Engine

Jims - 1278-3 Camshaft Bearing Installation fits '99-'17 Twin Cam Models Features: Replacement drive for JIMS® Cam Bearing Installation Tool

Jims - 917 Pushrod Cover Clip Features: Will install and remove the clip professionally with just one hand in seconds This tool will NOT marr or slip Made in the U.S.A.

Jims - 910 Piston Ring Compressor Set for Sizes From 1 7/8” To 2 7/8” - Set Of 4 Features: Fine-tooth ratcheting motion will compress the bands in small increments for accurate compression Will not break or damage rings Made in the U.S...

Jims - 782 4-Stroke Dual Gauge Leakdown Tester Features: Tool troubleshoots cylinder leakdown issues such as valve seat issues, bad rings and bad head gasket Hose assembly has both 14 mm and 18 mm spark plug threads Includes 12 mm and 10 mm...

Jims - 780 Seal Leak Tester Tool fits '00-'17 Twin Cam “B” Motors Model Features: Required to seal the oil passage way from right case to the balancer tensioner plate; leaking can cause over oiling of the lower end that decreases...

Jims - 1090 Mini Valve Spring Tester Features: Tool fits any dual rate or conical valve spring with an O.D. no larger then 1.6” diameter Works with bench vise, arbor, screw hydraulic or drill press 0 to 1000 P.S.I. gauge Made in the U.S.A.

Jims - 902 Blue Motor Stand fits '00-'17 Twin Cam “B” Motor Model Features: Makes working on motors easier with better access Made in the USA Note: For Twin Cam "B" motor.

Jims - 941 Slim Oil Filter Wrench Features: An exclusive design makes it much easier to navigate when working near both the oil cooler and the crankcase position sensor Allows you more room to work around exhaust pipes, frame, hoses and...

Jims - 3200 Flange Piston Ring End Gap Tool for H-D 95”,103” & 110” Motors w/ Standard Size Pistons (3.875” or 4” Bore) Features: This tool makes measuring ring end gap faster, more accurate and eliminate the guess...

Jims - 746 Go-No-Go Hydraulic Tappet Tool Features: Only when the tip fits nicely with no endplay is the tappet properly adjusted, if the tip doesn’t fit, OR if there is up and down endplay, the tappet is out of adjustment After adjusting the...

Jims - 1042-7 Expander Dowel Tool fits All '00-'17 Twin Cam, '00-'22 Sportster & '02-'17 V-Rod Models Features: Removes and installs 3/4", 1", and 25 mm wheel bearings with or without (Anti-Lock Brake System) ABS Made in the U.S.A.

Jims - 1236 Piston Ring Compressor Kit for Sizes From 2 7/8” to 4 3/ 8” - Set Of 6 Features: Fine-tooth ratcheting motion will compress the bands in small increments for accurate compression Will not break or damage rings Made in the U...

Jims - 5800 Flywheel Puller Tool fits '15-'16 Indian Scout Model Features: Eliminates potential damage to the flywheel when used in this application Ensures good and solid engagement when using the puller Made in the U.S.A...

Jims - 5805 Wrist Pin Remover Tool fits '17-'21 M-Eight Models Features: Quickly and easily removes wrist pins from Milwaukee-Eight® engines Adapter part for JIMS® Wrist Pin Tool (PART# DS-196197) Made in the U.S.A.

Jims - 5809 Cylinder Hold Down Tool fits '17-'20 M-Eight & '99-'17 Twin Cam Models Features: Useful when installing the second cylinder over the piston and rings after the first cylinder has been installed One end fits Twin Cam models, while the...

Jims - 5811 Balancer Scissor Gear Tool fits '17-'20 M-Eight Models Features: Holds 2 halves of spring-loaded balancer scissor gear in alignment before removal Bright color reminds technician to remove it before sealing engine case For use on the...

Jims - 5829 Cylinder Torque Plates fits '17-'20 M-Eight 107”, 114” Models Features: Torque plates must be used when boring or honing late-model aluminum cylinders Simulate running stress conditions Come with instructions Made in the U...

Jims - 5830 Left Main Seal Remover Tool fits '17-'21 M-Eight Models Features: For use on Milwaukee Eight series engines

Jims - 775 Removal/Installation Main Seal Tool fits '99-'17 Twin Cam Models Features: Install and remove crank case main seal while the engine is still in the chassis Includes necessary adapters for '88 and '96 Twin Cams Made in the U.S.A.

Jims - 5834 Engine Stand fits '18-'21 M-Eight Softail Models Features: For use on the Milwaukee Eight™ engine series JIMS Milwaukee-Eight® Softail® engine stand is designed to work on all Milwaukee-Eight® Softail engines JIMS...

Jims - 5832 Ball Bearing Remover Tool fits '17-'20 Softail & Touring Models Features: Easily remove the balancer bearings in both Touring and Softail models without damage to the crankcase Fitment 2020-2021 Harley-Davidson Road...

Jims - 760K Socket Dipstick Insert Kit fits '07-'11 Touring & '06-'11 FXD Models Features: Simply install this insert in your existing JIMS dipstick socket tool and remove the finger grasp cap easily with no chance of damage This insert,...

Jims - 5838 Oil Pump Alignment Tool fits '17-'21 M-Eight Engines Models Features: This tool was designed to help the technician assemble the complete cam chest correctly, in a quick and efficient manner The perfect aid for the technician to either...

Jims - 991 Case Splitting Tool fits '18-'21 M8 Softail & Touring Models Features: In order to perform any type of lower end service or performance work, it is necessary to split the crankcase into halves Simply install the tool on the primary...

Jims - 5506 Magnetic Tappet Holder fits all Twin Cam & M-Eight Models Features: Never turn the engine over if the tappet will not spin with your fingers after adjustments were made It is very important that the engine is not rotated while...

Jims - 730 Piston Tester Jet fits '18-'21 M-Eight Softail Models Features: Assists engine rebuilder to clear jet of all assembly lubes; verifies psi number the jet switches to "on" and visualizes spray pattern before cases are sealed Helps determine...

Jims - 1284 Connecting Rod Holding Tool for Most V-Twin & Buell Blast Applications Features: Holds the rods in place when reaming or honing the wrist pin bushings Made in the USA For most V-Twin and Buell Blast applications.

Jims - 95660-77 4-Speed Seal Driver fits '82-'86 Big Twin Models Features: Optional drivers used in conjunction with main shaft seal tool allow installation of seals Fitment 1986 Harley-Davidson Softail Heritage...

Jims - 1146 Crankshaft Bearing Installer fits '00-'17 Twin Cam “B” Motors Models Features: Designed to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearing Made in the U.S.A...

Jims - 1167 Balancer Shaft/Removal Bearing Tool fits '00-'06 Twin Cam “B” Motors Models Features: Installing portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's bore Pulls the...

Jims - 1110 0.105" Camshaft Pinon Gauge Pins fits '54-'89 Big Twin Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 1989 Harley-Davidson Electra Glide Ultra...

Jims - 1111 0.108" Camshaft Pinion Gauge Pins fits '90-'99 Big Twin Evolution Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...

Jims - 2392 Head Bolt Torque Gauge fits all Twin Cam & Evolution Engines Models Features: This accurate gauge allows the measuring of 90° when tightening head bolts Torquing sequence laser engraved on gauge, with instructions Works on all...

Jims - 1052 Oil Pump Snap Ring Installer fits Big Twin Oil Pumps (Except Twin Cam/M-Eight) Features: Just apply oil to ring expander, slip ring up to the big end of ring expander, hold up to the end of the shaft, then push ring onto the shaft with...

Jims - 1053 Oil Pump Seal Installer fits Big Twin Aluminum Oil Pumps (Except Twin Cam/M-Eight) Features: For use on all Big Twin aluminum oil pumps (except Twin Cam/M8) Easily installs oil pump seal below gear surface for a no-leak fit Made in the...

Jims - 33443-84 Tappet Aligning Tool fits 'L76-'17 Big Twin Models (Except M-Eight) Features: Can also be used to align rocker box bases on Evolution head (requires two tools) Also used in Harley-Davidson® Twin Cam oil pump alignment...

Jims - 1288 Crankshaft Guide fits '99-'17 Twin Cam & '03-'09 Buell XB9R/X B9S Models Features: Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A...

Jims - 1001 Valve Guide Driver Set Features: Three piece set (3/8", 1/32", 5/16") used to remove or install valve guides Designed for guide removal and installation on all models Made in the U.S.A.

Jims - 34623-83 Piston Pin Tool fits '84-'99 Big Twin (Except Twin Cam), '86-'03 Sportster Models Features: This tool will install “Round Circlip” rings in one easy step without distorting ring, for the safest wrist pin retention...

Jims - 34740-84 Valve Guide Remover for all Evolution & '99-'04 Twin Cam Guides Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.