Jims

V-Twin - 16-1179 - Jims Ignition Switch and Fork Lock ToolDescriptionUsed to make installing or removing the ignition switch and fork lock a easy process.Locates on the ignition switch face nut that...

V-Twin - 16-1178 - Jims Seat Mounting Screw ToolDescriptionThis tool is used to mount the FXST seats to the rear fender and eliminates using a flat head screw driver and damaging the fender paint...

V-Twin - 16-1171 - Jims Compression Release ValveDescriptionThis valve is used with Jims compression release valve tool. Release valve will make starting your engine effortless.Set of two. Drill and...

V-Twin - 16-1169 - Jims Compression Release Valve ToolDescriptionUse this tool for machining all Twin Cam heads for compression releases. Installs easily on front or rear head, with or without valves...

V-Twin - 16-1164 - Piston Pin Support PlateDescriptionThe Jims piston support plate provides a non-marring flat support to push the bottom of the piston as rings and cylinder are installed over...

V-Twin - 16-1163 - Balancer Shaft Retention Pin for TC-88DescriptionUse the balancer shaft retention pin tool secures the engine balancers on TC-88B engines when servicing flywheel assembl y. This...

V-Twin - 16-1134 - Jims Rolling Buddy Engine Dummy PlateDescriptionJims rolling buddy engine dummy plate is to be used on all rubber mount Big Twins.This tool will allow chassis to be moved once the...

V-Twin - 16-1079 - Jims M8 Oil Pump Alignment ToolDescriptionJims oil pump alignment tool is the perfect aid for the technician to either assemble as individual components with supplied studs or as...

V-Twin - 16-1061 - Jims Castle Nut SocketDescriptionJims castle nut socket is for use with FXST inverted forks.2017-up Softail models requires the castle nut to secure and compress the fork spring...

V-Twin - 16-1054 - Jims Alternator Rotor Puller Big TwinDescriptionOur Big Twin alternator rotor puller uses the sprocket shaft end to center the two threaded holes in the rotor to allow its safe...

V-Twin - 16-1051 - Jims TC-88 Connecting Bushing ToolDescriptionTo remove and replace wrist pin bushing without removing connecting rods from crankcase, use the Jims TC-88 connector rod bushing tool...

V-Twin - 16-1045 - Jims Magnetic Tappet Holder Tool SetDescriptionJims magnetic tappet holder tool set holds the tappets up while changing cams, cam support plate or oil pump on all TC-88 and M8...

V-Twin - 16-1031 - Jims Tappet Position Holding ToolDescriptionJims tappet position holding tool for Twin Cam and Sportster engines. This tool allows the tappets and anti-rotation pins to be safely...

V-Twin - 16-1030 - Jims Clutch Adjusting ToolDescriptionJims clutch adjusting tool for use on Big Twins 1985-up allows the mechanic to quickly and accurately tighten the clutch adjusting screw jam...

V-Twin - 16-1029 - Jims Transmission Assembly Vise Stand ToolDescriptionJims transmission assembly vise stand tool is used to assist in the assembly of the transmission gears and shafts.This tool...

V-Twin - 16-1028 - Jims Main Drive Gear Case Seal Installer toolDescriptionJims main drive gear case seal installer tool ensures correct alignment and installs seal to the correct depth without...

V-Twin - 16-1027 - Inner Primary Cover Bearing and Seal Remover Installer ToolDescriptionThis tool safely removes and installs the inner primary bearing without damage to the new bearing.Also removes...

V-Twin - 16-1009 - Fork Spring Compressor ToolDescriptionOur Jims fork spring compressor tool puts pressure on top fork plug to compress spring to ease in assembly.Compressor can be mounted in a vise...

V-Twin - 16-1008 - Fork Tube Plug ToolDescriptionThis Jims fork tube plug tool is used to remove and install top fork tube plugs. Eliminates possible burring of plug, caused by wrenches. Fits:FLST...

V-Twin - 16-0994 - 5-Speed Main Drive Gear InstallerDescriptionJims 5-speed main drive gear tool is used to remove and install the main drive gear. It also installs the main beari ng without removing...

V-Twin - 16-0893 - Case Lap HeadDescriptionCase lap head only has an outer diameter of 1-3/4". Fits:All modelsAdditional Information UOM1 - EA ManufacturerJims OriginUSA 2025 Catalog Pages1276

V-Twin - 16-0889 - Oil Pump Snap Ring InstallerDescriptionThe oil pump snap ring installer makes it easy to install outer snap ring on oil pump shafts without stretching the ring. Use on Big Twin oil...

V-Twin - 16-0888 - Sprocket Shaft Seal and Lock InstallerDescriptionSprocket shaft seal wrench tool installs and removes bearing nut on Big Twin models. Fits:FL 1955-1969Additional Information OEM...

V-Twin - 16-0877 - Jims Mainshaft Bearing Race ToolDescriptionThis mainshaft primary bearing race remover and installer is used on all 1984-up Big Twins Fits:FXD 1991-2005FLST 1986-2006FLT...

V-Twin - 16-0793 - Cam Chain Unloader ToolDescriptionCam chain unloader tool will hold the tension of the primary cam chain on the TC-88 model engine. Instructions included. Fits:FLT 1999-2016FLST...

V-Twin - 16-0792 - Jims Cam Shaft Remover and Installer ToolDescriptionJims cam shaft remover and installer tool allows removal and installation of cams in the TC-88 model engine.Tool is used in...

V-Twin - 16-0791 - Jims Bushing Remover/Installer ToolDescriptionJims bushing remover/installer tool will help remove and install bushings in cam support plate on TC-88 models. Fits:FLT 1999-2016FLST...

V-Twin - 16-0790 - Jims Cam Locking Wedge ToolDescriptionJims cam locking wedge tool will lock the gear teeth on the TC-88 model engine. Instructions included. Fits:FLT 1999-2016FLST 1999-2017FXST...

V-Twin - 16-0740 - Jims Clutch Gear Puller ToolDescriptionJims 4 speed clutch gear puller tool is designed to remove the starter clutch gear without damage to the gear or shaft. Fits:UL 1937-1948FX...

V-Twin - 16-0731 - Jims Transmission Door Installer ToolDescriptionJims transmission door installer tool allows installation of transmission shafts without the use of a hydraulic or arbor press...

V-Twin - 16-0727 - Jims Wrist Pin Bushing Reamer ToolDescriptionJims wrist pin bushing reamer tool is easy to use with their design lead in taper at the start of each ream.Reamer is made to exact...

V-Twin - 16-0719 - Transmission Stud Installer ToolDescriptionJims transmission stud installer tool is used on stock and aftermarket transmissions that use bottom mouting studs. Fits:UL 1937-1948FLST...

V-Twin - 16-0705 - Snap Ring Remover ToolDescriptionSnap ring remover tool will remove the Timken bearing outer race snap ring without damage to the case.You can replace the snap ring in Big Twin...

V-Twin - 16-0700 - Jims Seal ToolDescriptionJims seal tool is used to install the main seal in transmission. Tool will press in the seal as flat and straig ht as possible. Fits:FXD 1991-2005FLST...

V-Twin - 16-0695 - Jims Breather Ream ToolDescriptionJims breather ream tool repairs damaged breather gear holes.Using this tool will repair damaged breather hole, to use a .030 oversize breather...

V-Twin - 16-0682 - Jims Primary Locking Bar ToolDescriptionJims primary locking bar tool is used to lock the primary for service work on 883 XL models. Fits:XL 1991-2003Additional Information UOM1 -...

V-Twin - 16-0681 - Jims Primary Locking Bar ToolDescriptionJims primary locking bar tool is used to lock the primary for service work on FXR, FLT and FLHT models. Fits:FXR 1982-1994FLT...

V-Twin - 16-0680 - Jims Primary Locking Bar ToolDescriptionJims primary locking bar tool uses to lock the primary for service work on FXD, FL and FXST models. Fits:FXST 1984-2006FX 1971-1984FL...

V-Twin - 16-0679 - Evolution Head Bolt Torque Gauge ToolDescriptionThis accurate gauge allows the measuring of 90  when tightening head bolts. Also features torquing sequence lasered on gauge...

V-Twin - 16-0672 - Jims Transmission Cover Bearing ToolDescriptionJims transmission cover bearing tool removes and installs bearings on 5-speed and aftermarket 6-speed transmissions. Fits:FXD...