2015

Jims - 987 Cruise Drive/6-Speed Main Bearing Installer Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Safely installs new main transmission case bearing; does not remove bearing Holds bearing square to its bore, eliminating any marring...

Jims - 984 Transmission Door Puller fits '07-'17 Big Twin & '06 Dyna Models Features: Removes transmission door with gears and shaft attached Made in the USA Puller will not damage door bearings...

Jims - 989 Main Drive Gear Sprocket Locknut Wrench fits '07-'21 Big Twin & '06 Dyna Models Features: Removes hex nut from end of main drive gear that secures the rear drive transmission pulley Extra-long two-piece design Made in the USA Inner...

Jims - Shifter Shaft Removal Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Loosens and removes both shifter shafts from transmission door, allowing further disassembly of transmission Made in the...

Jims - 939 Sealed Wheel Bearing Tool fits '00-'17 Twin Cam, '00-'22 Sportster & '02-'17 V-ROD Models Features: Removes and installs 3/4", 1" and 25 mm wheel bearing with or without Anti-Locking Brake System (ABS) Made in the U.S.A...

Jims - 901 Cruise Drive/6-Speed Main Drive Gear Remover Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Removes the main drive gear from the main bearing correctly while in the transmission case Eliminates the need of an arbor press and...

Jims - 911 Cruise Drive/6-Speed Trap Door Bearing Remover/Installer fits '07-'20 Big Twin & '06 Dyna Models Features: Accurately installs and removes lubed ball bearing into transmission trap door No arbor press needed Made in the U.S.A...

Jims - 767 6-Speed Transmission Case Shifter Shaft Seal Installer fits '06-'20 Big Twin & '84-'05 Sportster Models Features: Makes installing shifter shaft seal precise and effortless Aligns, centers and installs shifter seal to correct...

Jims - 1658 Transmission Shifter Shaft Sleeve Tool fits '06-'20 6-Speed H-D Cruise Drive Models Features: Can be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drum Use to install shifter shaft sleeve Made in the...

Jims - 739 5 & 6-Speed Cruise Drive Countershaft Bearing Remover/Installer Tool Features: Install or remove the closed-end countershaft bearing on all 5-speed or 6-speed transmissions without using a press or tapping it in with a transmission...

Jims - 729 Inner Primary Seal/Bearing Removal/Installation Tool fits '85-'20 Big Twin Models Features: Gives a much better feel than a press while eliminating the possibility of applying too much pressure to the parts Provides precise installation...

Jims - 967-4 Installation/Removal Inner Primary Bearing Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearing Also...

Jims - 967-5 Inner Primary Bearing Tool fits '07-'19 Big Twin & '06 Dyna Models Features: Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearing Also removes and installs...

Jims - 913 Wheel Bearing Support Plate Tool fits '14-'20 FL w/ Cast Wheels & '10-'20 CVO Models Features: Provides accurate and precise bearing removal and installation without the risk of damage to cast wheels Attaches to the brake rotor...

Jims - 5502 Ultimate Clutch Adjusting Tool fits '85-'20 Big Twins Models w/ Mechanical Clutch Features: Allows the quick and accurate tightening of the clutch adjusting screw jam nut without having the screw change position No more guessing or...

Jims - 5516 Sprocket Nut/Removal/Installation Socket Tool fits '91-'20 Sportster & Buell Models (Except Buell 1125R) Features: Ensures the mainshaft on Harley-Davidson® Sportster models extends through the guidance collar for correct...

Jims - 5517 Removal/Installation Shifter Mechanism Sleeve Tool fits '06 Dyna & '07-'20 Big Twin w/ 6-Speed Cruise Drive Transmission Features: A real time saver for removing and installing the shifter mechanism sleeve in cruise drive Big Twin...

Jims - 5518 Shifter Shaft Bushing Tool fits '85-'16 FLT Touring w/ 5- or 6-Speed Transmission Features: Time-saving tool removes worn shift shaft bushings in Big Twin primaries without having to remove he inner primary Tools installs new bushings to...

Jims - 5534 Compensator Bolt Driver Torx Socket fits '14-'21 Big Twin Models Features: Correct-style driver/socket for the compensating sprocket retaining fastener Made in the USA For use with Jim's part# 10500031 compensator bolt...

Jims - 900 6-Speed Main Drive Gear and Bearing Remover/Installer fits '06-'17 Touring, '06 Dyna & '07-'17 Softail Models Features: Complete kit for servicing the main drive gear or the main bearing on the latest Harley-Davidson­­®...

Jims - 1672 Crankshaft Bearing Tool fits '03-'17 Twin Cam “A” and “B” Motors Models Features: Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in...

Jims - 995 Case Splitter Tool fits '07-'17 Twin Cam & '06 Dyna Models Features: "Breaks" the case sealant by pushing apart both case halves Uses included hand thread-in pushing screw Flywheels will be pushed from the left case Bolts to primary...

Jims - 988 Valve Spring Compressor fits '05-'17 Twin Cam (Except SE Models), '04-'22 Sportster (Except RH Sportster) & Buell Models (Except 1125R) Features: Used to remove and replace valve and new-style conical valve spring Requires use of JIMS...

Jims - 969 Socket O² Sensor Tool fits '06 Dyna Glide & '07-'17 Twin Cam Models (Except 10-17 FLHT/​ FLHR/​FLHX/​FLTR, 11-17 FXST/​FLST/​FXS, 12-17 FXD/​FLD) Features: Remove and install oxygen sensors on fuel-injected models Socket tool...

Jims - 972 6-Speed Main Drive Gear Seal Installer fits all '07-'20 Big Twin & '06 Dyna Models Features: Use to install main drive gear oil seal to the proper depth with transmission assembled Includes protective sleeve for seal, which can be...

Jims - 975 Engine Rotator Tool fits '07-'17 Twin Cam & '06 Dyna Glide Models Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 2049 49 mm Fork Seal Installation Tool fits '06-'17 Dyna, '02-'11 V-Rod Models (Except Inverted Fork Models) Features: Installs lower leg 49 mm fork seals squarely into the bore without damaging the seal lip surface Designed for specific...

Jims - 937 7mm Valve Guide Remover fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125R) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made...

Jims - 938 7mm Valve Guide Installer fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125CR) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve...

Jims - 5506 Magnetic Tappet Holder fits all Twin Cam & M-Eight Models Features: Never turn the engine over if the tappet will not spin with your fingers after adjustments were made It is very important that the engine is not rotated while...

Jims - 5530 Remote Fuel Tank fits H-D Models w/ Delphi Fuel Injection (Except V-Rod) Features: Tank is completely mobile, even when pressurized; canister does not need to be continuously connected to the air supply Small enough to hang from a...

Jims - 5820 Standard Rear Axle Installation Guide Tool fits '08-'21 Big Twin w/ Hollow 1” (25 mm) Features: Aligns wheel with swingarm, caliper brackets, wheel hubs and spacers Made in the USA For Big Twin models with hollow 1" (25 mm)...

Jims - 2244 3/8" 35 mm Fork Nut Socket fits For Big Twin & Sportster Models Features: Used to remove and install top fork nuts on fork tubes Rubber protector inside socket Will clear most handlebars Made in the U.S.A...

Jims - 1146 Crankshaft Bearing Installer fits '00-'17 Twin Cam “B” Motors Models Features: Designed to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearing Made in the U.S.A...

FLHRS Jims - 2043 41mm Fork Nut Socket fits '48-'17 Wide Glide Models Features: Eliminates possible burring of plug caused by wrenches Used to remove and install top fork-tube plug Fits 41 mm forks Made in the U.S.A...

Jims - 1705 Exhaust Drill Plate fits '84-'17 Big Twin (Except M-Eight), '86-'22 Sportster & '94-'09 Buell Models (Except 1125R) Features: Will position the seal evenly into the exhaust port of head Tool can be used with exhaust flange nuts Made...

Jims - 95760-57 Bushing Bearing Puller fits '66-'17 Big Twin (Except M-Eight), '57-'22 Sportster & Buell Models (Except 1125R) Features: Used to remove rocker bushing or bearing in one easy operation Made in the U.S.A...

Jims - 33443-84 Tappet Aligning Tool fits 'L76-'17 Big Twin Models (Except M-Eight) Features: Can also be used to align rocker box bases on Evolution head (requires two tools) Also used in Harley-Davidson® Twin Cam oil pump alignment...

Jims - 2260 Sprocket Lock Tool fits '99-'17 Twin Cam & '80-'99 Big Twin Models w/ Rear Belt Drive Features: Lock the transmission pulley for removing or installing pulley nut Made in the U.S.A...

Jims - 1288 Crankshaft Guide fits '99-'17 Twin Cam & '03-'09 Buell XB9R/X B9S Models Features: Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A...