2002

Rear engine bar set with black finish. Set includes saddle bag supports, left and right guards, and hardware to replace the under the saddlebag support with loop style saddlebag guards for a...

Engine bar features 1-1/4" tubing.Includes bolts, nuts and washers. Must order clamps separately. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique...

Chrome left and right pivot mount end caps with footpeg mount holes.The OEM number for the right end cap is 50589-93, and the OEM number for the left end cap is 50588-93. Fits:FLT 1982-1984FLT...

Chrome engine bar features integrated rubber pads for foot rests.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while...

Chrome engine bar features integrated rubber pads for foot rests.The engine bar has a diameter of 1-5/16". **WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection...

Chrome swingarm for Softail models.Swingarm includes spherical bearings installed. Not for use on 2006-2007 FXST and 2007-up FLSTF. ...

Engine bar set features left and right sides with 1-1/4" tubing. For use with stock type saddle bag supports.2004-08 FLTR, FLHX, FLHRS models requires the seperate purchase of OEM #90781-93 Lower...

Rear frame set bar features left and right sides with 7/8" tubing.The stock shape reflectors are not included. *NOTE: Not for use with saddlebag rails. **WARNING: This frame bar may provide limited...

Engine bar features 1-1/4" tubing and foot rests with rubber pads. Hardware is not included. This will not work with forward controls.**WARNING: This engine/frame bar may provide limited leg and...

Engine bar features 1-1/4" tubing.Not for use with forward controls. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection...

Engine bar features 1-1/4" tubing and single top mount hole.Includes U-bolts, nuts, and straight bolt. The width between bottom mount plates measures 12" outside to outside. The height from the top...

Bar complements the traditional Touring style and features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over...

Chrome frame guard set includes left and right side with 7/8" tubing.*NOTE: Mounting hardware is not included, must be supplied by the installer. WARNING: This engine/frame bar may provide limited...

Black engine bar features integrated rubber pads for foot rests.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while...

Engine bar features a gloss black finish and integrated rubber pads for foot rests.Hardware is not included. The engine bar has a diameter of 1-5/16". **WARNING: This engine/frame bar may provide...

Passenger footboard set with swingarm mount kit includes streamline style mini footboards.A Wyatt Gatling patch is included in the kit. Installation will require re-installation of the original...

Chrome swingarm mount kit includes right & left side chrome pivot caps, passenger footboard mounts and passenger footboard with rubber pads.Installation will require re-installation of the original...

Chrome rear frame bar set. Top of the bar is angled downward to allow for more passenger leg room.*WARNING: This frame bar may provide limited leg and cosmetic vehicle protection under unique...

Profile frame bar set features left and right sides with 7/8" chrome plated tubing. For use with stock type saddlebag supports.The unique shape of these guards gives the passenger more leg room. Not...

D+D XL raw rigid frame features a 1-1/4" thick wall, DOM steel tubing with 1-1/2" backbones, 30  rake and 0  stretch. This rigid frame is a basic starter frame.Frame will require custom 3/4" rear...

Fairing outer shell is made from fiber reinforced plastic. This shell includes brass inserts to accept screws to mount to the inner fairing.This outer shell allows use of the stock hardware. ...

Gas tank mounting adapter kit allows 1984-1999 2 piece tanks to be mounted to 2000-up models and utilize original dash panel. Fits:FLST 2000-2017FXST 2000-2017Additional Information

Mid control mount kit is used to mount to the two holes located in the lower frame brace. Kit features a black finish.Mount features holes on each side for the left and right foot brake peg mount...

XL control mount set features a black finish. Control mounts for right (2 bolt plate) and left (3 bolt plate) to accept Big Twin forward controls.Set is used to mount 1941-1999 Big Twin forward mount...

V-Twin - 51-0484 - XL Hardtail Axle Plate SetDescriptionRaw set of right and left axle plates for Sportster hardtails, features 7/8" slots on both sides. Fits:XL 1982-UPAdditional Information<

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

XL rear motor mount pad is the tall type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA

XL rear motor mount pad is the short type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA

10" dark smoke Batwing fairing windshield. Fits:FLHT 1996-2013FLHX 1996-2013Additional Information OEM No.58303-96

7" dark smoked wind splitter windshield for the Batwing fairing is easy to install and gives the fairing a more stylish look while decreasing the wind noise. Constructed of Lexan material.NOTE: Does...

Engine bar features 1-1/4" tubing.Warning: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide). It...

10" clear Batwing fairing windshield.Reduces helmet buffeting while allowing a view unobstructed by dirt, bugs and raindrops. Constructed of hardcoated polycarbonate for strength and scratch...

Fairing air deflector set with dark smoke tint reduces draft behind the fairing.Designed to deflect air away from the driver's elbow and upper torso. *NOTE: The mounting hardware must be ordered...

Beaded windshield is 21-3/4" tall and is for 1967-2010 Sidecars.Installation hardware not included, must be ordered separately. There are 5 mount holes altogether. Fits:FLT 1987-2010Additional...

Rear motor mount plate features a raw steel finish and is for use on custom frames. Fits:XL 1982-2003Additional Information UOM1 - EA

V-Twin - 51-0066 - Frame Motor Mount Tab RawDescriptionFrame motor mount tab must be welded on and features raw casting. Fits:XL 1982-UPAdditional Information

Rear motor mount frame plate features a raw steel finish and is for use on hardtails and custom frames. Fits:XL 1982-2003Additional Information UOM1 - EA

XL rigid frame neck is for the XL single loop rigid bobber frames. Fits:XL 1986-2003Additional Information UOM1 - EA

Rear motor mount casting features an investment cast construction and is for rigid frames. Fits:XL 1982-2003Additional Information UOM1 - EA <

V-Twin - 50-2082 - Detachable Passenger Backrest Sissy Bar ChromeDescriptionDetachable passenger backrest sissy bar features a chrome finish. Fits:FLHT 1997-2008FLHR 1997-2008FLHX 1997-2008FLTR...