Jims - 2268 Main Case Seal Installer Tool fits '85-'06 5-Speed Big Twin & Aftermarket 6-Speeds Models Features: Ensures correct alignment, seal protection and depth when installing the seal Made in the...

Jims - 5502 Ultimate Clutch Adjusting Tool fits '85-'20 Big Twins Models w/ Mechanical Clutch Features: Allows the quick and accurate tightening of the clutch adjusting screw jam nut without having the screw change position No more guessing or...

Jims - 5517 Removal/Installation Shifter Mechanism Sleeve Tool fits '06 Dyna & '07-'20 Big Twin w/ 6-Speed Cruise Drive Transmission Features: A real time saver for removing and installing the shifter mechanism sleeve in cruise drive Big Twin...

Jims - 5534 Compensator Bolt Driver Torx Socket fits '14-'21 Big Twin Models Features: Correct-style driver/socket for the compensating sprocket retaining fastener Made in the USA For use with Jim's part# 10500031 compensator bolt...

Jims - Cruise Drive Countershaft 1st Scissor Gear Alignment Tool fits '17-'20 M-Eight Models Features: Essential for installing countershaft 1st scissor gear in cruise drive transmissions Ensures scissor gear teeth mesh correctly with the mainshaft...

Jims - 988 Valve Spring Compressor fits '05-'17 Twin Cam (Except SE Models), '04-'22 Sportster (Except RH Sportster) & Buell Models (Except 1125R) Features: Used to remove and replace valve and new-style conical valve spring Requires use of JIMS...

Jims - 967 Inner Primary Bearing and Seal Remover/Installer Tool fits 'L84-'06 FXST/​FLST & '85-'06 Touring & Dyna Models Features: Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer...

Jims - 972 6-Speed Main Drive Gear Seal Installer fits all '07-'20 Big Twin & '06 Dyna Models Features: Use to install main drive gear oil seal to the proper depth with transmission assembled Includes protective sleeve for seal, which can be...

Jims - 976 Engine Rotator Tool fits '55-'06 Big Twin Models (Except '06 Dyna Glide) Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 937 7mm Valve Guide Remover fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125R) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made...

Jims - 938 7mm Valve Guide Installer fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125CR) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve...

Jims - 1042-7 Expander Dowel Tool fits All '00-'17 Twin Cam, '00-'22 Sportster & '02-'17 V-Rod Models Features: Removes and installs 3/4", 1", and 25 mm wheel bearings with or without (Anti-Lock Brake System) ABS Made in the U.S.A.

Jims - 5532 Vacuum Tappet fits '84-'20 Big Twin Models w/ Hydraulic Tappet Assemblies Features: Removes the risk of using the starting system to pump up the lifters or damage to the valve train at low rpm if the lifters are not fully bled Special...

Jims - 5808 Valve Spring Compression Collar Tool fits '17-'21 M-Eight Models Features: Valve spring collar allows existing compressor to remove smaller valves on M8 engines For use with JIMS® Valve Spring Compressor Tool (PART# DS-196013) Made...

Jims - 5809 Cylinder Hold Down Tool fits '17-'20 M-Eight & '99-'17 Twin Cam Models Features: Useful when installing the second cylinder over the piston and rings after the first cylinder has been installed One end fits Twin Cam models, while the...

Jims - 5828 Cylinder Head Holder Tool fits '17-'22 M-Eight & All Twin Cam Models Features: Allows you to easily position head for all types of work Use to hold head in vice through spark plug hole For use with Milwaukee Eight engine series Has...

Jims - 5829 Cylinder Torque Plates fits '17-'20 M-Eight 107”, 114” Models Features: Torque plates must be used when boring or honing late-model aluminum cylinders Simulate running stress conditions Come with instructions Made in the U...

Jims - 5834 Engine Stand fits '18-'21 M-Eight Softail Models Features: For use on the Milwaukee Eight™ engine series JIMS Milwaukee-Eight® Softail® engine stand is designed to work on all Milwaukee-Eight® Softail engines JIMS...

Jims - 5832 Ball Bearing Remover Tool fits '17-'20 Softail & Touring Models Features: Easily remove the balancer bearings in both Touring and Softail models without damage to the crankcase Fitment 2020-2021 Harley-Davidson Road...

Jims - 5833 Ball Bearing Installation Tool fits '17-'20 Softail & Touring Models Features: All Milwaukee-Eight® (M8) engines incorporate balancers to reduce vibration Designed to precisely install these bearings in the proper location for...

Jims - 5835 Valve Spring Compressor Tool fits '17-'21 M-Eight Models Features: Once the cylinder is filled with compressed air, the technician can easily rotate the tool and compress the top collar of the valve spring exposing the keepers to remove...

Jims - 5838 Oil Pump Alignment Tool fits '17-'21 M-Eight Engines Models Features: This tool was designed to help the technician assemble the complete cam chest correctly, in a quick and efficient manner The perfect aid for the technician to either...

Jims - 991 Case Splitting Tool fits '18-'21 M8 Softail & Touring Models Features: In order to perform any type of lower end service or performance work, it is necessary to split the crankcase into halves Simply install the tool on the primary...

Jims - 5506 Magnetic Tappet Holder fits all Twin Cam & M-Eight Models Features: Never turn the engine over if the tappet will not spin with your fingers after adjustments were made It is very important that the engine is not rotated while...

Jims - 730 Piston Tester Jet fits '18-'21 M-Eight Softail Models Features: Assists engine rebuilder to clear jet of all assembly lubes; verifies psi number the jet switches to "on" and visualizes spray pattern before cases are sealed Helps determine...

Jims - 1664 5-Speed Transmission Shifter Shaft Sleeve Tool fits '80-'83 FLT/​FLHT/​FXR, '84-'99 Big Twins & '84-'00 FLHT/​FXR/​FXD Models Features: Can be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drum Use...

Jims - 5820 Standard Rear Axle Installation Guide Tool fits '08-'21 Big Twin w/ Hollow 1” (25 mm) Features: Aligns wheel with swingarm, caliper brackets, wheel hubs and spacers Made in the USA For Big Twin models with hollow 1" (25 mm)...

Jims - 2244 3/8" 35 mm Fork Nut Socket fits For Big Twin & Sportster Models Features: Used to remove and install top fork nuts on fork tubes Rubber protector inside socket Will clear most handlebars Made in the U.S.A...

Jims - 2240 Head Holder Guide Tool '48-'04 Big Twin, '57-'03 Sportster & Some SE CVO Twin Cam Models (5/16” Valve Guides) Features: Adapters are supported by a stand that makes it easy to press valve guides in and out A special guide...

Jims - 1110 0.105" Camshaft Pinon Gauge Pins fits '54-'89 Big Twin Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 1989 Harley-Davidson Electra Glide Ultra...

Jims - 1111 0.108" Camshaft Pinion Gauge Pins fits '90-'99 Big Twin Evolution Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...

Jims - 1705 Exhaust Drill Plate fits '84-'17 Big Twin (Except M-Eight), '86-'22 Sportster & '94-'09 Buell Models (Except 1125R) Features: Will position the seal evenly into the exhaust port of head Tool can be used with exhaust flange nuts Made...

Jims - 1034 Sprocket Shaft Holder fits '55-'99 Big Twin & '99-'06 Twin Cam (Except '06 Dyna) Features: Used to hold flywheel assembly in vise, with or without left case attached Made in the U.S.A...

Jims - 95760-57 Bushing Bearing Puller fits '66-'17 Big Twin (Except M-Eight), '57-'22 Sportster & Buell Models (Except 1125R) Features: Used to remove rocker bushing or bearing in one easy operation Made in the U.S.A...

Jims - 38515-90 Clutch Spring Compressor fits '90-'97 Big Twin & '91-'03 Sportster Models Features: For '91-'03 XL applications, compressor nut must be used in conjunction with compressor tool Used to release clutch spring so retainer ring can...

Jims - 1710 Outer Race Snap Ring fits '69-'02 Big Twin Models Features: Used for removing and installing the Timken® bearing outer race snap ring A must for replacing rings in OEM and aftermarket cases Made in the U.S.A...

Jims - 33443-84 Tappet Aligning Tool fits 'L76-'17 Big Twin Models (Except M-Eight) Features: Can also be used to align rocker box bases on Evolution head (requires two tools) Also used in Harley-Davidson® Twin Cam oil pump alignment...

Jims - 1745 Bearing Simulator fits '70-'02 Big Twin Models Features: Designed to allow quick and easy removal and replacement of flywheel assembly in the left-side crankcase when checking rod-to-case, piston-to-flywheel or cylinder-to-flywheel...

Jims - 2260 Sprocket Lock Tool fits '99-'17 Twin Cam & '80-'99 Big Twin Models w/ Rear Belt Drive Features: Lock the transmission pulley for removing or installing pulley nut Made in the U.S.A...

Jims - 2189 Transmission Shaft Installer fits '83-'06 Big Twin Models Features: Installs transmission shaft without the use of a hydraulic or arbor press Made in the U.S.A. Fitment 2008 Harley-Davidson Fat Bob...