Harley Davidson

Frame hardtail is weld on type and includes weld on frame plate. Accepts drum type brake.Hardtail should be aligned for chain clearance prior to final welding. This hardtail fits hardtail rigid...

Chrome frame swingarm.Order pivot kit separately. The width of the inner diameter where the axle goes measures 9-7/8". From the cente rof the axle hole to the rear measures 14-1/2". *NOTE: May have...

Chrome swingarm for Softail models.Swingarm includes spherical bearings installed. Not for use on 2006-2007 FXST and 2007-up FLSTF. ...

Raw frame swingarm features forged axle plates for 3/4" axle with round tube construction. Fits:FX 1971-1972FL 1958-1972Additional Information OEM No.

This replica authentic style frame neck web repair section must be welded in after cutting stock or custom frame. It features the right side lock housing.Order new lock assembly, separately. Fits:FL...

V-Twin - 51-0939 - Chrome Front Engine BarDescriptionEngine bar features 1-1/4" tubing.Will not fit with front spoilers. *NOTE: Does not fit the following models: 2016-UP XL 1200X, 2018-UP XL 1200XS...

Engine bar set features left and right sides with 1-1/4" tubing. For use with stock type saddle bag supports.2004-08 FLTR, FLHX, FLHRS models requires the seperate purchase of OEM #90781-93 Lower...

Rear frame set bar features left and right sides with 7/8" tubing.The stock shape reflectors are not included. *NOTE: Not for use with saddlebag rails. **WARNING: This frame bar may provide limited...

Frame hardtail is bolt on type. Accepts drum style brakes on a rigid frame.Unit should be aligned for chain clearance prior to final bolting. DIY hardtail is easy to install as the alignment is...

Frame hardtail replaces shocks on swingarm frames and is drum brake type. Unit should be aligned for chain clearance prior to final welding.DIY hardtailing is easy to install as the alignment is...

Rear frame swingarm is chrome and is for 4-speed rear chain drive models. Bearings and races are not included.Measures 12.5" from center of shock bolt to center of swingarm pin and 12.50" from the...

Engine bar set features left and right sides.Two piece set. **WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while...

Engine bar features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide)...

Chrome front engine bar features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low...

Rear frame swingarm is black and is for 4-speed rear chain drive models. Bearings and races are not included.Measures 12.250" from center of shock bolt to center of swingarm pin and 12.50" from the...

Engine bar features 1-1/4" tubing.Includes bolts. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low...

Engine bar features 1" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very slow speed slide). They...

Engine bar features 1-1/4" tubing.This engine bar is not for use with extended forward controls. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection...

Engine bar features 1-1/4" tubing and foot rests with rubber pads. Hardware is not included. This will not work with forward controls.**WARNING: This engine/frame bar may provide limited leg and...

Engine bar features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide)...

Engine bar features 1-1/4" tubing.Not for use with forward controls. WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection...

Engine bar features 1-1/4" tubing, and 3 point mounting.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped,...

Engine bar features 1-1/4" tubing and single top mount hole.Includes U-bolts, nuts, and straight bolt. The width between bottom mount plates measures 12" outside to outside. The height from the top...

Bar complements the traditional Touring style and features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over...

Chrome frame guard set includes left and right side with 7/8" tubing.*NOTE: Mounting hardware is not included, must be supplied by the installer. WARNING: This engine/frame bar may provide limited...

XL brake cross shaft kit includes two bushings. Kit must be welded in place. Fits:XL 1952-1976Additional Information UOM1 - KIT

Frame top engine mount is two halves with seat tee and rear tank mounts incorporated into the top mount.Weld in place for accurate restoration. ...

Engine bar features 1-1/4" tubing with rubber pads on foot rests and features a black gloss finish.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique...

Black engine bar features integrated rubber pads for foot rests.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while...

Engine bar features a gloss black finish and integrated rubber pads for foot rests.Hardware is not included. The engine bar has a diameter of 1-5/16". **WARNING: This engine/frame bar may provide...

Passenger footboard set with swingarm mount kit includes streamline style mini footboards.A Wyatt Gatling patch is included in the kit. Installation will require re-installation of the original...

Chrome swingarm mount kit includes right & left side chrome pivot caps, passenger footboard mounts and passenger footboard with rubber pads.Installation will require re-installation of the original...

Chrome rear frame bar set. Top of the bar is angled downward to allow for more passenger leg room.*WARNING: This frame bar may provide limited leg and cosmetic vehicle protection under unique...

Profile frame bar set features left and right sides with 7/8" chrome plated tubing. For use with stock type saddlebag supports.The unique shape of these guards gives the passenger more leg room. Not...

Raw steel hardtail rear frame section has replica forged axle plates for the exact look of the 1950's rigid frames. Accepts FXST oil tank, transmission mount plate and electric start.Hardtail for...

Left side caliper frame mount bracket for right side drive motorcycles must be welded on. Bracket is for rigid frames when mounting brake units. Fits:FLST 1987-1999FXST 1987-1999Additional Information

Rigid hardtail frame raw steel rear section is 1957 style replica construction with components featuring the factory details of the period.The rear transmission mounts are 2" from the bottom cross...

D+D XL raw rigid frame features a 1-1/4" thick wall, DOM steel tubing with 1-1/2" backbones, 30  rake and 0  stretch. This rigid frame is a basic starter frame.Frame will require custom 3/4" rear...

FXD raw weld on hardtail is easy to install as the alignment is accomplished in the mount design provided.Raw weld on hardtail uses a 14-1/2" rear axle, a chrome rear caliper kit and a battery box is...

Raw finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications. Swingarm is for use...