1992

Engine bar features 1-1/4" tubing.Not for use with forward controls. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection...

Engine bar features 1-1/4" tubing, and 3 point mounting.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped,...

Passenger footboard set with swingarm mount kit includes streamline style mini footboards.A Wyatt Gatling patch is included in the kit. Installation will require re-installation of the original...

Chrome swingarm mount kit includes right & left side chrome pivot caps, passenger footboard mounts and passenger footboard with rubber pads.Installation will require re-installation of the original...

Raw steel hardtail rear frame section has replica forged axle plates for the exact look of the 1950's rigid frames. Accepts FXST oil tank, transmission mount plate and electric start.Hardtail for...

Left side caliper frame mount bracket for right side drive motorcycles must be welded on. Bracket is for rigid frames when mounting brake units. Fits:FLST 1987-1999FXST 1987-1999Additional Information

D+D XL raw rigid frame features a 1-1/4" thick wall, DOM steel tubing with 1-1/2" backbones, 30  rake and 0  stretch. This rigid frame is a basic starter frame.Frame will require custom 3/4" rear...

FXD raw weld on hardtail is easy to install as the alignment is accomplished in the mount design provided.Raw weld on hardtail uses a 14-1/2" rear axle, a chrome rear caliper kit and a battery box is...

Big Twin neck forgings machined to accept stock diameter tubing with 30  rake.Includes key lock tab and right hand number boss forged in neck. *NOTE: This frame neck does not include Manufacturer's...

Mid control mount kit is used to mount to the two holes located in the lower frame brace. Kit features a black finish.Mount features holes on each side for the left and right foot brake peg mount...

XL control mount set features a black finish. Control mounts for right (2 bolt plate) and left (3 bolt plate) to accept Big Twin forward controls.Set is used to mount 1941-1999 Big Twin forward mount...

V-Twin - 51-0484 - XL Hardtail Axle Plate SetDescriptionRaw set of right and left axle plates for Sportster hardtails, features 7/8" slots on both sides. Fits:XL 1982-UPAdditional Information<

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

XL rear motor mount pad is the tall type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA

XL rear motor mount pad is the short type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA

Softail top frame plate features a raw steel finish, to match with seat area plate on 1986-1999 Softail original frames.For Hardtail installation. *NOTE: Align with the (2) 1/4" holes in plates. ...

Beaded windshield is 21-3/4" tall and is for 1967-2010 Sidecars.Installation hardware not included, must be ordered separately. There are 5 mount holes altogether. Fits:FLT 1987-2010Additional...

Fork stem lock tab replace broken, bent or missing on stock lower triple trees, to be welded on. Fits:FLST 1987-1999Additional Information UOM1 - EA

Rear motor mount plate features a raw steel finish and is for use on custom frames. Fits:XL 1982-2003Additional Information UOM1 - EA

V-Twin - 51-0066 - Frame Motor Mount Tab RawDescriptionFrame motor mount tab must be welded on and features raw casting. Fits:XL 1982-UPAdditional Information

Rear motor mount frame plate features a raw steel finish and is for use on hardtails and custom frames. Fits:XL 1982-2003Additional Information UOM1 - EA

XL rigid frame neck is for the XL single loop rigid bobber frames. Fits:XL 1986-2003Additional Information UOM1 - EA

Rear motor mount casting features an investment cast construction and is for rigid frames. Fits:XL 1982-2003Additional Information UOM1 - EA <

V-Twin - 50-1910 - Sissy Bar Detachable Side Plates BlackDescriptionGloss black detachable side plates for easily adding or removing detachable accessories. Fits:FXST 1984-1999FLST 1986-1999 Except...

Fender tip set features a front and rear tip in a smooth style.Some drilling may be required for installation. Fits:FLSTF 1990-2006Additional Information OE

V-Twin - 50-1148 - Zinc Plated Fender BracketDescriptionZinc plated steel bracket used to adapt one piece FXDF front fenders to fit FLH forks on 1949-up 41mm models.Set of two. Bracket is formed from...

Chrome front fender mount kit attaches fender to original style assembly. Fits:FLST 1986-1999Additional Information UOM1 - KIT

Chrome front fender mount kit attaches fender to original style assembly. Fits:FXST 1984-1993Additional Information UOM1 - KIT

Rear fender bumper without grill. Fits:FLST 1986-1999Additional Information UOM1 - EA ManufacturerV-T

Bobbed rear fender kit includes steel fender and chrome tail lamp bracket which includes cateye tail lamp.We suggest pre fitting fender prior to painting. Order chrome struts and covers separately. ...

V-Twin - 50-0625 - XL Rigid Tool Box KitDescriptionLeft side tool box kit is the weld on type for rigid frames on Sportster builds.*NOTE: Weld bracket to lower rigid frame hardtail tube position or...

Rear fender kit includes steel fender, Replica chrome struts , chrome license plate bracket, and tail lamp with hardware.We suggest pre fitting the fender prior to painting. ...

Rear shorty fender features a primer finish. For Softail models.Fender does not includes tail lamp mount. Fits:FLST 1986-1999FXST 1986-1999Additional Information

Drag Specialties - DS380068 - OE Rear Fender - Raw Steel - '90-'95 FLSTFFeaturesAn exact steel replacementPre-drilled holes for fender struts, taillight and license plate mountReplacement Part for...

Drag Specialties - DS280219 - 8-1/4" Turn Signal Bracket - '85-'90 FLTFeaturesMounting brackets are 4-3/4" shorter than stock bracketsGive the rear of the bike a sleeker look; uses stock mounting...

Drag Specialties - DS223050 - Axle Kit - Rear - Chrome - '91-'99 DynaFeaturesKit includes axle, spacers, nuts and washersRear axle length is measured from the inside of the bolt head to the end of...

Drag Specialties - 78050076 - Regulator Cover - Chrome - '91-'03 XLFeaturesStamped steel cover fits over the existing regulatorIncludes chrome mounting hardwareReplacement Part for OEM...

Drag Specialties - 78050022 - Primary Shoe Adjuster - '91-'03 XLFeaturesIncludes bracket shoe and retaining clipZinc platedReplaces OEM adjusterReplacement Part for OEM Number(s):3242,3997091Specs

Drag Specialties - 78050015 - Clutch Pushrod End - Big TwinFeaturesStamped steel constructionIncludes oil slingerFor use with mechanical clutchesReplacement Part for OEM Number(s):3706990Specs

Drag Specialties - 78050013 - Regulator Cover - Chrome - '91-'03 FXDFeaturesStamped steel cover fits over the existing regulatorIncludes chrome mounting hardwareReplacement Part for OEM...