Sportster XLH900

Kit includes a 85mm GPS speedometer and a chrome bracket. Speedometer gauge reads 0-120 mph.The chrome bracket mounts to the handlebar riser clamp. Kit includes red generator and blue hi-beam...

Kit includes 85mm GPS electric tachometer and a chrome bracket. Tachometer is 12 volt and operates from a coil impulse.The chrome bracket mounts to the handlebar riser clamp. Kit includes red...

Deco 48mm speedometer kit has a ratio of 2:1, and features a white face with black numbers reading 0-110 mph.Includes gauge, bracket, rubber handlebar clamps, and proper cable which can be installed...

Magneto tachometer kit includes mount bracket to mount to XL handlebar mount.Tachometer is OEM HD, manufactured in Italy. Fits:XL 1957-1970Additional Information

16" x 3.0." rear wheel and brake drum assembly includes an all chrome wheel, brake drum, chrome backing plate and chrome axle kit.Order chrome brake arm separately. ...

16" x 3.00 rear wheel assembly with chrome hub and bearings installed, black rim, and chrome spokes.*NOTE: The valve stem hole is on the sprocket side. **NOTE: All spokes on wheel need to be...

Replica chrome front 19" X 2.5" drop center wheel rim with 40 spoke holes and an 8.5mm center stem valve hole.Rim has original style edge. ...

KH replica chrome front conventional wheel rim.Early conventional KH rim, with a rolled inner seam, not welded. *Note: UPS may consider this part as packaged "oversize" for shipment, as compared to...

18" x 2.15" wheel assembly includes a 40 hole chrome rim, 21 cadmium spokes and a black rear hub, with all internal installed, laced and trued.Accepts a 400-450 x 18" tire. *NOTE: All spokes on wheel...

These rear wheel assemblies start with a 40 hole 18" x 2.5" chrome rim, single flange, 40 stainless spokes and a rear hub.Wheel is laced and trued. Accepts a 130-140 tire size. ...

Rear wheel assembly include a 18" x 2.5" chrome rim, 40 chrome spokes, and a rear hub. Wheel is laced and trued. Accepts a 130-140 tire size.NOTE: All spokes on wheel need to be inspected and...

This rear 18" x 2.15" wheel assembly includes a 40 hole chrome rim, 40 stainless steel spokes and a rear hub with bearings installed, laced and trued. Accepts a 130-140 tire size.NOTE: All spokes on...

Rear wheel assembly includes 18" x 2.15" chrome conventional style rolled rim, 40 chrome spokes and a rear hub. Wheel is laced and trued. Accepts a 100-120 tire size.NOTE: All spokes on wheel need to...

Features a 16" x 3.00" drop center rim with a large valve stem hole, 40 chrome twirled spokes and a hub with bearings installed.NOTE: All spokes on wheel need to be inspected and re-torqued after 500...

These rear wheel assemblies start with a 40 hole 16" x 3" chrome rim, 40 polished stainless steel spokes and a rear hub with bearings installed. Accepts a 130-140 tire size.NOTE: All spokes on wheel...

16" x 3.00 rear wheel assembly with chrome hub and bearings installed, chrome rim, and chrome spokes.*NOTE: The valve stem hole is on the sprocket side. **NOTE: All spokes on wheel need to be...

H-C type 2.15" x 19" alloy rim features a polished natural finish and has 40 spoke holes.Exact as original! Rim is drilled to fit Harley type applications on smaller diameter hubs. CV hole measures...

H-C type 2.15 x 18" alloy wheel rim features a polished natural finish and has 40 spoke holes.Exact as original! Outside measurement flange to flange is 2-7/8", inside diameter at bead pattern area...

200 XL rigid frame features a 40  rake with a 3" stretch in front legs to accept a 1-1/8" belt with 200 series tire.Frame has kickstand tab and battery box mount welded in place. Accepts a right side...

Footpeg support bar set is the splined type featuring a raw steel construction.Attaches to early Sportster frames to mount footpeg stanchions. One end is splined and the other fits over the frame...

Raw steel weld-on hardtail features a raw steel finish.Replaces entire rear section of the frame, for the full rigid look. *NOTE: Must be installed by a certified welder. Fits:XL 1957-1978Additional...

Frame hardtail is bolt on type. Accepts drum style brakes on a rigid frame.Unit should be aligned for chain clearance prior to final bolting. DIY hardtail is easy to install as the alignment is...

Frame hardtail replaces shocks on swingarm frames and is drum brake type. Unit should be aligned for chain clearance prior to final welding.DIY hardtailing is easy to install as the alignment is...

XL brake cross shaft kit includes two bushings. Kit must be welded in place. Fits:XL 1952-1976Additional Information UOM1 - KIT

This raw steel full rear section hardtail for Sportsters includes the rear motor mount and 4 bolt plate mount with upper and lower tube set. Frame is used to replace the stock rear motor mount and...

Frame mount tab set for solo seats have weld on mount tabs. Use with T bar and pivot bolt to mount K and CH solos. Fits:XL 1957-1979Additional Information UOM

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

XL raw brake shaft tube for mechanical brakes. Kit includes machined 7.25" tube with brass bushing and shifter cross bushing set installed. Must be welded in place to frame.*NOTE: Locate tube using...

Bobbed rear fender kit includes a steel fender, cateye tail lamp, chrome tail lamp bracket, and chrome struts.We suggest pre fitting fender prior to painting. Order sissy bar components separately. ...

V-Twin - 50-0625 - XL Rigid Tool Box KitDescriptionLeft side tool box kit is the weld on type for rigid frames on Sportster builds.*NOTE: Weld bracket to lower rigid frame hardtail tube position or...

Magneto advance plate screw set includes four allen flathead screws and 2 hex screws with lock nuts.Kit includes 4 tapered screws for mounting base to magneto head. Fits 1965-70 XL with Magneto cable...

Drag Specialties - DS902016 - Solo Seat Mounting Bracket - XL '57-'78 Features Chromed bracket for Harley® rigid frame XL models 7" on-center spring mounts Not for XLCR models. Specs

Drag Specialties - DS720814 - Fender License Plate Mount - ChromeFeatures4" x 7" mount includes dual rubber gaskets, allowing the angle of the mount to be raised or lowered as neededIncludes all...

Drag Specialties - DS390193 - Gas Cap - Vented - ChromeFeaturesReplacement gas caps for OEM and custom tanksWill not fit screw-in type tanks.Replacement Part for OEM Number(s):6110335Specs

Drag Specialties - DS380201 - Spoke Set - Drop Center - Front/Rear - Stainless Steel - 16"FeaturesStrong, quality spoke sets used in stock and custom applicationsAll sets include nipples and spoke...

Drag Specialties - DS380140 - Spoke Set - Drop Center - Front - Chrome - 21"FeaturesStrong, quality spoke sets used in stock and custom applicationsAll sets include nipples and spoke wrench for...

Drag Specialties - DS380132 - Spoke Set - Drop Center Front - Chrome - 7.75" x 18"FeaturesStrong, quality spoke sets used in stock and custom applicationsAll sets include nipples and spoke wrench for...