar is not for use with extended forward controls. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection...

Engine bar features 1-1/4" tubing and foot rests with rubber pads. Hardware is not included. This will not work with forward controls.**WARNING: This engine/frame bar may provide limited leg and...

Engine bar features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide)...

Passenger footboard set with swingarm mount kit includes streamline style mini footboards.A Wyatt Gatling patch is included in the kit. Installation will require re-installation of the original...

Chrome swingarm mount kit includes right & left side chrome pivot caps, passenger footboard mounts and passenger footboard with rubber pads.Installation will require re-installation of the original...

Raw steel hardtail rear frame section has replica forged axle plates for the exact look of the 1950's rigid frames. Accepts FXST oil tank, transmission mount plate and electric start.Hardtail for...

Left side caliper frame mount bracket for right side drive motorcycles must be welded on. Bracket is for rigid frames when mounting brake units. Fits:FLST 1987-1999FXST 1987-1999Additional Information

D+D XL raw rigid frame features a 1-1/4" thick wall, DOM steel tubing with 1-1/2" backbones, 30  rake and 0  stretch. This rigid frame is a basic starter frame.Frame will require custom 3/4" rear...

Big Twin neck forgings machined to accept stock diameter tubing with 30  rake.Includes key lock tab and right hand number boss forged in neck. *NOTE: This frame neck does not include Manufacturer's...

Mid control mount kit is used to mount to the two holes located in the lower frame brace. Kit features a black finish.Mount features holes on each side for the left and right foot brake peg mount...

XL control mount set features a black finish. Control mounts for right (2 bolt plate) and left (3 bolt plate) to accept Big Twin forward controls.Set is used to mount 1941-1999 Big Twin forward mount...

V-Twin - 51-0484 - XL Hardtail Axle Plate SetDescriptionRaw set of right and left axle plates for Sportster hardtails, features 7/8" slots on both sides. Fits:XL 1982-UPAdditional Information<

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

XL rear motor mount pad is the tall type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA

XL rear motor mount pad is the short type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA

Softail top frame plate features a raw steel finish, to match with seat area plate on 1986-1999 Softail original frames.For Hardtail installation. *NOTE: Align with the (2) 1/4" holes in plates. ...

FXR weld on top motor mount features a raw finish and is . for use on frame.Must be welded in place on FXRT and FLT models. Fits:FXR 1982-1990FLT 1980-1990Additional Information <

Beaded windshield is 21-3/4" tall and is for 1967-2010 Sidecars.Installation hardware not included, must be ordered separately. There are 5 mount holes altogether. Fits:FLT 1987-2010Additional...

Fork stem lock tab replace broken, bent or missing on stock lower triple trees, to be welded on. Fits:FLST 1987-1999Additional Information UOM1 - EA