2007

Jims - 975 Engine Rotator Tool fits '07-'17 Twin Cam & '06 Dyna Glide Models Features: Rotates flywheel/piston assembly with engine still in frame or on a bench

Jims - 2049 49 mm Fork Seal Installation Tool fits '06-'17 Dyna, '02-'11 V-Rod Models (Except Inverted Fork Models) Features: Installs lower leg 49 mm fork seals squarely into the bore without...

Jims - 956 Replacement Sleeve Timken Case Bearing Tool Features: Sleeve is several times stronger than stock aluminum case material that standard bearings ride in

Jims - 937 7mm Valve Guide Remover fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125R) Features: Available from JIMS to allow the proper removal or installation of...

Jims - 938 7mm Valve Guide Installer fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125CR) Features:

Jims - 760K Socket Dipstick Insert Kit fits '07-'11 Touring & '06-'11 FXD Models Features: Simply install this insert in your existing JIMS dipstick socket tool and remove the finger grasp cap...

Jims - 5506 Magnetic Tappet Holder fits all Twin Cam & M-Eight Models Features: Never turn the engine over if the tappet will not spin with your fingers after adjustments were made

Jims - 1664 5-Speed Transmission Shifter Shaft Sleeve Tool fits '80-'83 FLT/​FLHT/​FXR, '84-'99 Big Twins & '84-'00 FLHT/​FXR/​FXD Models Features: Can be used to remove, install replacement or...

Jims - 5530 Remote Fuel Tank fits H-D Models w/ Delphi Fuel Injection (Except V-Rod) Features: Tank is completely mobile, even when pressurized; canister does not need to be continuously...

Jims - 2244 3/8" 35 mm Fork Nut Socket fits For Big Twin & Sportster Models Features: Used to remove and install top fork nuts on fork tubes

Jims - 1146 Crankshaft Bearing Installer fits '00-'17 Twin Cam “B” Motors Models Features: Designed to protect engine cases by using a specially-designed support block to remove or install cam...

Jims - 1162 Caliper Piston Remover fits '00-'07 Big Twin & '00-'03 Sportster 4-Piston Front/​Rear Calipers Models Features: Prevents damage to pistons and cylinders when installing new

FLHRS Jims - 2043 41mm Fork Nut Socket fits '48-'17 Wide Glide Models Features: Eliminates possible burring of plug caused by wrenches Used to remove and install top fo

Jims - 1705 Exhaust Drill Plate fits '84-'17 Big Twin (Except M-Eight), '86-'22 Sportster & '94-'09 Buell Models (Except 1125R) Features: Will position the seal evenly into the exhaust port of...

Jims - 95760-57 Bushing Bearing Puller fits '66-'17 Big Twin (Except M-Eight), '57-'22 Sportster & Buell Models (Except 1125R) Features: Used to remove rocker bushing or bearing in one easy...

Jims - 33443-84 Tappet Aligning Tool fits 'L76-'17 Big Twin Models (Except M-Eight) Features: Can also be used to align rocker box bases on Evolution head (requires two tools)

Jims - 2260 Sprocket Lock Tool fits '99-'17 Twin Cam & '80-'99 Big Twin Models w/ Rear Belt Drive Features: Lock the transmission pulley for removing or installing pulley nut

Jims - 2189 Transmission Shaft Installer fits '83-'06 Big Twin Models Features: Installs transmission shaft without the use of a hydraulic or arbor press

Jims - 1288 Crankshaft Guide fits '99-'17 Twin Cam & '03-'09 Buell XB9R/X B9S Models Features: Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel...

Jims - 1725 Head Bearing Race Installer fits '36-'17 Big Twin Models w/ Stock or Custom Frames (Except '14-'17 Dresser) Features: Use to install steering head races, stock and custom, as well as...

Jims - 1720 Main Bearing Remover fits '80-'06 Big Twin 5-Speed Transmissions Models Features: Removes old bearing straight and will not damage the transmission case

Jims - 2256 Drive Gear Seal Installation fits All 5-Speed Big Twin Models Features: Use to install main drive gear oil seal to the proper depth with transmission assembled Includes protecti

Jims - 2234 Primary Drive Lock Tool fits '70-'06 Big Twin & '86-'22 Sportster Models Features: Use on all primaries between front primary chain and motor sprocket

Jims - 39361-69 Sprocket Shaft Seal Installation Tool fits '69-'10 Big Twin & Twin Cam Models Features: Designed to press oil seal over sprocket shaft into case

Jims - 34902-84 Mainshaft Bearing Race Tool fits 'L84-'20 Big Twin Models Features: Used to remove and install the inner bearing race on the transmission mainshaft Made in the U.S.A.

Jims - 95970-32C Piston Pin Bush Tool fits '36-'99 Big Twin, '57-'20 Sportster & Buell Models (Except 1125R) Features: Use to remove and install wrist pin bushings without removing rods from...

Jims - 955 Gauge for Harley-Davidson Injection Pressure fits '01-'20 Big Twin Models w/ Delphi EFI (Except '18-'20 Softails) Features: Includes all necessary parts to diagnose Delphi fuel...

Jims - 970 3rd Hand Axle Locker Tool fits '02-'21 FLT/​FLHT Models Features: Eliminates the need for a helper or trying to blindly hold the axle from the other side of the tire Prevents axl

Jims - 977 Fork Stem Nut Wrench fits '96-'13 FLHT & '94-'13 FLHR Models Features: This tool allows the ability to loosen, tighten and torque to spec the 1-1/2” stem nut without radio removal

Jims - 5822 Swing Arm Bearing Installer fits '02-'21 Touring Models Features: Both drive side and brake side bearings, which are at different depths, can be easily and accurately installed with...

Jims - 2232 Bearing Race Tool fits '84-'17 Big Twin (Except '14-'17 Dressers), '86-'22 Sportster & '94-'02 Buell OEM Frames (Will Also Work on Most Aftermarket Frames) Features: Removes and...

Jims - 1017-37TB Cam Bushing Installer fits '37-'48 Big Twin Side-Valve Motors, '54-'20 Sportster, '91-'09 Buell Models (Except 1125R) Features: Use to install bushing and drill dowel pin hole to...

LA Choppers - Pinned Hefty Top Clamp fits '99-'23 Big Twin Models w/ 3-1/2 ” on Center Risers & Offset Mounting Holes Features: Fits Hefty handlebars and risers Polished aluminum construction

Custom Cycle Engineering - 49 mm Chrome Fork Brace fits '06-'17 FXD Model Features: Original Randy Smith design Manufactured from a solid piece of 6061 T-6 aluminum, then chrome-plated

Custom Cycle Engineering - 49 mm Chrome Fork Brace fits '06-'08 FXDWG, '08-'17 FXDF Models Features: Original Randy Smith design Manufactured from a solid piece of 6061 T-6 aluminum, then...

Custom Cycle Engineering - Steering Damper System fits '99-'07 FLHR/​FLHT/​FLHTCU/​FLHX Models Features: This complete steering damper system stabilizes the front fork and helps prevent front-end...

Custom Cycle Engineering - 41 mm Wide Glide Tweek Bar - Chrome Features: Original Randy Smith design As in the good old days with extended front tubes, the need for a tweek bar is here again

Custom Cycle Engineering - Adjustable Engine Mount fits '99-'17 Dyna Models (OEM #47226-93, 47226-99, 47226-90A) Features: Replace stock front engine bracket with custom slotted bracket with...

Custom Cycle Engineering - 41 mm Ultra Chrome Fork Tubes fits '99-'13 Touring (Except H-D FL Trike), '00-'17 Softail (Except FXS/​FXCW/​FXCWC), '00-'05 FXDWG Models (OEM #45890-97,...

Custom Cycle Engineering - 39 mm Ultra Chrome Fork Tubes fits '99-'05 FXDC/​FXDL/FXD & '87-'07 Sportster Models (Except XL1200S, '00-'05 FXDX/​FXDXT (OEM #45360-90)) Features: Designed to fit a...