2005

Jims - 1746 Lockdown Axle Kit fits '99-'05 Dyna Models Features: Heavy-duty swingarm end caps and axle nut washer resist the bending and flexing seen with stock components Swingarm end caps

Jims - 943 Ignition Switch Alignment Tool fits '03-'13 Touring & '02-'10 V-Rod Models Features: Also used to position switch in the correct orientation for properly activating the fork lock

Jims - 942 Ignition Switch Connector Tool fits '03-'13 Touring & '02-'10 V-Rod Models Features: Slip the dog bone end of tool into the bottom side of connector until it is touching the back end...

Jims - 939 Sealed Wheel Bearing Tool fits '00-'17 Twin Cam, '00-'22 Sportster & '02-'17 V-ROD Models Features: Removes and installs 3/4", 1" and 25 mm wheel bearing with or without Anti-Locking...

Jims - 767 6-Speed Transmission Case Shifter Shaft Seal Installer fits '06-'20 Big Twin & '84-'05 Sportster Models Features: Makes installing shifter shaft seal precise and effortless

Jims - 768 5-Speed Transmission Case Shifter Shaft Seal Installer fits '80-'99 Big Twin, '99 Twin Cam, '99-'06 FXST & '99-'05 FLT/F LHT/​FXD Models Features:

Jims - 739 5 & 6-Speed Cruise Drive Countershaft Bearing Remover/Installer Tool Features: Install or remove the closed-end countershaft bearing on all 5-speed or 6-speed transmissions without...

Jims - 729 Inner Primary Seal/Bearing Removal/Installation Tool fits '85-'20 Big Twin Models Features: Gives a much better feel than a press while eliminating the possibility of applying too much...

Jims - 2268 Main Case Seal Installer Tool fits '85-'06 5-Speed Big Twin & Aftermarket 6-Speeds Models Features: Ensures correct alignment, seal protection and depth when installing the seal

Jims - 5502 Ultimate Clutch Adjusting Tool fits '85-'20 Big Twins Models w/ Mechanical Clutch Features: Allows the quick and accurate tightening of the clutch adjusting screw jam nut withou

Jims - 5516 Sprocket Nut/Removal/Installation Socket Tool fits '91-'20 Sportster & Buell Models (Except Buell 1125R) Features: Ensures the mainshaft on Harley-Davidson® Sportster mo

Jims - 5518 Shifter Shaft Bushing Tool fits '85-'16 FLT Touring w/ 5- or 6-Speed Transmission Features: Time-saving tool removes worn shift shaft bushings in Big Twin primaries without havi

Jims - 1672 Crankshaft Bearing Tool fits '03-'17 Twin Cam “A” and “B” Motors Models Features: Designed to remove and replace the right crankcase bearing Press bearing in and out stra

Jims - 988 Valve Spring Compressor fits '05-'17 Twin Cam (Except SE Models), '04-'22 Sportster (Except RH Sportster) & Buell Models (Except 1125R) Features: Used to remove and replace valve and...

Jims - 967 Inner Primary Bearing and Seal Remover/Installer Tool fits 'L84-'06 FXST/​FLST & '85-'06 Touring & Dyna Models Features: Safely removes and installs inner primary bearing without any...

Jims - 976 Engine Rotator Tool fits '55-'06 Big Twin Models (Except '06 Dyna Glide) Features: Rotates flywheel/piston assembly with engine still in frame or on a bench

Jims - 2049 49 mm Fork Seal Installation Tool fits '06-'17 Dyna, '02-'11 V-Rod Models (Except Inverted Fork Models) Features: Installs lower leg 49 mm fork seals squarely into the bore without...

Jims - 956 Replacement Sleeve Timken Case Bearing Tool Features: Sleeve is several times stronger than stock aluminum case material that standard bearings ride in

Jims - 937 7mm Valve Guide Remover fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125R) Features: Available from JIMS to allow the proper removal or installation of...

Jims - 938 7mm Valve Guide Installer fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125CR) Features:

Jims - 5506 Magnetic Tappet Holder fits all Twin Cam & M-Eight Models Features: Never turn the engine over if the tappet will not spin with your fingers after adjustments were made

Jims - 1664 5-Speed Transmission Shifter Shaft Sleeve Tool fits '80-'83 FLT/​FLHT/​FXR, '84-'99 Big Twins & '84-'00 FLHT/​FXR/​FXD Models Features: Can be used to remove, install replacement or...

Jims - 5530 Remote Fuel Tank fits H-D Models w/ Delphi Fuel Injection (Except V-Rod) Features: Tank is completely mobile, even when pressurized; canister does not need to be continuously...

Jims - 1147 Alternator Rotor Puller fits '97-'06 Big Twin Models Features: A must-have tool for 45A charging systems; will also work on any Harley-Davidson® alternator system that has threaded...

Jims - 2244 3/8" 35 mm Fork Nut Socket fits For Big Twin & Sportster Models Features: Used to remove and install top fork nuts on fork tubes

Jims - 1146 Crankshaft Bearing Installer fits '00-'17 Twin Cam “B” Motors Models Features: Designed to protect engine cases by using a specially-designed support block to remove or install cam...

Jims - 1162 Caliper Piston Remover fits '00-'07 Big Twin & '00-'03 Sportster 4-Piston Front/​Rear Calipers Models Features: Prevents damage to pistons and cylinders when installing new

Jims - 1167 Balancer Shaft/Removal Bearing Tool fits '00-'06 Twin Cam “B” Motors Models Features: Installing portion is designed to push on the outer diameter of bearings preventing any damage to...

FLHRS Jims - 2043 41mm Fork Nut Socket fits '48-'17 Wide Glide Models Features: Eliminates possible burring of plug caused by wrenches Used to remove and install top fo

Jims - 1705 Exhaust Drill Plate fits '84-'17 Big Twin (Except M-Eight), '86-'22 Sportster & '94-'09 Buell Models (Except 1125R) Features: Will position the seal evenly into the exhaust port of...

Jims - 1034 Sprocket Shaft Holder fits '55-'99 Big Twin & '99-'06 Twin Cam (Except '06 Dyna) Features: Used to hold flywheel assembly in vise, with or without left case attached <

Jims - 95760-57 Bushing Bearing Puller fits '66-'17 Big Twin (Except M-Eight), '57-'22 Sportster & Buell Models (Except 1125R) Features: Used to remove rocker bushing or bearing in one easy...

Jims - 33443-84 Tappet Aligning Tool fits 'L76-'17 Big Twin Models (Except M-Eight) Features: Can also be used to align rocker box bases on Evolution head (requires two tools)

Jims - 2260 Sprocket Lock Tool fits '99-'17 Twin Cam & '80-'99 Big Twin Models w/ Rear Belt Drive Features: Lock the transmission pulley for removing or installing pulley nut

Jims - 2189 Transmission Shaft Installer fits '83-'06 Big Twin Models Features: Installs transmission shaft without the use of a hydraulic or arbor press

Jims - 1288 Crankshaft Guide fits '99-'17 Twin Cam & '03-'09 Buell XB9R/X B9S Models Features: Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel...

Jims - 1725 Head Bearing Race Installer fits '36-'17 Big Twin Models w/ Stock or Custom Frames (Except '14-'17 Dresser) Features: Use to install steering head races, stock and custom, as well as...

Jims - 2283 Transmission Door Puller fits '80-'06 Big Twin 5-Speed Models Features: Removes transmission door with gears and shaft attached

Jims - 1720 Main Bearing Remover fits '80-'06 Big Twin 5-Speed Transmissions Models Features: Removes old bearing straight and will not damage the transmission case

Jims - 2256 Drive Gear Seal Installation fits All 5-Speed Big Twin Models Features: Use to install main drive gear oil seal to the proper depth with transmission assembled Includes protecti