1994

Engine mount shim is used to raise motor for front or rear clearance, when necessary.Sold in a pack of 5. Fits:FL 1941-1999EL 1936-1952Additional Information

Engine bar features 1-1/4" tubing, and 3 point mounting.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped,...

V-Twin - 51-1322 - Lowered Rear Axle Plate Set RawDescriptionLowered rear axle plates are threaded 3/8"-18 for fender brace sissy bar mounting. Adjusters threaded 3/8"-24 use screws for adjusters, to...

Engine bar features integrated rubber pads for foot rests featuring a black finish.Does not include hardware. WARNING: This engine/frame bar may provide...

Engine bar features integrated rubber pads for foot rests featuring a chrome finish.Does not include hardware. WARNING: This engine/frame bar may...

Chrome left and right pivot mount end caps with footpeg mount holes.The OEM number for the right end cap is 50589-93, and the OEM number for the left end cap is 50588-93. Fits:FLT 1982-1984FLT...

Engine bar features 1-1/4" tubing.Includes bolts. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low...

Engine bar features 1-1/4" tubing.This engine bar is not for use with extended forward controls. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection...

Engine bar features 1-1/4" tubing and foot rests with rubber pads. Hardware is not included. This will not work with forward controls.**WARNING: This engine/frame bar may provide limited leg and...

Engine bar features 1-1/4" tubing.Not for use with forward controls. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection...

Engine bar features 1-1/4" tubing, and 3 point mounting.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped,...

Engine bar features 1-1/4" tubing and single top mount hole.Includes U-bolts, nuts, and straight bolt. The width between bottom mount plates measures 12" outside to outside. The height from the top...

Passenger footboard set with swingarm mount kit includes streamline style mini footboards.A Wyatt Gatling patch is included in the kit. Installation will require re-installation of the original...

Chrome swingarm mount kit includes right & left side chrome pivot caps, passenger footboard mounts and passenger footboard with rubber pads.Installation will require re-installation of the original...

Raw steel hardtail rear frame section has replica forged axle plates for the exact look of the 1950's rigid frames. Accepts FXST oil tank, transmission mount plate and electric start.Hardtail for...

Left side caliper frame mount bracket for right side drive motorcycles must be welded on. Bracket is for rigid frames when mounting brake units. Fits:FLST 1987-1999FXST 1987-1999Additional Information

D+D XL raw rigid frame features a 1-1/4" thick wall, DOM steel tubing with 1-1/2" backbones, 30  rake and 0  stretch. This rigid frame is a basic starter frame.Frame will require custom 3/4" rear...

FXD raw weld on hardtail is easy to install as the alignment is accomplished in the mount design provided.Raw weld on hardtail uses a 14-1/2" rear axle, a chrome rear caliper kit and a battery box is...

Big Twin neck forgings machined to accept stock diameter tubing with 30  rake.Includes key lock tab and right hand number boss forged in neck. *NOTE: This frame neck does not include Manufacturer's...

Mid control mount kit is used to mount to the two holes located in the lower frame brace. Kit features a black finish.Mount features holes on each side for the left and right foot brake peg mount...

XL control mount set features a black finish. Control mounts for right (2 bolt plate) and left (3 bolt plate) to accept Big Twin forward controls.Set is used to mount 1941-1999 Big Twin forward mount...

V-Twin - 51-0484 - XL Hardtail Axle Plate SetDescriptionRaw set of right and left axle plates for Sportster hardtails, features 7/8" slots on both sides. Fits:XL 1982-UPAdditional Information<

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

XL rear motor mount pad is the tall type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA

XL rear motor mount pad is the short type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA

Softail top frame plate features a raw steel finish, to match with seat area plate on 1986-1999 Softail original frames.For Hardtail installation. *NOTE: Align with the (2) 1/4" holes in plates. ...

Beaded windshield is 21-3/4" tall and is for 1967-2010 Sidecars.Installation hardware not included, must be ordered separately. There are 5 mount holes altogether. Fits:FLT 1987-2010Additional...

Fork stem lock tab replace broken, bent or missing on stock lower triple trees, to be welded on. Fits:FLST 1987-1999Additional Information UOM1 - EA

Rear motor mount plate features a raw steel finish and is for use on custom frames. Fits:XL 1982-2003Additional Information UOM1 - EA

V-Twin - 51-0066 - Frame Motor Mount Tab RawDescriptionFrame motor mount tab must be welded on and features raw casting. Fits:XL 1982-UPAdditional Information

Rear motor mount frame plate features a raw steel finish and is for use on hardtails and custom frames. Fits:XL 1982-2003Additional Information UOM1 - EA

XL rigid frame neck is for the XL single loop rigid bobber frames. Fits:XL 1986-2003Additional Information UOM1 - EA

Rear motor mount casting features an investment cast construction and is for rigid frames. Fits:XL 1982-2003Additional Information UOM1 - EA <

V-Twin - 50-1916 - Sissy Bar Detachable Side PlatesDescriptionGloss black side plates are detachable and can mount sissy bars with a width of 8-3/4".*NOTE: Must order hardware separately. Fits:FXDWG...

V-Twin - 50-1914 - Sissy Bar Detachable Side Plates BlackDescriptionGloss black detachable side plates for easily adding or removing detachable accessories. Fits:XL 1994-2003Additional Information

V-Twin - 50-1913 - Sissy Bar Detachable Side Plates BlackDescriptionGloss black side plates are detachable and can accept sissy bars with a width of 8-3/4".*NOTE: Must order hardware separately...

V-Twin - 50-1910 - Sissy Bar Detachable Side Plates BlackDescriptionGloss black detachable side plates for easily adding or removing detachable accessories. Fits:FXST 1984-1999FLST 1986-1999 Except...

XL Rear bobber fender features a ribbed design, constructed of black ABS plastic.*NOTE: Fender will not support a rear seat pad or sissy bar. Before priming or painting, fit the fender body, braces...

13" round sissy bar top features a black finish. Fits:XL 1994-2003Additional Information UOM1 - EA Manufacture

10" round sissy bar top features a black finish. Fits:XL 1994-2003Additional Information UOM1 - EA Manufacture