1967

Raw steel weld-on hardtail features a raw steel finish.Replaces entire rear section of the frame, for the full rigid look. *NOTE: Must be installed by a certified welder. Fits:XL 1957-1978Additional...

Replica swingarm frame is our authentic reproduction of FLH style to accept a Panhead or Shovelhead engine, 4-speed transmission, seat post, and accepts a round or square swingarm. All components are...

Replica swingarm frame is an authentic reproduction of FLH style for 1965-1984.Frame accepts Panhead or Shovelhead engine, 4-speed transmission, 12v battery and round swingarm for drum brake...

Raw frame swingarm features forged axle plates for 3/4" axle with round tube construction. Fits:FX 1971-1972FL 1958-1972Additional Information OEM No.

This replica authentic style frame neck web repair section must be welded in after cutting stock or custom frame. It features the right side lock housing.Order new lock assembly, separately. Fits:FL...

Frame hardtail is bolt on type. Accepts drum style brakes on a rigid frame.Unit should be aligned for chain clearance prior to final bolting. DIY hardtail is easy to install as the alignment is...

Frame hardtail replaces shocks on swingarm frames and is drum brake type. Unit should be aligned for chain clearance prior to final welding.DIY hardtailing is easy to install as the alignment is...

Chrome front engine bar features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low...

Engine bar features 1" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very slow speed slide). They...

XL brake cross shaft kit includes two bushings. Kit must be welded in place. Fits:XL 1952-1976Additional Information UOM1 - KIT

Frame top engine mount is two halves with seat tee and rear tank mounts incorporated into the top mount.Weld in place for accurate restoration. ...

Rigid hardtail frame raw steel rear section is 1957 style replica construction with components featuring the factory details of the period.The rear transmission mounts are 2" from the bottom cross...

Replica rear hardtail frame section is duplicated from an original rigid frame of 1957. Left axle plates are forged steel as OE. Weld-on type. The axle slots are 7/8" on both sides.Full replica...

Chrome finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications.Lowers bike 1/2"...

This raw steel full rear section hardtail for Sportsters includes the rear motor mount and 4 bolt plate mount with upper and lower tube set. Frame is used to replace the stock rear motor mount and...

Neck frame with hallmarks forged in place. Machined to accept neck lock tumbler.Milwaukee forged neck is accomplished in 4 stages: First the steel is fired as red hot ingot, next huge hammers compact...

Lower frame gas tank mount set is without cross bracket. It includes the right and left tabs. Tabs are constructed of st eel and have a raw finish.May require finishing prior top installation and...

This 5th Mount transmission frame repair tab is weld on style for stock frames. The tab is constructed of steel and has a raw finish.May require finishing prior to installing. Fits:FX 1971-1984FL...

Rear pipe frame tab. Fits: FL 1958-1984 Additional Information UOM 1 - EA Manufacturer V-Twin

Brake line tee tab. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA Manufacturer

Cable mount frame tab is for under tank. Fits:FL 1955-1972Additional Information UOM1 - EA Manufacturer

Upper shock frame mounts are weld on style for stock frames.Sold as a set of two. Fits:FL 1965-1984FX 1971-1984Additional Information UOM1

Casting top seat mount is for frame seat post, frame back bone and frame upper seat rail yoke. Fits:FL 1958-1984Additional Information UOM1 - EA

Frame mount tab set for solo seats have weld on mount tabs. Use with T bar and pivot bolt to mount K and CH solos. Fits:XL 1957-1979Additional Information UOM

This weld on style coil mount frame block set repairs stock frames and has a 3/8"-24 UNF thread. Fits:FL 1956-1983FX 1971-1983Additional Information UOM<

Frame top engine mount is two halves with seat tee and rear tank mounts incorporated into the top mount. Weld in place for accurate restoration.*NOTE: Threaded for seat "T" bolt. Fits:FL...

Rigid frame front oil tank mount casting to be welded on.Thread is 5/16 x 24 and the lip from the bottom to the top measures 1-1/4". For use with 1-1/2" bar. Fits:FL 1941-1984FX 1972-1984EL...

Rear frame engine mount and front transmission mount. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA

Neck frame forging has a 30  rake with key hole. Machined to accept neck lock tumbler.Forged neck is accomplished in 4 stages: First the steel is fired as red hot ingot, next huge hammers compact and...

Rear tank frame mount tabs. Fits:FL 1941-1984EL 1936-1947U 1937-1948Additional Information UOM1 - SET

New Old Stock" Frame gusset plate is for the left side on swingarm frames.New Old Stock from the 1980's, part has rust and oxidation! Fits:FL 1958-1968FLH 1958-1968Additional Information

Weld on frame footpeg mount without thread.Mount can be welded to 1958-1977 swingarm frames to utilize the stock FXE mount and raise the peg position. Sold as a pair. Fits:FX 1971-1978FL...

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

Raw steel neck lock pin only. Fits:FL 1948-1968VL 1930-1936Additional Information UOM1 - EA Manufactu

Replica rear hardtail frame section is duplicated from an original rigid frame. Weld-on type and does not have seat post bushing.The rear transmission mounts are 1-1/2" tall. This hardtail includes...

XL raw brake shaft tube for mechanical brakes. Kit includes machined 7.25" tube with brass bushing and shifter cross bushing set installed. Must be welded in place to frame.*NOTE: Locate tube using...

Steering lock assembly kit includes complete key assembly, key lock, two keys, spring, pin, plunger, frame plug, and neck casting piece for lock. Must be welded in place.Steering lock assembly kit...

Beaded windshield is a fixed mount type which comes completely assembled.Includes beaded windshield top and an adjustable lower windshield to fit FL aluminum headlamp cowl assembly. The center bolt...

Top beaded windshield is short style. Fits:FLH 1949-1984Additional Information OEM No.58020-49A UOM1

Frame saver mounting kit for gas tanks must be welded to Big Twin stock or custom frames. Casting features provision for damper pin, as required on 1949-1984 Big Twins.*Note: Includes speedometer...