Harley Davidson

FXR kickstand mount bracket features a raw finish and must be welded in place. Accepts stock kickstand pin and spring. Fitment: FXR 1982-1994

Black exhaust bracket mounting block is for FXR models. Fitment: FXR 1982-1986

FXE rear exhaust mount kit includes a black bolt on style rear pipe bracket and zinc hardware. *NOTE: The bracket bolts to the pivot bolt hex bolts to replace the weld-on bracket. Fitment: FXR...

Zinc plated FXR front exhaust mount bracket. . Fitment: FXR 1986-1994

FXR horn mount bracket is the later version with a zinc plated finish. Tech Notes: Suggested to use with #33-2116 Replica Replacement Horn Black Fitment: FXR 1984-1994

Exhaust bracket for FXR models features a raw finish. Support bracket is welded to the frame to house the isolator block available separately. *NOTE: Must order hardware separately. Fitment: FXR...

FXRS raw steel dash bracket must be welded in place. Suggested to use with two 1/4 inchx 20 speed nuts. Tech Notes: Suggested to use with #39-0424 FXD-FXR Dash Panel Chrome Fitment: FXRS 1988-1994

FXR exhaust mount bracket. FXR exhaust mount bracket is mounted with (2) 7/16-20x1* pivot bolt cap screws. Our bracket mounting block can be bolted on to the opposing side using (2) 5/16-24x 5/8...

Battery strap clamp for FXR models features a black finish. Includes nut that is welded in place. Use with 1/4 x 20 bolt 1-1/2 inch hex head and 1/4 x 20 jam nut. Fitment: FXR 1984-1988 FXR 1990-1994

Rear exhaust bracket is zinc plated and for use with FXR models. *NOTE: Must order additional hardware: 5/16 inch x 3/4 inch x 1 inch spacer 5/16 inch-18 x 2 inch and 5/16 inch-18 x 1-3/4 inch allen...

FXR pipe bracket kit includes a raw weld on type bracket and an ISO mount block. *NOTE: Bracket must be welded on. Fitment: FXR 1982-1994

FXR chrome 35mm flat top stem nut fits 35 inch and 39 inch fork stems. Tech Notes: Suggested to use with #24-0827 Lower Triple Tree Chrome. Fitment: Fx 1978-1984 FXR 1982-1994 XL 1978-1987

Silver dash panel decal set. Sold as a 2 piece set. Fitment: FXR 1982-1994

Sold as a pair. Fitment: FXR 1982-1994

Rear axle adjuster has a 3/4 inch inner diameter and includes heavy pull blocks and two 1/4 inch-20 x 2 inch full thread allen cap screws. Fitment: FXR 1982-1994

Side cover for a 5-speed transmission clutch features a black finish. Fitment: FXR 1987-1994

WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped very low speed slide). They are not made nor intended to...

FXRP footboard control kit includes a brake pedal chrome footboard set zinc plated frame mount brackets and a heel-toe shifter lever. Fitment: FXR 1982-1994

FXR brake plunger kit is a three piece kit that includes a plunger rod end brake plunger end and hex nut in a zinc finish. Fitment: FXR 1987-1994

FXR inner shift washer and seal kit is for the 1/2 inch diameter inner shift shafts. Sold as a 6 piece kit. Fitment: FXR 1982-1984

FXR shifter shaft bushing includes 4 o-ring alloy type with two bronze bushings on each end. Sleeve is used to replace the stock plastic part. Fitment: FXR 1984-1994

FXR shifter rod assembly features a zinc finish and includes right and left hand ball ends with nuts. For use on FXR mid control shifter installation. Fitment: FXR 1982-1994

Zinc plated FXR pedal rod end 4 piece kit includes the rod end zinc clevis pin zinc 5/16 inch x 24 thread nut and a cotter pin. *NOTE: Measures 2-3/8 inch from the hole to the end of the thread...

FXR driver footpeg set features zinc plated peg shafts and includes the rubber set and mount bolt set. Sold as a pair. Fitment: FXR 1982-1994 XL 1986-2004

2023 New Production black kickstand is stock length and includes pin for FXR models. Fitment: FXR 1982-1990

FXRP shifter rubber set for heel toe shifter levers features a black finish and is the slip on type. Sold as a pair. Fitment: FXRP 1985-1994

FXR frame side cover set is constructed of black ABS plastic with vented panels. Sold as a pair. Requires (4) 1/4 inch-20 x 1-3/4 inch allen bolts and (4) 1/4 inch flat washers. Tech Notes: Required...

Axle spacer front for the right side and has an overall length of 1/2 inch. Measurements: Inner Diameter: 3/4 inches Fitment: FXD 1991-1996 FXR 1984-1994 XL 1986-2025

This is a plug and play type OEM replacement. *NOTE: Face graphics are aluminum color as original. Fitment: FLHR 2004-2013 FLHT 2004-2013 FXD 2004-2011 XL 2004-2013

Kelsey type chrome master cylinder with 3/4 inch bore and has inverted flair fitting. Measurements: Outer Diameter: 2-1/4 inches Fitment: FL 1979-1985 FLH 1979-1985

Remote master cylinder reservoir chrome cover with a finned design. Fitment: FL 1979-1984 Fx 1979-1984 XL 1979-1981

V-Twin - Handlebar Riser Cover for T-Bars - fits '14-Up Road King Models - Gloss Black Gloss black handlebar riser cover is for use with 1-1/4 inch one piece bars with 12 inch or 16 inch rise...

Replica Wagner style rear master cylinder for drum brake. The cast iron body is painted silver with a natural aluminum top. Master cylinder is 3/4 inch bore. NOTE: Wagner Lockheed replacement not...

Master cylinder is 3/4 inch bore. Tech Notes: Suggested to use DOT 5 fliud. Suggested to use with #23-1718 Rear Master Cylinder Rebuild Kit. Fitment: FL 1973-1978 Fx 1973-1978

This replaces the original plastic unit on the 1982-up models. Thread is 3/8 inch x 28 TPI. Holes on the back measure starting with the small one closest to the bottom and working to up: #8-32* 5/16...

Pro-One - Solid Riser Bushing Kit Features: CNC-machined from billet aluminum Removes handlebar slop associated with tall risers and handlebar setups

Pro-One - Pro V2 Floorboard Replacement Scrape Pad fits '99-'23 Touring, '09-'13 H-D FL Trike, '00-'17 FLST & '12-'16 FLD Models Features: Scrape pad for floorboads constructed from black...

Pro-One - Cable Custom Straight Rubber Cable Grips fits '99-'17 Twin Cam & '86-'22 Sportster Models (Except '08-'17 Dresser, H-D FL Trike, '16-'17 Softail, '13-'15 FXSBSE, '14-'15 FLSTNSE, '11-'12...

Pro-One - T-Rex Shorty Brake Arm fits '08-'13 FL Model Features: CNC machined billet aluminum construction Brake arm length is 6.25" / OEM = 8.8"

Pro-One - 41 mm Fork Tube Assemblies fits '00-'17 FXST/​FLST, '99-'05 FXDWG Models (Except FXSTD) Features: Assemblies come complete with fork tubes, springs, damping rods, bushings, clips,...