1978

V-Twin - 51-1955 - Replica inchHM inch Straight Leg Rigid FrameDescriptionReplica "HM" straight leg rigid frame is an authentic reproduction of the 1954-1957 straight leg frame with stock 30  neck...

Engine mount shim is used to raise motor for front or rear clearance, when necessary.Sold in a pack of 5. Fits:FL 1941-1999EL 1936-1952Additional Information

Engine bar features 1" tubing and a black finish.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very slow...

V-Twin - 51-1322 - Lowered Rear Axle Plate Set RawDescriptionLowered rear axle plates are threaded 3/8"-18 for fender brace sissy bar mounting. Adjusters threaded 3/8"-24 use screws for adjusters, to...

Raw steel weld-on hardtail features a raw steel finish.Replaces entire rear section of the frame, for the full rigid look. *NOTE: Must be installed by a certified welder. Fits:XL 1957-1978Additional...

Replica swingarm frame is our authentic reproduction of FLH style to accept a Panhead or Shovelhead engine, 4-speed transmission, seat post, and accepts a round or square swingarm. All components are...

Replica swingarm frame is an authentic reproduction of FLH style for 1965-1984.Frame accepts Panhead or Shovelhead engine, 4-speed transmission, 12v battery and round swingarm for drum brake...

Frame hardtail is weld on type and includes weld on frame plate. Accepts drum type brake.Hardtail should be aligned for chain clearance prior to final welding. This hardtail fits hardtail rigid...

This replica authentic style frame neck web repair section must be welded in after cutting stock or custom frame. It features the right side lock housing.Order new lock assembly, separately. Fits:FL...

Frame hardtail is bolt on type. Accepts drum style brakes on a rigid frame.Unit should be aligned for chain clearance prior to final bolting. DIY hardtail is easy to install as the alignment is...

Rear frame swingarm is chrome and is for 4-speed rear chain drive models. Bearings and races are not included.Measures 12.5" from center of shock bolt to center of swingarm pin and 12.50" from the...

Engine bar set features left and right sides.Two piece set. **WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while...

Chrome front engine bar features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low...

Rear frame swingarm is black and is for 4-speed rear chain drive models. Bearings and races are not included.Measures 12.250" from center of shock bolt to center of swingarm pin and 12.50" from the...

Engine bar features 1" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very slow speed slide). They...

Engine bar features 1-1/4" tubing.This engine bar is not for use with extended forward controls. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection...

Rigid hardtail frame raw steel rear section is 1957 style replica construction with components featuring the factory details of the period.The rear transmission mounts are 2" from the bottom cross...

Raw finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications. Swingarm is for use...

Replica rear hardtail frame section is duplicated from an original rigid frame of 1957. Left axle plates are forged steel as OE. Weld-on type. The axle slots are 7/8" on both sides.Full replica...

Chrome finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications.Lowers bike 1/2"...

This raw steel full rear section hardtail for Sportsters includes the rear motor mount and 4 bolt plate mount with upper and lower tube set. Frame is used to replace the stock rear motor mount and...

Lower frame gas tank mount set is without cross bracket. It includes the right and left tabs. Tabs are constructed of st eel and have a raw finish.May require finishing prior top installation and...

This 5th Mount transmission frame repair tab is weld on style for stock frames. The tab is constructed of steel and has a raw finish.May require finishing prior to installing. Fits:FX 1971-1984FL...

Rear pipe frame tab. Fits: FL 1958-1984 Additional Information UOM 1 - EA Manufacturer V-Twin

Brake line tee tab. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA Manufacturer

Upper shock frame mounts are weld on style for stock frames.Sold as a set of two. Fits:FL 1965-1984FX 1971-1984Additional Information UOM1

Casting top seat mount is for frame seat post, frame back bone and frame upper seat rail yoke. Fits:FL 1958-1984Additional Information UOM1 - EA

Frame mount tab set for solo seats have weld on mount tabs. Use with T bar and pivot bolt to mount K and CH solos. Fits:XL 1957-1979Additional Information UOM

This weld on style coil mount frame block set repairs stock frames and has a 3/8"-24 UNF thread. Fits:FL 1956-1983FX 1971-1983Additional Information UOM<

Rigid frame front oil tank mount casting to be welded on.Thread is 5/16 x 24 and the lip from the bottom to the top measures 1-1/4". For use with 1-1/2" bar. Fits:FL 1941-1984FX 1972-1984EL...

Rear frame engine mount and front transmission mount. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA

Neck frame casting fits XL models to be welded in place on 30  stock or custom frames. Has unmachined padlock boss. Accepts neck cup kit.Neck frame accepts stock bearing cups and trees. Fits:XL...

Rear tank frame mount tabs. Fits:FL 1941-1984EL 1936-1947U 1937-1948Additional Information UOM1 - SET

Weld on frame footpeg mount without thread.Mount can be welded to 1958-1977 swingarm frames to utilize the stock FXE mount and raise the peg position. Sold as a pair. Fits:FX 1971-1978FL...

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

Replica rear hardtail frame section is duplicated from an original rigid frame. Weld-on type and does not have seat post bushing.The rear transmission mounts are 1-1/2" tall. This hardtail includes...

XL raw brake shaft tube for mechanical brakes. Kit includes machined 7.25" tube with brass bushing and shifter cross bushing set installed. Must be welded in place to frame.*NOTE: Locate tube using...

Beaded windshield is a fixed mount type which comes completely assembled.Includes beaded windshield top and an adjustable lower windshield to fit FL aluminum headlamp cowl assembly. The center bolt...

Top beaded windshield measure 18" and is for use on fiberglass fairings only.Fits 1969-1984 FLH 4 speed and 1980-1985 FLT 5 speed models with Batwing fairings. Fits:FLT 1980-1985FLH...

Top beaded windshield is short style. Fits:FLH 1949-1984Additional Information OEM No.58020-49A UOM1