2002

James Gasket - Intake Manifold Gasket Kit fits '66-'84 Shovelhead, '57-'78 Sportster Models w/ Bendix/​Keihin (Butterfly Style (OEM #27002-57)) Features: Kit contains carb-to-intake seal and two intake-to-cylinder head...

Jims - 1746 Lockdown Axle Kit fits '99-'05 Dyna Models Features: Heavy-duty swingarm end caps and axle nut washer resist the bending and flexing seen with stock components Swingarm end caps fit more precisely into the end of the swingarm, providing...

Jims - 1747 Lockdown Axle Kit fits '86-'04 Sportster Models Features: Heavy-duty swingarm end caps and axle nut washer resist the bending and flexing seen with stock components Swingarm end caps fit more precisely into the end of the swingarm,...

Jims - 943 Ignition Switch Alignment Tool fits '03-'13 Touring & '02-'10 V-Rod Models Features: Also used to position switch in the correct orientation for properly activating the fork lock Proper alignment of the switch will extend the life of...

Jims - 942 Ignition Switch Connector Tool fits '03-'13 Touring & '02-'10 V-Rod Models Features: Slip the dog bone end of tool into the bottom side of connector until it is touching the back end of connector box Then gently pull out the male...

Jims - 939 Sealed Wheel Bearing Tool fits '00-'17 Twin Cam, '00-'22 Sportster & '02-'17 V-ROD Models Features: Removes and installs 3/4", 1" and 25 mm wheel bearing with or without Anti-Locking Brake System (ABS) Made in the U.S.A...

Jims - 767 6-Speed Transmission Case Shifter Shaft Seal Installer fits '06-'20 Big Twin & '84-'05 Sportster Models Features: Makes installing shifter shaft seal precise and effortless Aligns, centers and installs shifter seal to correct...

Jims - 768 5-Speed Transmission Case Shifter Shaft Seal Installer fits '80-'99 Big Twin, '99 Twin Cam, '99-'06 FXST & '99-'05 FLT/F LHT/​FXD Models Features: Makes installing shifter shaft seal precise and effortless Aligns, centers and...

Jims - 739 5 & 6-Speed Cruise Drive Countershaft Bearing Remover/Installer Tool Features: Install or remove the closed-end countershaft bearing on all 5-speed or 6-speed transmissions without using a press or tapping it in with a transmission...

Jims - 729 Inner Primary Seal/Bearing Removal/Installation Tool fits '85-'20 Big Twin Models Features: Gives a much better feel than a press while eliminating the possibility of applying too much pressure to the parts Provides precise installation...

Jims - 2268 Main Case Seal Installer Tool fits '85-'06 5-Speed Big Twin & Aftermarket 6-Speeds Models Features: Ensures correct alignment, seal protection and depth when installing the seal Made in the...

Jims - 5502 Ultimate Clutch Adjusting Tool fits '85-'20 Big Twins Models w/ Mechanical Clutch Features: Allows the quick and accurate tightening of the clutch adjusting screw jam nut without having the screw change position No more guessing or...

Jims - 5516 Sprocket Nut/Removal/Installation Socket Tool fits '91-'20 Sportster & Buell Models (Except Buell 1125R) Features: Ensures the mainshaft on Harley-Davidson® Sportster models extends through the guidance collar for correct...

Jims - 5518 Shifter Shaft Bushing Tool fits '85-'16 FLT Touring w/ 5- or 6-Speed Transmission Features: Time-saving tool removes worn shift shaft bushings in Big Twin primaries without having to remove he inner primary Tools installs new bushings to...

Jims - 967 Inner Primary Bearing and Seal Remover/Installer Tool fits 'L84-'06 FXST/​FLST & '85-'06 Touring & Dyna Models Features: Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer...

Jims - 976 Engine Rotator Tool fits '55-'06 Big Twin Models (Except '06 Dyna Glide) Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 2049 49 mm Fork Seal Installation Tool fits '06-'17 Dyna, '02-'11 V-Rod Models (Except Inverted Fork Models) Features: Installs lower leg 49 mm fork seals squarely into the bore without damaging the seal lip surface Designed for specific...

Jims - 5506 Magnetic Tappet Holder fits all Twin Cam & M-Eight Models Features: Never turn the engine over if the tappet will not spin with your fingers after adjustments were made It is very important that the engine is not rotated while...

Jims - 1664 5-Speed Transmission Shifter Shaft Sleeve Tool fits '80-'83 FLT/​FLHT/​FXR, '84-'99 Big Twins & '84-'00 FLHT/​FXR/​FXD Models Features: Can be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drum Use...

Jims - 5530 Remote Fuel Tank fits H-D Models w/ Delphi Fuel Injection (Except V-Rod) Features: Tank is completely mobile, even when pressurized; canister does not need to be continuously connected to the air supply Small enough to hang from a...

Jims - 1147 Alternator Rotor Puller fits '97-'06 Big Twin Models Features: A must-have tool for 45A charging systems; will also work on any Harley-Davidson® alternator system that has threaded puller holes Tool protects threads on sprocket shaft...

Jims - 2244 3/8" 35 mm Fork Nut Socket fits For Big Twin & Sportster Models Features: Used to remove and install top fork nuts on fork tubes Rubber protector inside socket Will clear most handlebars Made in the U.S.A...

Jims - 2240 Head Holder Guide Tool '48-'04 Big Twin, '57-'03 Sportster & Some SE CVO Twin Cam Models (5/16” Valve Guides) Features: Adapters are supported by a stand that makes it easy to press valve guides in and out A special guide...

Jims - 1146 Crankshaft Bearing Installer fits '00-'17 Twin Cam “B” Motors Models Features: Designed to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearing Made in the U.S.A...

Jims - 1162 Caliper Piston Remover fits '00-'07 Big Twin & '00-'03 Sportster 4-Piston Front/​Rear Calipers Models Features: Prevents damage to pistons and cylinders when installing new seals and wipers Holds pistons square in their cylinder...

Jims - 1167 Balancer Shaft/Removal Bearing Tool fits '00-'06 Twin Cam “B” Motors Models Features: Installing portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's bore Pulls the...

FLHRS Jims - 2043 41mm Fork Nut Socket fits '48-'17 Wide Glide Models Features: Eliminates possible burring of plug caused by wrenches Used to remove and install top fork-tube plug Fits 41 mm forks Made in the U.S.A...

Jims - 1705 Exhaust Drill Plate fits '84-'17 Big Twin (Except M-Eight), '86-'22 Sportster & '94-'09 Buell Models (Except 1125R) Features: Will position the seal evenly into the exhaust port of head Tool can be used with exhaust flange nuts Made...

Jims - 1034 Sprocket Shaft Holder fits '55-'99 Big Twin & '99-'06 Twin Cam (Except '06 Dyna) Features: Used to hold flywheel assembly in vise, with or without left case attached Made in the U.S.A...

Jims - 95760-57 Bushing Bearing Puller fits '66-'17 Big Twin (Except M-Eight), '57-'22 Sportster & Buell Models (Except 1125R) Features: Used to remove rocker bushing or bearing in one easy operation Made in the U.S.A...

Jims - 38515-90 Clutch Spring Compressor fits '90-'97 Big Twin & '91-'03 Sportster Models Features: For '91-'03 XL applications, compressor nut must be used in conjunction with compressor tool Used to release clutch spring so retainer ring can...

Jims - 38515-91 Nut Clutch Spring Compressor fits '91-'03 Sportster & Buell Models Features: For '91-'03 XL applications, compressor nut must be used in conjunction with compressor tool Used to release clutch spring so retainer ring can be...

Jims - 1710 Outer Race Snap Ring fits '69-'02 Big Twin Models Features: Used for removing and installing the Timken® bearing outer race snap ring A must for replacing rings in OEM and aftermarket cases Made in the U.S.A...

Jims - 33443-84 Tappet Aligning Tool fits 'L76-'17 Big Twin Models (Except M-Eight) Features: Can also be used to align rocker box bases on Evolution head (requires two tools) Also used in Harley-Davidson® Twin Cam oil pump alignment...

Jims - 1745 Bearing Simulator fits '70-'02 Big Twin Models Features: Designed to allow quick and easy removal and replacement of flywheel assembly in the left-side crankcase when checking rod-to-case, piston-to-flywheel or cylinder-to-flywheel...

Jims - 2260 Sprocket Lock Tool fits '99-'17 Twin Cam & '80-'99 Big Twin Models w/ Rear Belt Drive Features: Lock the transmission pulley for removing or installing pulley nut Made in the U.S.A...

Jims - 2189 Transmission Shaft Installer fits '83-'06 Big Twin Models Features: Installs transmission shaft without the use of a hydraulic or arbor press Made in the U.S.A. Fitment 2008 Harley-Davidson Fat Bob...

Jims - 1288 Crankshaft Guide fits '99-'17 Twin Cam & '03-'09 Buell XB9R/X B9S Models Features: Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A...

Jims - 1725 Head Bearing Race Installer fits '36-'17 Big Twin Models w/ Stock or Custom Frames (Except '14-'17 Dresser) Features: Use to install steering head races, stock and custom, as well as install cups in the frame This tool pulls the races...

Jims - 1709 Sprocket Shaft Bearing Tool fits '77-'02 Big Twin Models Features: Tool is used to remove the sprocket shaft Timken® bearing on late '86-'02 Big Twins with an integral sprocket shaft Does the job better than anything else on the...