Sportster XLH1000

Rear upper shock stud kit includes 4 cup washers and 2 studs. Fits:XL 1956-1974Additional Information OEM No.54515-56B

H-12 battery cast is plastic as original battery, with a removable top. Kit features a mock plastic top that will house most smaller batteries and mounts like an original battery.Mock battery box is...

H-12 battery top cover with terminals. Fits:FL 1965-1984XL 1967-1978Additional Information UOM1 - EA

V-Twin - 53-0501 - 12 Volt AGM H-12 Sealed Battery BlackDescriptionAbsorbed Glass Mat technology proposes the best balance between cold cranking amps and amp hour capacity.AGM battery is fully sealed...

16" x 3.00" rear wheel and brake drum assembly includes an all chrome wheel, brake drum, chrome backing plate and chrome axle kit.Order chrome brake arm separately. ...

16" x 3.00 rear wheel assembly with chrome hub and bearings installed, black rim, and chrome spokes.*NOTE: The valve stem hole is on the sprocket side. **NOTE: All spokes on wheel need to be...

18" x 2.15" wheel assembly includes a 40 hole chrome rim, 21 cadmium spokes and a black rear hub, with all internal installed, laced and trued.Accepts a 400-450 x 18" tire. *NOTE: All spokes on wheel...

These rear wheel assemblies start with a 40 hole 18" x 2.5" chrome rim, single flange, 40 stainless spokes and a rear hub.Wheel is laced and trued. Accepts a 130-140 tire size. ...

Rear wheel assembly include a 18" x 2.5" chrome rim, 40 chrome spokes, and a rear hub. Wheel is laced and trued. Accepts a 130-140 tire size.NOTE: All spokes on wheel need to be inspected and...

This rear 18" x 2.15" wheel assembly includes a 40 hole chrome rim, 40 stainless steel spokes and a rear hub with bearings installed, laced and trued. Accepts a 130-140 tire size.NOTE: All spokes on...

Rear wheel assembly includes 18" x 2.15" chrome conventional style rolled rim, 40 chrome spokes and a rear hub. Wheel is laced and trued. Accepts a 100-120 tire size.NOTE: All spokes on wheel need to...

Features a 16" x 3.00" drop center rim with a large valve stem hole, 40 chrome twirled spokes and a hub with bearings installed.NOTE: All spokes on wheel need to be inspected and re-torqued after 500...

These rear wheel assemblies start with a 40 hole 16" x 3" chrome rim, 40 polished stainless steel spokes and a rear hub with bearings installed. Accepts a 130-140 tire size.NOTE: All spokes on wheel...

V-Twin - 52-0301 - 19 inch X 2.50 inch Wheel Rim and Spoke Kit ChromeDescriptionRim and spoke set include 19" x 2.50" front rim with 40 chrome spokes with 40 spoke nipples.Rim is steel and drop...

16" x 3.00 rear wheel assembly with chrome hub and bearings installed, chrome rim, and chrome spokes.*NOTE: The valve stem hole is on the sprocket side. **NOTE: All spokes on wheel need to be...

Replica 19" X 2.50" single disc front clover style wheel feature a chrome drop center hub with internal bearings installed, 40 chrome spokes and chrome rim.**NOTE: All spokes on wheel need to be...

Replica 21" X 1.85" single disc front clover type wheel features a chrome hub with internal bearings installed, 40 chrome spokes and chrome rim.**NOTE: All spokes on wheel need to be inspected and...

200 XL rigid frame features a 40  rake with a 3" stretch in front legs to accept a 1-1/8" belt with 200 series tire.Frame has kickstand tab and battery box mount welded in place. Accepts a right side...

Footpeg support bar set is the splined type featuring a raw steel construction.Attaches to early Sportster frames to mount footpeg stanchions. One end is splined and the other fits over the frame...

Raw steel weld-on hardtail features a raw steel finish.Replaces entire rear section of the frame, for the full rigid look. *NOTE: Must be installed by a certified welder. Fits:XL 1957-1978Additional...

Frame hardtail is weld on type and includes weld on frame plate. Accepts drum type brake.Hardtail should be aligned for chain clearance prior to final welding. This hardtail fits hardtail rigid...

Frame hardtail is bolt on type. Accepts drum style brakes on a rigid frame.Unit should be aligned for chain clearance prior to final bolting. DIY hardtail is easy to install as the alignment is...

XL brake cross shaft kit includes two bushings. Kit must be welded in place. Fits:XL 1952-1976Additional Information UOM1 - KIT

This raw steel full rear section hardtail for Sportsters includes the rear motor mount and 4 bolt plate mount with upper and lower tube set. Frame is used to replace the stock rear motor mount and...

Frame mount tab set for solo seats have weld on mount tabs. Use with T bar and pivot bolt to mount K and CH solos. Fits:XL 1957-1979Additional Information UOM

Neck frame casting fits XL models to be welded in place on 30  stock or custom frames. Has unmachined padlock boss. Accepts neck cup kit.Neck frame accepts stock bearing cups and trees. Fits:XL...

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

XL raw brake shaft tube for mechanical brakes. Kit includes machined 7.25" tube with brass bushing and shifter cross bushing set installed. Must be welded in place to frame.*NOTE: Locate tube using...

Bobbed rear fender kit includes a steel fender, cateye tail lamp, chrome tail lamp bracket, and chrome struts.We suggest pre fitting fender prior to painting. Order sissy bar components separately. ...

V-Twin - 50-0625 - XL Rigid Tool Box KitDescriptionLeft side tool box kit is the weld on type for rigid frames on Sportster builds.*NOTE: Weld bracket to lower rigid frame hardtail tube position or...

Drag Specialties - DS902016 - Solo Seat Mounting Bracket - XL '57-'78 Features Chromed bracket for Harley® rigid frame XL models 7" on-center spring mounts Not for XLCR models. Specs

Drag Specialties - DS750755 - Piston - XLFeaturesOEM quality cast aluminum alloy constructionSome fitments feature pistons with a coating that extends piston life, reduces friction and allows for...

Drag Specialties - DS750754 - Piston - XLFeaturesOEM quality cast aluminum alloy constructionSome fitments feature pistons with a coating that extends piston life, reduces friction and allows for...

Drag Specialties - DS750753 - Piston - XLFeaturesOEM quality cast aluminum alloy constructionSome fitments feature pistons with a coating that extends piston life, reduces friction and allows for...

Drag Specialties - DS750752 - Piston - XLFeaturesOEM quality cast aluminum alloy constructionSome fitments feature pistons with a coating that extends piston life, reduces friction and allows for...

Drag Specialties - DS750751 - Piston - XLFeaturesOEM quality cast aluminum alloy constructionSome fitments feature pistons with a coating that extends piston life, reduces friction and allows for...

Drag Specialties - DS720814 - Fender License Plate Mount - ChromeFeatures4" x 7" mount includes dual rubber gaskets, allowing the angle of the mount to be raised or lowered as neededIncludes all...

Drag Specialties - DS390131 - Gas Cap - Non-Vented - ChromeFeaturesReplacement gas caps for OEM and custom tanksWill not fit screw-in type tanks.Replacement Part for OEM Number(s):6110373Specs

Drag Specialties - DS380201 - Spoke Set - Drop Center - Front/Rear - Stainless Steel - 16"FeaturesStrong, quality spoke sets used in stock and custom applicationsAll sets include nipples and spoke...

Drag Specialties - DS380139 - Spoke Set - Front - Chrome - 8-1/4"FeaturesSpecial spokes and nipples for lacing to OEM-style steel or aluminum hubsAll sets include nipples and spoke wrench for...