Sportster XLCH 900 Kick Start

Female footpeg set for Sportster model driver applications. Constructed of machined female steel yoke finished with zinc plating and fitted with rubber slip on footpeg rubber.Rubber is replaceable...

Early style stock XL kickstand leg with a round end features a zinc finish and is 10-1/2" long. Fits:XL 1952-1979Additional Information UOM1 - EA

Chrome driver footpeg support set is spline type.Use with large female type driver pegs. Fits:XL 1952-1974Additional Information OEM No.50948-71

9-1/2" kickstand features a chrome finish.The pin is installed from the bottom and held in by a set screw, same as OEM. Fits:XL 1952-1979Additional Information

Early style stock XL kickstand leg with a round end features a chrome finish and is 10-1/2" long. Fits:XL 1952-1979Additional Information OEM No.50062-52

Driver footpeg support bar set is the splined type with a zinc finish. Use with large female type driver pegs. Fits:XL 1952-1974Additional Information OEM No.

Kickstand pin kit for stock length kickstand. Fits:XL 1952-1984Additional Information OEM No.50090-53 UOM

XL kickstand mount tab is contructed of raw steel. Mount tab accepts stock extended XL kickstands, available separately. For use with 1" tubing. Fits:XL 1957-1978Additional Information

Chrome passenger footpeg bracket bolts to rear motor mount bolts, for use on rigid or swingarm frames.Uses large female driver footpegs. Order footpegs and return springs separately. Fits:XL...

Center kickstand kit is constructed of cast aluminum and includes spring, and hardware for mounting to stock swingarm frames. Fits:XL 1957-1981K 1952-1956Additional Information

Rear wheel brake rod and cable adjusting nut features a cadmium finish. Fits:XL 1957-1978K 1952-1956KH 1952-1956Additional Information UOM<

Rear wheel brake rod and cable adjusting nut features a chrome finish. Fits:XL 1957-1978K 1952-1956KH 1952-1956Additional Information UOM

Alloy clutch lever with a 7/16" hole. Fits:XL 1957-1970Additional Information UOM1 - EA ManufacturerV

Polished clutch hand lever assembly with 7/16" hole. Fits:XL 1965-1970K 1952-1956Additional Information OEM No.38604-65A

Chrome clutch hand lever assembly with 7/16" hole includes cable pin. Fits:XL 1965-1970 1" barsAdditional Information OEM No.38604-65A

V-Twin - 24-2024 - 41mm Fork Assembly with Chrome Sliders 21 inch WheelDescriptionHard chrome wide glide fork assembly with chrome sliders are assembled with internal components.Includes a 21" chrome...

V-Twin - 24-2023 - 41mm Fork Assembly with Chrome Sliders 21 inch WheelDescriptionHard chrome wide glide fork assembly with chrome sliders are assembled with internal components.Includes a 21" chrome...

Chrome spring fork is 6" longer than stock.Includes axle and top clamp. Stem has a 1" x 24 thread. Axle is ¾" outer diameter. Height is measured from the top of the fork leg (where the triple tree...

Chrome spring fork is 4" longer than stock.Includes axle and top clamp. Stem has a 1" x 24 thread. Axle is ¾" outer diameter. Height is measured from the top of the fork leg (where the triple tree...

Chrome spring fork is 2" longer than stock.Includes axle and top clamp. Stem has a 1" x 24 thread. Axle is ¾" outer diameter. Height is measured from the top of the fork leg (where the triple tree...

Standard chrome spring fork.Includes axle and top clamp. Stem has a 1" x 24 thread. Axle is ¾" outer diameter. Height is measured from the top of the fork leg (where the triple tree fits), to the...

Fork tube cover set for XLCH models with gator fork boots installed.Tube sleeves cover the bare tubes between the upper and lower triple tree. Fits:XL 1959-1972Additional Information <

Xl Fork triple tree assembly includes an upper aluminum triple tree and black forged lower tree.*NOTE: Order neck cup, bearing races and hardware installation separately. Fits:XL 1957-1972 33.4mm...

XL fork tube conversion kit includes all components to convert 1957-1970 Sportster fork legs to "1971" type.NOTE: 1957-1970 lower legs do not have a seal provision. Use the original lowerlegs and...

Lower triple tree is constructed of steel and accepts 33.4mm fork tubes.Lower triple tree is drilled and tapped 5/16 x 24 for covers. Fits:XL 1957-1972Additional Information

Fork assembly wide glide with chrome sliders accept 10" dual disc for 1952-1981 XL models.Fork assembly wide glide with chrome sliders features wide style with triple trees, axle, neck bearings, top...

Wide glide fork assembly with polished sliders accept 11-1/2" single disc for 1952-1981 XL models.Fork assembly wide glide with polished sliders features wide style with triple trees, axle, neck...

Lower race for fork neck cup bearing Fits:XL 1952-1977Additional Information OEM No.48347-52 UOM1 - E

Front brake lever. Fits:FX 1971-1972XL 1964-1972Additional Information OEM No.44307-52 UOM1

XL fork bushing set is a 4 piece set.Outer diameter measures 1.475". Fits:XL 1957-1971K 1952-1954Additional Information UOM1 - SET

Kit includes cups, races, bearings, and covers.Features solid internal fork stops that are built into the cups and hidden away. For stock and custom rigid frames that accept stock XL neck cups...

Dust shield set for XL models. Fits:XL 1952-1977Additional Information UOM1 - SET ManufacturerV-Twin<

Timken fork neck cup tapered bearing set use with race.Includes top and bottom bearing. Order race separately. Fits:XL 1952-1977Additional Information UOM

Kit includes 2 chrome cups, 2 tapered bearings, and dust shields. Kit is for a 7/8" stem.To convert 1952-1977 ball bearing style cups to Timken tapered type. Kit includes two different size bearings,...

Fork triple tree sleeve Fits:XL 1952-1977Additional Information OEM No.45721-54 UOM1 - EA

Kit includes top nut, sleeve and dust cover. Fits:XL 1952-1977Additional Information UOM1 - KIT Manufacturer

Chrome fork neck cup set with races.The area where the cup presses into the frame measures 2.208" outer diameter and 1.965" inner diameter. Order bearings separately. Sold as a pair. Fits:XL...

Kit includes cups, races and ball bearings. Fits:XL 1952-1977Additional Information UOM1 - KIT Manufacturer

Front brake backing plate pivot stud. Fits:FX 1971-1972XL 1964-1972Additional Information OEM No.44156-64

Zinc triple tree upper dust shield Fits:XL 1952-1978Additional Information OEM No.48370-52 UOM1 - EA<