2004

Jims - 5530 Remote Fuel Tank fits H-D Models w/ Delphi Fuel Injection (Except V-Rod) Features: Tank is completely mobile, even when pressurized; canister does not need to be continuously connected to the air supply Small enough to hang from a...

Jims - 1147 Alternator Rotor Puller fits '97-'06 Big Twin Models Features: A must-have tool for 45A charging systems; will also work on any Harley-Davidson® alternator system that has threaded puller holes Tool protects threads on sprocket shaft...

Jims - 2244 3/8" 35 mm Fork Nut Socket fits For Big Twin & Sportster Models Features: Used to remove and install top fork nuts on fork tubes Rubber protector inside socket Will clear most handlebars Made in the U.S.A...

Jims - 2240 Head Holder Guide Tool '48-'04 Big Twin, '57-'03 Sportster & Some SE CVO Twin Cam Models (5/16” Valve Guides) Features: Adapters are supported by a stand that makes it easy to press valve guides in and out A special guide...

Jims - 1146 Crankshaft Bearing Installer fits '00-'17 Twin Cam “B” Motors Models Features: Designed to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearing Made in the U.S.A...

Jims - 1162 Caliper Piston Remover fits '00-'07 Big Twin & '00-'03 Sportster 4-Piston Front/​Rear Calipers Models Features: Prevents damage to pistons and cylinders when installing new seals and wipers Holds pistons square in their cylinder...

Jims - 1167 Balancer Shaft/Removal Bearing Tool fits '00-'06 Twin Cam “B” Motors Models Features: Installing portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's bore Pulls the...

FLHRS Jims - 2043 41mm Fork Nut Socket fits '48-'17 Wide Glide Models Features: Eliminates possible burring of plug caused by wrenches Used to remove and install top fork-tube plug Fits 41 mm forks Made in the U.S.A...

Jims - 1705 Exhaust Drill Plate fits '84-'17 Big Twin (Except M-Eight), '86-'22 Sportster & '94-'09 Buell Models (Except 1125R) Features: Will position the seal evenly into the exhaust port of head Tool can be used with exhaust flange nuts Made...

Jims - 1034 Sprocket Shaft Holder fits '55-'99 Big Twin & '99-'06 Twin Cam (Except '06 Dyna) Features: Used to hold flywheel assembly in vise, with or without left case attached Made in the U.S.A...

Jims - 95760-57 Bushing Bearing Puller fits '66-'17 Big Twin (Except M-Eight), '57-'22 Sportster & Buell Models (Except 1125R) Features: Used to remove rocker bushing or bearing in one easy operation Made in the U.S.A...

Jims - 33443-84 Tappet Aligning Tool fits 'L76-'17 Big Twin Models (Except M-Eight) Features: Can also be used to align rocker box bases on Evolution head (requires two tools) Also used in Harley-Davidson® Twin Cam oil pump alignment...

Jims - 2260 Sprocket Lock Tool fits '99-'17 Twin Cam & '80-'99 Big Twin Models w/ Rear Belt Drive Features: Lock the transmission pulley for removing or installing pulley nut Made in the U.S.A...

Jims - 2189 Transmission Shaft Installer fits '83-'06 Big Twin Models Features: Installs transmission shaft without the use of a hydraulic or arbor press Made in the U.S.A. Fitment 2008 Harley-Davidson Fat Bob...

Jims - 1288 Crankshaft Guide fits '99-'17 Twin Cam & '03-'09 Buell XB9R/X B9S Models Features: Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A...

Jims - 1725 Head Bearing Race Installer fits '36-'17 Big Twin Models w/ Stock or Custom Frames (Except '14-'17 Dresser) Features: Use to install steering head races, stock and custom, as well as install cups in the frame This tool pulls the races...

Jims - 2283 Transmission Door Puller fits '80-'06 Big Twin 5-Speed Models Features: Removes transmission door with gears and shaft attached Made in the USA Puller will not damage door bearings. Fitment 2006 Harley-Davidson Street...

Jims - 1720 Main Bearing Remover fits '80-'06 Big Twin 5-Speed Transmissions Models Features: Removes old bearing straight and will not damage the transmission case Can be used without removing transmission from the bike Made in the U.S.A...

Jims - 2256 Drive Gear Seal Installation fits All 5-Speed Big Twin Models Features: Use to install main drive gear oil seal to the proper depth with transmission assembled Includes protective sleeve for seal, which can be used to protect main drive...

Jims - 2234 Primary Drive Lock Tool fits '70-'06 Big Twin & '86-'22 Sportster Models Features: Use on all primaries between front primary chain and motor sprocket Made in the U.S.A. Fitment 2016-2017 Harley-Davidson 1200 Roadster...

Jims - 39361-69 Sprocket Shaft Seal Installation Tool fits '69-'10 Big Twin & Twin Cam Models Features: Designed to press oil seal over sprocket shaft into case Made in the U.S.A. Fitment 2010 Harley-Davidson Street Glide Trike...

Jims - 35316-80 5-Speed Main Drive Gear Tool fits '80-'06 Big Twin (Except '06 Dyna) & '91-'06 Sportster Models Features: Installs the main drive gear without removing the transmission Used to remove and install the main drive gear Made in the...

Jims - 34902-84 Mainshaft Bearing Race Tool fits 'L84-'20 Big Twin Models Features: Used to remove and install the inner bearing race on the transmission mainshaft Made in the U.S.A. Fitment 2016-2017 Harley-Davidson Fat Boy S...

Jims - 95970-32C Piston Pin Bush Tool fits '36-'99 Big Twin, '57-'20 Sportster & Buell Models (Except 1125R) Features: Use to remove and install wrist pin bushings without removing rods from crankcase Made in the U.S.A...

Jims - 1280 Camshaft Bearing Puller fits '99-'06 Twin Cam (Except '06 Dyna) for Removal of Bearings, 'L00-'06 FXST/FL & 'L00-'05 FXD for Removal of Front Cam Bearing Features: Once the camshafts are removed from the support plate this tool will...

Jims - 955 Gauge for Harley-Davidson Injection Pressure fits '01-'20 Big Twin Models w/ Delphi EFI (Except '18-'20 Softails) Features: Includes all necessary parts to diagnose Delphi fuel injection; a large gauge assembly, 8" hose, 2" hose, fuel tank...

Jims - 970 3rd Hand Axle Locker Tool fits '02-'21 FLT/​FLHT Models Features: Eliminates the need for a helper or trying to blindly hold the axle from the other side of the tire Prevents axle from moving while torquing down the axle nut after setting...

Jims - 977 Fork Stem Nut Wrench fits '96-'13 FLHT & '94-'13 FLHR Models Features: This tool allows the ability to loosen, tighten and torque to spec the 1-1/2” stem nut without radio removal Normally to get access to the top stem nut...

Jims - 5822 Swing Arm Bearing Installer fits '02-'21 Touring Models Features: Both drive side and brake side bearings, which are at different depths, can be easily and accurately installed with this tool kit JIMS® took it one step further and...

Jims - 2232 Bearing Race Tool fits '84-'17 Big Twin (Except '14-'17 Dressers), '86-'22 Sportster & '94-'02 Buell OEM Frames (Will Also Work on Most Aftermarket Frames) Features: Removes and installs steering head bearing race on 84-16 Big Twin...

Jims - 96600-36B Valve Spring Compressor Tool fits '36-'04 Big Twin & '57-'03 Sportster Models Features: Comes with new valve collar receiver for safer tool usage, and can be clamped in vice Hardened ball bearing style tip at valve head end...

Jims - 34731-84 Valve Guide Installer fits all Evolution & '99-'04 Twin Cam Models (OEM #34731-84) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A...

Jims - 1017-37TB Cam Bushing Installer fits '37-'48 Big Twin Side-Valve Motors, '54-'20 Sportster, '91-'09 Buell Models (Except 1125R) Features: Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit...

Jims - 94660-37A Counter Shaft Sprocket Locknut Wrench fits '36-'06 Big Twin Models (Except '06 Dyna) Features: Removes hex nut from end of main drive gear that secures the rear drive transmission pulley Extra-long two-piece design Made in the...

Jims - 1051 Wrist Pin Bushing Tool fits '99-'06 Twin Cam Models Features: Used to remove and install wrist pin bushings without removing connecting rods from crankcases Comes with instructions Made in the U.S.A...

Jims - 1283 Camshaft Chain Tensioner Tool fits '99-'06 Twin Cam Models (Except '06 Dyna) Features: Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams Also checks spring loads on chain...

LA Choppers - Pinned Hefty Top Clamp fits '99-'23 Big Twin Models w/ 3-1/2 ” on Center Risers & Offset Mounting Holes Features: Fits Hefty handlebars and risers Polished aluminum construction Pinned to prevent movement of handlebars Made...

Forbidden Motorcycles - Moto Style Handlebars 1" (1-1/8" Clamping Area) The Forbidden Motorcycles 1" Moto Style Bars feature a 1-1/8" clamping area but taper down to 1" to accommodate stock Harley hand controls, eliminating the need to sleeve them. They...

Custom Cycle Engineering - Steering Damper System fits '99-'07 FLHR/​FLHT/​FLHTCU/​FLHX Models Features: This complete steering damper system stabilizes the front fork and helps prevent front-end wobble Custom-designed 1-1/4" clamp and bracket...

Custom Cycle Engineering - 41 mm Wide Glide Tweek Bar - Chrome Features: Original Randy Smith design As in the good old days with extended front tubes, the need for a tweek bar is here again Vast improvement over the tweek bars used in the 60s and...