1988

Jims - 96600-36B Valve Spring Compressor Tool fits '36-'04 Big Twin & '57-'03 Sportster Models Features: Comes with new valve collar receiver for safer tool usage, and can be clamped in vice Hardened ball bearing style tip at valve head end...

Jims - 97273-60 Camshaft Bearing Tool fits '57-'90 Sportster, '87-'90 Buell Models Features: Use to install inner cam bearings Made in the U.S.A. Fitment 1988-1990 Harley-Davidson Sportster 1200...

Jims - 94547-80B Sprocket Shaft Bearing Race Tool fits '77-'03 Sportster, '94-'02 Buell Models Features: Must use with JIMS® Race and Bearing Install Handle (PART# DS-196042) Used to remove and install Timken® bearing race on motor...

Jims - 97225-55 Sprocket Shift Bearing Installation Tool fits '55-'02 Big Twin Models Features: Used on '84-'02 Big Twin to install the flywheel assembly to the left crankcase Timken® bearing Made in the U.S.A...

Jims - 35820-86 Transmission Gear Spacing Tool fits '86-'90 Sportster, '87-'90 Buell Models Features: Used to align main and countershafts when checking proper gear spacing Made in the U.S.A. Fitment 1988-1990 Harley-Davidson Sportster...

Jims - 1743 Swingarm Bushing Tool fits '80-'01 FLT/​FLHT, '82-'99 FXR & all Aftermarket FXR-Style Frames Features: Allows installation of delicate, silicone cleveblock bushings in swingarm without damage Tool presses on outer sleeve of...

Jims - 34731-84 Valve Guide Installer fits all Evolution & '99-'04 Twin Cam Models (OEM #34731-84) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A...

Jims - 1047-TP Crank Assembly Removal Tool fits '55-'06 Big Twin Models (Except '06 Dyna) Features: This tool can only be used for removing the flywheel from the left case Will also press cases apart and break sealant bond Some case pressing will...

Jims - 1013-54TB Pin Bushing Installer fits '54-'92 Big Twin Models (OEM #25582-54/73) Features: Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking dowel pin Made...

Jims - 1017-37TB Cam Bushing Installer fits '37-'48 Big Twin Side-Valve Motors, '54-'20 Sportster, '91-'09 Buell Models (Except 1125R) Features: Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit...

Jims - 1030-TS Crank Pin Flywheel Socket fits 'L83-'99 Big Twin Models (OEM #23969-83) Features: Machined for 100% nut-to-socket and drive-end contact Eliminate nut rounding and risk of injury Made in the U.S.A...

Jims - 33071-73 Bearing Race Remover and Installer fits '73-'99 Big Twin, Sportster & Buell Wheels Features: Designed to remove and install bearing cups in cast wheels Use with JIMS® Handle Fitment 1999 Harley-Davidson Super...

Jims - 94660-37A Counter Shaft Sprocket Locknut Wrench fits '36-'06 Big Twin Models (Except '06 Dyna) Features: Removes hex nut from end of main drive gear that secures the rear drive transmission pulley Extra-long two-piece design Made in the...

Jims - 95760-TB Puller Camshaft Bearing fits '58-'99 Big Twin Models (Except Twin Cam) Features: Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with...

Jims - 95760-TP Pinion Bearing Puller fits '54-'99 Big Twin Models Features: Use to remove pinion bushing from cam cover in one easy operation Use with JIMS® Cam Cover Holder Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...

Jims - 95960-52C Clutch Hub Puller fits '36-'90 Big Twin Models Features: Used to remove wet and dry clutch hubs without removing clutch release rod 4 bolts included for dry clutch removal Made in the U.S.A...

Forbidden Motorcycles - Moto Style Handlebars 1" (1-1/8" Clamping Area) The Forbidden Motorcycles 1" Moto Style Bars feature a 1-1/8" clamping area but taper down to 1" to accommodate stock Harley hand controls, eliminating the need to sleeve them. They...

Custom Cycle Engineering - Swingarm Retrofit Kit fits '99-'01 FLT/​FLHT/​FLHR Models Features: Retrofits the improved swingarm from 02-08 Touring models to a 84-01 Touring models No need to alter transmission housing Will require the purchase of a...

Custom Cycle Engineering - Swingarm Retrofit Kit w/ Pivot Shaft fits '99-'01 FLT/​FLHT/​FLHR Models Features: Retrofits the improved swingarm from 02-08 Touring models to a 84-01 Touring models No need to alter transmission housing Will require the...

Custom Cycle Engineering - 41 mm Wide Glide Tweek Bar - Chrome Features: Original Randy Smith design As in the good old days with extended front tubes, the need for a tweek bar is here again Vast improvement over the tweek bars used in the 60s and...