1983

Description 19" WR/KR/XR rear wheel features a natural finish hub with 9/16" ball bearings and internals installed. Laced with 6-8 gauge stainless steel spokes to a black finish 19" x 3.0" 40 hole...

Replacement tank mounts can be used on Fat Bob tanks and also on custom frames where the mounts do not exist. Fits:FL 1955-1984Additional Information UOM

200 XL rigid frame features a 40  rake with a 3" stretch in front legs to accept a 1-1/8" belt with 200 series tire.Frame has kickstand tab and battery box mount welded in place. Accepts a right side...

Rear frame swingarm features a chrome finish. Bearings and races are not included. Fits:FX 1970-1984Additional Information UOM1 - EA

V-Twin - 51-1955 - Replica inchHM inch Straight Leg Rigid FrameDescriptionReplica "HM" straight leg rigid frame is an authentic reproduction of the 1954-1957 straight leg frame with stock 30  neck...

Engine mount shim is used to raise motor for front or rear clearance, when necessary.Sold in a pack of 5. Fits:FL 1941-1999EL 1936-1952Additional Information

V-Twin - 51-1322 - Lowered Rear Axle Plate Set RawDescriptionLowered rear axle plates are threaded 3/8"-18 for fender brace sissy bar mounting. Adjusters threaded 3/8"-24 use screws for adjusters, to...

Replica swingarm frame is our authentic reproduction of FLH style to accept a Panhead or Shovelhead engine, 4-speed transmission, seat post, and accepts a round or square swingarm. All components are...

Replica swingarm frame is an authentic reproduction of FLH style for 1965-1984.Frame accepts Panhead or Shovelhead engine, 4-speed transmission, 12v battery and round swingarm for drum brake...

Chrome left and right pivot mount end caps with footpeg mount holes.The OEM number for the right end cap is 50589-93, and the OEM number for the left end cap is 50588-93. Fits:FLT 1982-1984FLT...

This replica authentic style frame neck web repair section must be welded in after cutting stock or custom frame. It features the right side lock housing.Order new lock assembly, separately. Fits:FL...

Engine bar set features left and right sides.Two piece set. **WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while...

Engine bar features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide)...

Engine bar features 1-1/4" tubing.This engine bar is not for use with extended forward controls. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection...

Passenger footboard set with swingarm mount kit includes streamline style mini footboards.A Wyatt Gatling patch is included in the kit. Installation will require re-installation of the original...

Chrome swingarm mount kit includes right & left side chrome pivot caps, passenger footboard mounts and passenger footboard with rubber pads.Installation will require re-installation of the original...

Rigid hardtail frame raw steel rear section is 1957 style replica construction with components featuring the factory details of the period.The rear transmission mounts are 2" from the bottom cross...

Raw finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications. Swingarm is for use...

Replica rear hardtail frame section is duplicated from an original rigid frame of 1957. Left axle plates are forged steel as OE. Weld-on type. The axle slots are 7/8" on both sides.Full replica...

Chrome finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications.Lowers bike 1/2"...

Lower frame gas tank mount set is without cross bracket. It includes the right and left tabs. Tabs are constructed of st eel and have a raw finish.May require finishing prior top installation and...

This 5th Mount transmission frame repair tab is weld on style for stock frames. The tab is constructed of steel and has a raw finish.May require finishing prior to installing. Fits:FX 1971-1984FL...

Rear pipe frame tab. Fits: FL 1958-1984 Additional Information UOM 1 - EA Manufacturer V-Twin

Brake line tee tab. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA Manufacturer

Upper shock frame mounts are weld on style for stock frames.Sold as a set of two. Fits:FL 1965-1984FX 1971-1984Additional Information UOM1

Casting top seat mount is for frame seat post, frame back bone and frame upper seat rail yoke. Fits:FL 1958-1984Additional Information UOM1 - EA

This weld on style coil mount frame block set repairs stock frames and has a 3/8"-24 UNF thread. Fits:FL 1956-1983FX 1971-1983Additional Information UOM<

Rigid frame front oil tank mount casting to be welded on.Thread is 5/16 x 24 and the lip from the bottom to the top measures 1-1/4". For use with 1-1/2" bar. Fits:FL 1941-1984FX 1972-1984EL...

Rear frame engine mount and front transmission mount. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA

Rear tank frame mount tabs. Fits:FL 1941-1984EL 1936-1947U 1937-1948Additional Information UOM1 - SET

Weld on frame footpeg mount without thread.Mount can be welded to 1958-1977 swingarm frames to utilize the stock FXE mount and raise the peg position. Sold as a pair. Fits:FX 1971-1978FL...

Mid control mount kit is used to mount to the two holes located in the lower frame brace. Kit features a black finish.Mount features holes on each side for the left and right foot brake peg mount...

XL control mount set features a black finish. Control mounts for right (2 bolt plate) and left (3 bolt plate) to accept Big Twin forward controls.Set is used to mount 1941-1999 Big Twin forward mount...

V-Twin - 51-0484 - XL Hardtail Axle Plate SetDescriptionRaw set of right and left axle plates for Sportster hardtails, features 7/8" slots on both sides. Fits:XL 1982-UPAdditional Information<

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

XL rear motor mount pad is the tall type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA

XL rear motor mount pad is the short type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA

Replica rear hardtail frame section is duplicated from an original rigid frame. Weld-on type and does not have seat post bushing.The rear transmission mounts are 1-1/2" tall. This hardtail includes...

FXR weld on top motor mount features a raw finish and is . for use on frame.Must be welded in place on FXRT and FLT models. Fits:FXR 1982-1990FLT 1980-1990Additional Information <

Beaded windshield is a fixed mount type which comes completely assembled.Includes beaded windshield top and an adjustable lower windshield to fit FL aluminum headlamp cowl assembly. The center bolt...