Engine

Jims - 975 Engine Rotator Tool fits '07-'17 Twin Cam & '06 Dyna Glide Models Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 976 Engine Rotator Tool fits '55-'06 Big Twin Models (Except '06 Dyna Glide) Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 937 7mm Valve Guide Remover fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125R) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made...

Jims - 5829 Cylinder Torque Plates fits '17-'20 M-Eight 107”, 114” Models Features: Torque plates must be used when boring or honing late-model aluminum cylinders Simulate running stress conditions Come with instructions Made in the U...

Jims - 5832 Ball Bearing Remover Tool fits '17-'20 Softail & Touring Models Features: Easily remove the balancer bearings in both Touring and Softail models without damage to the crankcase Fitment 2020-2021 Harley-Davidson Road...

Jims - 95660-77 4-Speed Seal Driver fits '82-'86 Big Twin Models Features: Optional drivers used in conjunction with main shaft seal tool allow installation of seals Fitment 1986 Harley-Davidson Softail Heritage...

Jims - 1146 Crankshaft Bearing Installer fits '00-'17 Twin Cam “B” Motors Models Features: Designed to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearing Made in the U.S.A...

Jims - 1167 Balancer Shaft/Removal Bearing Tool fits '00-'06 Twin Cam “B” Motors Models Features: Installing portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's bore Pulls the...

Jims - 1110 0.105" Camshaft Pinon Gauge Pins fits '54-'89 Big Twin Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 1989 Harley-Davidson Electra Glide Ultra...

Jims - 1111 0.108" Camshaft Pinion Gauge Pins fits '90-'99 Big Twin Evolution Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...

Jims - 33443-84 Tappet Aligning Tool fits 'L76-'17 Big Twin Models (Except M-Eight) Features: Can also be used to align rocker box bases on Evolution head (requires two tools) Also used in Harley-Davidson® Twin Cam oil pump alignment...

Jims - 1288 Crankshaft Guide fits '99-'17 Twin Cam & '03-'09 Buell XB9R/X B9S Models Features: Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A...

Jims - 34623-83 Piston Pin Tool fits '84-'99 Big Twin (Except Twin Cam), '86-'03 Sportster Models Features: This tool will install “Round Circlip” rings in one easy step without distorting ring, for the safest wrist pin retention...

Jims - 34643-84 Valve Seal Installer for all Evolution Valve Guide Seals (OEM #34643-84) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A...

Jims - 1010 Evolution Rod Alignment Tool for 0.791” Wrist Pin Features: Use to check rod straightness without removing the rods from the cases Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...

Jims - 94805-57 Pinion Bushing Line Reamer fits '54-'99 Big Twin Models (Except Twin Cam) Features: Use on all Big Twin '54-'99 single cam only, (NOTE: Includes aftermarket motors, also XL '57 to early '84 idler gear bushing) Designed to line-ream...

Jims - 1041-TC Camshaft Cover Holder Tool fits '70-'99 Big Twin Models (Except Twin Cam) Features: Holds cam cover flat and helps prevent damage/scratches when removing and installing bushings Clamps in vice or Bridgeport™ mill Made in the U...

Jims - 95970-32C Piston Pin Bush Tool fits '36-'99 Big Twin, '57-'20 Sportster & Buell Models (Except 1125R) Features: Use to remove and install wrist pin bushings without removing rods from crankcase Made in the U.S.A...

Jims - 96600-36B Valve Spring Compressor Tool fits '36-'04 Big Twin & '57-'03 Sportster Models Features: Comes with new valve collar receiver for safer tool usage, and can be clamped in vice Hardened ball bearing style tip at valve head end...

Jims - 34731-84 Valve Guide Installer fits all Evolution & '99-'04 Twin Cam Models (OEM #34731-84) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A...

Jims - 1047-TP Crank Assembly Removal Tool fits '55-'06 Big Twin Models (Except '06 Dyna) Features: This tool can only be used for removing the flywheel from the left case Will also press cases apart and break sealant bond Some case pressing will...

Jims - 1030-TS Crank Pin Flywheel Socket fits 'L83-'99 Big Twin Models (OEM #23969-83) Features: Machined for 100% nut-to-socket and drive-end contact Eliminate nut rounding and risk of injury Made in the U.S.A...

Jims - 1283 Camshaft Chain Tensioner Tool fits '99-'06 Twin Cam Models (Except '06 Dyna) Features: Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams Also checks spring loads on chain...

Custom Cycle Engineering - 41 mm Wide Glide Tweek Bar - Chrome Features: Original Randy Smith design As in the good old days with extended front tubes, the need for a tweek bar is here again Vast improvement over the tweek bars used in the 60s and...

Drag Specialties - 3-1/4" Chrome Magnetic Ring Oil Filter fits '86-'22 Sportster (Except RH Sportster), '09-'12 XR1200/X Models (OEM #63806-83, 63796-77A, 63805-80A) Features: High-quality chrome spin-on-style oil filters Magnetic filters are...

Drag Specialties - Oil Filter fits '86-'22 Sportster (Except RH Sportster), '09-'12 XR1200/X Models (OEM #63806-83, 63796-77A, 63805-80A) Features: High-quality spin-on filters are a dependable...

V-Twin - Panhead Style Evolution Rocker Box Set fits '84-'99 FXST/FLST, '84-'98 FLT/FXD Models - Chrome Panhead Evolution rocker box set features a bolt on Panhead look for Evolution models and a chrome finish. Retro conversion kit includes chrome...

V-Twin - Panhead Style Evolution Rocker Box Set fits '84-'99 FXST/FLST, '84-'98 FLT/FXD Models - Black Panhead Evolution rocker box set features a bolt on Panhead look for Evolution models and a black finish. Retro conversion kit includes black Panhead...

S&S Cycle - Stock Heads Intake Manifold O-Ring fits '84-'16 Big Twin, '86-'16 Sportster Models (OEM #26992-99, 26995-86A) Features: Sold Each Made from the highest-quality materials available Made in the USA Replacement Part for...

S&S Cycle - Billet Oil Pump Kit fits '92-'99 Evolution Big Twin Models Features: Kit includes an oil pump with cover, mounting bolts, supply and return gears, drive shaft with keys and snap rings, check ball and spring, pressure relief valve and...

S&S Cycle - Billet Oil Pump fits '70-'91 Big Twin Models Features: Kit includes an oil pump with cover, mounting bolts, supply and return gears, drive shaft with keys and snap rings, check ball and spring, pressure relief valve and spring, check...

S&S Cycle - Replacement Billet Oil Pump Gasket Kit Features: Made in the U.S.A. Fitment 1999 Harley-Davidson Super Glide Sport FXDX - - 1999 Harley-Davidson FXR 3 - - 1999 Harley-Davidson FXR...

S&S Cycle - Oil Pump Replacement Gasket Kit fits '36-'69 Big Twin Models Features: Made in the U.S.A. Fitment 1991 Harley-Davidson Dyna Sturgis FXDB - - 1990-1991 Harley-Davidson Low Rider Convertible...

S&S Cycle - Rocker Arm Shafts fits '99-'17 Twin Cam & '86-'22 Sportster Models (Except RH Sportster (OEM #17611-83)) Features: Made in the U.S.A. Fitment 2018-2020 Harley-Davidson Iron 1200...

S&S Cycle - Rocker Box Gasket Kit fits EVO Big Twin Models Features: Replacement gasket kit for rocker box part number 90-4095 Fitment 2000 Harley-Davidson FXR 4 - - 1999 Harley-Davidson Softail Night Train...

S&S Cycle - Rocker Box Gasket Kit fits Twin Cam Models Features: Includes all required gaskets and O-rings for both rocker boxes Fitment 2017 Harley-Davidson Road King Special FLHRXS - - 2016-2017 Harley-Davidson CVO Pro...

S&S Cycle - Compression Release Hole Plug Features: Not for use on OEM heads Made in the U.S.A. Fitment 2016-2017 Harley-Davidson Fat Boy S FLSTFBS - - 2016-2017 Harley-Davidson Softail Slim S...

S&S Cycle - Adjustable Pushrods fits '99-'17 Twin Cam Models Features: .4375" diameter chromoly steel for maximum strength Rocker boxes must be removed for installation or removal Made in the U.S.A...

S&S Cycle - Tappet Alignment Tool fits 'L76-'17 Big Twin Models (Except M-Eight) Features: Big Twin Evolution tappet blocks do not have counter-bored bolt holes; therefore, when a tappet block is removed (or even just loosened) it should be...

S&S Cycle - Rocker Cover Wrench Set Features: Four wrenches of different lengths for those hard-to-get-to rocker box screws For use on all Big Twin and XL Evolution-style motors Made in the U.S.A...