Touring Road King FLHR

Jims - 1275 Crankshaft Bearing Tool fits '99-'02 Twin Cam “A” Motors Features: Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in the U.S.A...

Jims - 74420-94 Electronic Speedometer Sensor fits '99-'03 FLT Model (OEM #74420-94, 74429-97, 74429-97A) Features: Top-quality replacement sensor Also works on any aftermarket transmission case with a speedometer sensor hole Includes O-ring,...

Jims - 970 3rd Hand Axle Locker Tool fits '02-'21 FLT/​FLHT Models Features: Eliminates the need for a helper or trying to blindly hold the axle from the other side of the tire Prevents axle from moving while torquing down the axle nut after setting...

Jims - 977 Fork Stem Nut Wrench fits '96-'13 FLHT & '94-'13 FLHR Models Features: This tool allows the ability to loosen, tighten and torque to spec the 1-1/2” stem nut without radio removal Normally to get access to the top stem nut...

Jims - 5822 Swing Arm Bearing Installer fits '02-'21 Touring Models Features: Both drive side and brake side bearings, which are at different depths, can be easily and accurately installed with this tool kit JIMS® took it one step further and...

Jims - 2232 Bearing Race Tool fits '84-'17 Big Twin (Except '14-'17 Dressers), '86-'22 Sportster & '94-'02 Buell OEM Frames (Will Also Work on Most Aftermarket Frames) Features: Removes and installs steering head bearing race on 84-16 Big Twin...

Jims - 96600-36B Valve Spring Compressor Tool fits '36-'04 Big Twin & '57-'03 Sportster Models Features: Comes with new valve collar receiver for safer tool usage, and can be clamped in vice Hardened ball bearing style tip at valve head end...

Jims - 97225-55 Sprocket Shift Bearing Installation Tool fits '55-'02 Big Twin Models Features: Used on '84-'02 Big Twin to install the flywheel assembly to the left crankcase Timken® bearing Made in the U.S.A...

Jims - 34731-84 Valve Guide Installer fits all Evolution & '99-'04 Twin Cam Models (OEM #34731-84) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A...

Jims - 94660-37A Counter Shaft Sprocket Locknut Wrench fits '36-'06 Big Twin Models (Except '06 Dyna) Features: Removes hex nut from end of main drive gear that secures the rear drive transmission pulley Extra-long two-piece design Made in the...

Jims - 1051 Wrist Pin Bushing Tool fits '99-'06 Twin Cam Models Features: Used to remove and install wrist pin bushings without removing connecting rods from crankcases Comes with instructions Made in the U.S.A...

Jims - 1283 Camshaft Chain Tensioner Tool fits '99-'06 Twin Cam Models (Except '06 Dyna) Features: Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams Also checks spring loads on chain...

Custom Cycle Engineering - Steering Damper System fits '99-'07 FLHR/​FLHT/​FLHTCU/​FLHX Models Features: This complete steering damper system stabilizes the front fork and helps prevent front-end wobble Custom-designed 1-1/4" clamp and bracket...

Custom Cycle Engineering - 41 mm Ultra Chrome Fork Tubes fits '99-'13 Touring (Except H-D FL Trike), '00-'17 Softail (Except FXS/​FXCW/​FXCWC), '00-'05 FXDWG Models (OEM #45890-97, 45930-00) Features: Designed to fit a wide variety of models Made in...