Engine

Paughco Hanger Bracket Hanger bracket used for the Paughco 1-3/4" Drag Pipe for FL Models exhaust systems.

S&S Chrome Rocker Box for Harley Evo Big Twin 1984-1999 Chrome rocker box available in billet or die-cast construction. Please be sure to check the fitment table below to ensure it will fit your bike! Details: Positive O-ring seal ensures...

S&S Cycle - Steel Rotary Breather Gear fits '84-'99 Harley Models - Big Twin Features: All-steel construction Welded-in screen Higher flow than stock Elongated breather pocket scavenge hole for increased...

S&S Cycle - Tappet Cuffs fits '06-'21 XL Models (Exc. '21 Sportster S/RH1250S) Repl. OEM #18505-06 With these cuffs, you can capture the tappets and not worry about affecting vertical motion to keep them perfectly aligned, even in high-stress, high...

S&S Pushrod Tubes - fits '17-'21 M-Eight & '99-'17 Twin Cam Features: Stylish Black pushrod tubes enhance the look of your engine Great match for the Black engine covers offered on some new HD models Pushrod Tubes only Requires separate...

S&S Quickee Pushrod Kit w/ Black Covers for Harley Twin Cam 1999-2017 Kits include four S&S Quickee pushrods, four pushrod covers, O-rings Pushrods are manufactured from chromoly steel for superior strength Pushrod covers have a gloss black...

Trask Assault Series Cam Covers - fits '01-'17 Twin Cam w/o Cam Position Sensor Available in Chrome, Gloss Black, and Raw Machined. Features: Transparent for viewing internal engine components Matches Assault series air cleaners Made in the U.S.A...

V-Twin - Black Nose Cone Cam Cover fits '73-'93 Big Twin Models OEM #25268-84A V-Twin's Nose Cone Cam Cover is designed to fit Big Twin Models. The bushings are installed and a seal is included. NOTE: This cover comes with mounting screws, a gasket and...

V-Twin - Pushrod Cover Kit fits '17 & Up M8 Models - Black V-Twin's pushrod cover kit for M8 Softail models includes a clip, a spring, a cup, an inner tub and a titanium-plated lower tube set. Fitment FLT 2017-UP

Vance & Hines O2 Sensor Port Plug Kit: Kit allows select pre-closed-loop H-D models to run newer style exhaust systems equipped with O² sensor ports Includes two zinc-plated plugs with sealing washers Simply screw into nonessential sensor...

Colony - Crankcase Oil Screen & Spring Kit fits '70-'99 Big Twin & All Aftermarket Cases (OEM #24981-70, 24982-70) Features: Tappet screen and spring Made in the USA Fitment 1999 Harley-Davidson Softail Night Train...

Rocker arm shaft end nut kit contains 4 cap nuts and washers with you choice of cadmium or chrome finish. Fits: FL 1966-1984 FX 1971-1984 FLT 1979-1983 FXR 1982-1983 XL 1957-1985

Colony - Tappet Adjuster Locknuts fits '38-'84 Big Twin (Except Evolution) & '57-'85 Sportster Models Features: Split locknuts with 9/32"-32 thread Made in the U.S.A. Fitment 1984 Harley-Davidson Electra Glide Special...

Top motor mount acorn bolts & washers.   Fits: EL 1936-1940 FL 1941-1984 FX 1971-1984

Drag Specialties - Cam Chain Tensioner Kit fits '07-'17 Twin Cam & '06 Dyna Models (Repl. OEM #S 39968-06/39969-06) Features Stock replacement hydraulic cam chain tensioners Sold as a primary/secondary 2-piece...

Drag Specialties - Cam Cover fits '73-'92 Big Twin Models The bushings on this cam cover are installed, pinned and reamed to OEM specifications. Available in your choice of a satin black or chrome finish. Features Die-cast aluminum...

Drag Specialties - Cam Cover fits '93-'99 Evolution Big Twin Models The bushings on this cam cover are installed, pinned and reamed to OEM specifications. Available in your choice of a satin black or chrome finish. Features Die-cast aluminum...

Drag Specialties Front Motor Mount Plate This motor mount by Drag Specialties is for 1999-2006 FLT 5-speed models, and is made to replace OEM part number 47159-79T. Features: Made of heavy-duty chromed steel to OEM...

Drag Specialties - High-Performance Oil Pump fits '17-Up M8 Twin-Cooled Motors The High-Performance Oil Pump features high-quality die-cast aluminum body construction, and high-strength steel gear construction. Features Helps to reduce oil...

Drag Specialties - High-Performance Twin Cam Oil Pump Fits '07-'17 Twin Cam & '06 Dyna Models This pump helps to decrease oil carryover during high rpm operation; the higher volume helps to lower engine and oil temperatures. There is a gain of 16%...

Drag Specialties - Oil Pressure Sensor fits '99-'16 Touring Models (OEM #74438-99A) Features: Accurate reproduction of the OEM sending unit Precision calibrated Fitment 2015-2016 Harley-Davidson Road Glide Special...

Drag Specialties - Rear Master Cylinder Cover fits M8 Softail Models

Drag Specialties - Spin-On Drop-In Oil Filter Element fits '36-'84 Big Twin Models (Repl. OEM #63840-48A) This is a high-quality drop-in oil filter element. Fitment 1984 Harley-Davidson Electra Glide Special...

Drag Specialties Exhaust Heat Wrap Fiberglass cloth rated at 1200°F continuous/2000°F intermittent Perfect for wrapping pipes or mufflers Keeps the heat inside Comes in 1" or 2" wide x 25' rolls Includes four 14" ball bearing and barb...

Feuling - 12-Point Engine Fastener Cam/Pinion Shaft Bolt Kit fits '99-'17 Twin Cam Models This kit comes with bolts, hardened washers and a camshaft retaining ring (black oxide). The tensile strength of this kit is rated at 170,000 psi (EU: 1172,11...

Feuling - 12-Point External Engine Bolt Fastener Kit fits '04-'17 Sportster Models The 12-Point External Engine Bolt Fastener Kit allows you to secure your engine with complete confidence. The kit comes with the following hardware: right side cover,...

Feuling - 543 Series HP+® Chain Drive Camchest Kit fits '07-'17 Twin Cam & '06 Dyna Glide Models Features: All necessary components from top-to-bottom of the camchest Provide maximum reliability, longevity, peak performance, and the coolest...

Feuling - Endurance Beehive® Standard 6mm Valve Stem Valve Springs with Factory Retainers Fits Harley '17-Up M8 Models Features Made from premium stress-relieved conical ovate wire Feature extremely high-level of fatigue life Use a much smaller...

Feuling - Headbolt Kit fits '99-'17 Twin Cam and '92-'22 Sportster Models (exc. '21-'22 Sportster S/RH1250S, 22 Nightster/RH975) This kit features wide underhead flange bolts and hardened chamfered washers that provide even load distribution for the...

Feuling - Outer Camshaft Bearing Kit Fits '99-'06 Big Twin Models (Exc. '06 Dyna Models) W/ Chain Drive Features Kit includes one ball bearing front cam bearing and one roller bearing rear cam bearing with...

Hard Drive - 5.5" and 3.25" Universal Exhaust Hanger Bracket Set Features Sturdy for years of use Chrome finish  

Helix Racing Fiberglass Exhaust Wrap  

Jagg - Vertical Frame Mount 6-Row Oil Cooler System Jagg's Vertical Frame Mount 6-Row Oil Cooler System is a must-have performance part for Harley owners. This cooler mounts to the left frame down-tube, spaced away from the frame to deliver airflow to...

James Gaskets Gasket Kits use state of the art materials and production methods to make the best gaskets available. Made in the USA Fitment: '70-'92 FLT, FXR, Softail

James Gaskets - Complete Gasket Set fits '66-'84 Shovelhead 4-Speed; Repl. OEM #17029-70/17029-66 This top-quality complete gasket set comes with the gaskets, oil seals and O-rings required to completely rebuild '66-'84 Shovelhead 4-Speed . Made in...

The James Gaskets Gasket Kit, Tappet Cover Pushrod Tube: State of the art material Made in the USA Includes Mounting Hardware Fitment: '99-Up Twin Cam Models

James Gaskets Twin Cam Gasket Kits uses state of the art materials and production methods to make the best gaskets available. Made in the USA Fitment:  '99-Up Twin Cam Models

Paughco 1-3/4" Mounting Clamp Mounting clamp required to install 1800-1867 (Paughco 1-3/4" Drag Pipes for FL Models, 34" pipes).

Paughco Drag Pipes Fits Harley 70-84 FX Models w/ Swingarm Frame Required brackets and optional heat shields: 1860-0233 - Required hanger bracket DS-209923 - Muffler Support, right side, chrome 1861-1039 - Front heat shield 1861-1038 - Rear heat...

Paughco Floorboard Adapter for FL Drag Pipes This floorboard adapter is made to be used with the Paughco 1-3/4" Drag Pipes for FL Models (DBC-2619).