Harley Davidson

Replica rear hardtail frame section is duplicated from an original rigid frame of 1957. Left axle plates are forged steel as OE. Weld-on type. The axle slots are 7/8" on both sides.Full replica...

Chrome finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications.Lowers bike 1/2"...

Fairing outer shell is made from fiber reinforced plastic. This shell includes brass inserts to accept screws to mount to the inner fairing.This outer shell allows use of the stock hardware. ...

V-Twin - 51-0742 - M8 Engine Bar BlackDescriptionBlack engine bar mount to front frame section, bolt on design features nylon bottons on ends for protection. Acts as engine guard and highway bar for...

This raw steel full rear section hardtail for Sportsters includes the rear motor mount and 4 bolt plate mount with upper and lower tube set. Frame is used to replace the stock rear motor mount and...

Neck frame with hallmarks forged in place. Machined to accept neck lock tumbler.Milwaukee forged neck is accomplished in 4 stages: First the steel is fired as red hot ingot, next huge hammers compact...

V-Twin - 51-0673 - Frame Caliper Bracket Weld on TypeDescriptionWeld on frame caliper bracket for rigid frames when mounting brake units. Bracket is constructed of steel, featuring a bevel cut, and...

Lower frame gas tank mount set is without cross bracket. It includes the right and left tabs. Tabs are constructed of st eel and have a raw finish.May require finishing prior top installation and...

This 5th Mount transmission frame repair tab is weld on style for stock frames. The tab is constructed of steel and has a raw finish.May require finishing prior to installing. Fits:FX 1971-1984FL...

Rear pipe frame tab. Fits: FL 1958-1984 Additional Information UOM 1 - EA Manufacturer V-Twin

Brake line tee tab. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA Manufacturer

Cable mount frame tab is for under tank. Fits:FL 1955-1972Additional Information UOM1 - EA Manufacturer

Upper shock frame mounts are weld on style for stock frames.Sold as a set of two. Fits:FL 1965-1984FX 1971-1984Additional Information UOM1

Casting top seat mount is for frame seat post, frame back bone and frame upper seat rail yoke. Fits:FL 1958-1984Additional Information UOM1 - EA

Frame mount tab set for solo seats have weld on mount tabs. Use with T bar and pivot bolt to mount K and CH solos. Fits:XL 1957-1979Additional Information UOM

This weld on style coil mount frame block set repairs stock frames and has a 3/8"-24 UNF thread. Fits:FL 1956-1983FX 1971-1983Additional Information UOM<

Frame top engine mount is two halves with seat tee and rear tank mounts incorporated into the top mount. Weld in place for accurate restoration.*NOTE: Threaded for seat "T" bolt. Fits:FL...

Rigid frame front oil tank mount casting to be welded on.Thread is 5/16 x 24 and the lip from the bottom to the top measures 1-1/4". For use with 1-1/2" bar. Fits:FL 1941-1984FX 1972-1984EL...

Rear frame engine mount and front transmission mount. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA

Neck frame forging has a 30  rake with key hole. Machined to accept neck lock tumbler.Forged neck is accomplished in 4 stages: First the steel is fired as red hot ingot, next huge hammers compact and...

Neck frame casting fits XL models to be welded in place on 30  stock or custom frames. Has unmachined padlock boss. Accepts neck cup kit.Neck frame accepts stock bearing cups and trees. Fits:XL...

Big Twin neck forgings machined to accept stock diameter tubing with 30  rake.Includes key lock tab and right hand number boss forged in neck. *NOTE: This frame neck does not include Manufacturer's...

Gas tank mounting adapter kit allows 1984-1999 2 piece tanks to be mounted to 2000-up models and utilize original dash panel. Fits:FLST 2000-2017FXST 2000-2017Additional Information

Rear tank frame mount tabs. Fits:FL 1941-1984EL 1936-1947U 1937-1948Additional Information UOM1 - SET

New Old Stock" Frame gusset plate is for the left side on swingarm frames.New Old Stock from the 1980's, part has rust and oxidation! Fits:FL 1958-1968FLH 1958-1968Additional Information

Weld on frame footpeg mount without thread.Mount can be welded to 1958-1977 swingarm frames to utilize the stock FXE mount and raise the peg position. Sold as a pair. Fits:FX 1971-1978FL...

Mid control mount kit is used to mount to the two holes located in the lower frame brace. Kit features a black finish.Mount features holes on each side for the left and right foot brake peg mount...

XL control mount set features a black finish. Control mounts for right (2 bolt plate) and left (3 bolt plate) to accept Big Twin forward controls.Set is used to mount 1941-1999 Big Twin forward mount...

V-Twin - 51-0484 - XL Hardtail Axle Plate SetDescriptionRaw set of right and left axle plates for Sportster hardtails, features 7/8" slots on both sides. Fits:XL 1982-UPAdditional Information<

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

Raw steel neck lock pin only. Fits:FL 1948-1968VL 1930-1936Additional Information UOM1 - EA Manufactu

XL rear motor mount pad is the tall type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA

XL rear motor mount pad is the short type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA

Replica rear hardtail frame section is duplicated from an original rigid frame. Weld-on type and does not have seat post bushing.The rear transmission mounts are 1-1/2" tall. This hardtail includes...

10" dark smoke Batwing fairing windshield. Fits:FLHT 1996-2013FLHX 1996-2013Additional Information OEM No.58303-96

V-Twin - 51-0448 - Dark Smoke WindshieldDescription10" dark smoke Batwing fairing windshield. Fits:FLHT 2014-UPFLHX 2014-UPAdditional Information

7" dark smoked wind splitter windshield for the Batwing fairing is easy to install and gives the fairing a more stylish look while decreasing the wind noise. Constructed of Lexan material.NOTE: Does...

V-Twin - 51-0441 - Wind Splitter Dark Smoke WindshieldDescription7" dark smoke Batwing fairing wind splitter windshield.NOTE: Does not fit with windshield bags or pouches. Fits:FLHT 2014-UPFLHX...

Softail top frame plate features a raw steel finish, to match with seat area plate on 1986-1999 Softail original frames.For Hardtail installation. *NOTE: Align with the (2) 1/4" holes in plates. ...

Engine bar features 1-1/4" tubing.Warning: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide). It...