Tools

Lang Tools - 446 - Cylinder Sleeve Hold-DownFeaturesSpecialty nuts are used to hold down cylinder sleeves during serviceAllow motor to be turned over with heads offSpecsApplicationCylinderProduct NameNutTypeCylinder Sleeve HolderColor/FinishSilverUnits4...

Lang Tools - 437 - Crank Bearing Tool - Harley-Davidson®FeaturesDiameter of the bolt is turned slightly smaller than the actual crankshaft diameter, allowing the inner bearing races to be installed and removed without pressing them on or offAllows much...

Lang Tools - 5530 - Wrench - Intake Manifold - Ratcheting/Reversible - Harley-Davidson®FeaturesFeatures reversible ratcheting action and an 1/4" ball-end Allen bit end for flexibility in tight areasTo install and remove intake manifold socket-head cap...

Lang Tools - 3497 - Plier Snap Ring Set - 6-PieceFeaturesIncludes most popular sizes in straight, offset and 90 Internal/external fixed-tip pliersPacked in blow-molded caseMade in the U.S.A.LANG 3497 - 6-Pc Fixed Tip Convertible Retaining Ring PliersLANG...

Lang Tools - 9636 - Rear Axle Nut WrenchFeaturesReversible ratcheting wrench used to install and remove 36 mm axle nutsLow profile wheel allows access to the nut without removal of the exhaust1/2"- square drive hole allows a torque wrench to be used when...

Jims - 727K - Valves - Compression ReleaseFeaturesSimply drill and tap (10 mm x 1.0 mm) each cylinder head and thread in the self-sealing release valvesGive your starter a hand by installing these in your high-compression, big-inch motorFits all Big Twin...

Hot Cams - CIK-001 - Installation KitFeaturesContains degree wheel, standard unit indicator, adjustable magnetic stand, and three positive stops (10 mm, 12 mm and 14 mm threads)Can be used to install and adjust timing of any camWooden carrying...

Fuel-Tool - MC800 - Gauge - Fuel Pressure - Magnetic - 360 FeaturesGauge attaches magnetically to machine's fuel tank to quickly check both Static (idling) and Load (under acceleration) fuel pressure readingsUsed to diagnose loss of power, poor fuel...

Fuel-Tool - MC400 - Rebuild Kit Installation Tool - Fuel Check ValveFeaturesMSDS Migration DataProvides for fast and easy professional installation of check valve O-ring or Rebuild kit without having to remove tank from the bikeThe industry's first and...

Helix - 350-3915 - Tester - Fuel - EthanolFeaturesMeasures the percentage of alcohol/ethanol contained in your fuelDoubles as a Phillips and standard screwdriverComes in a reusable storage tubeSpecsRiding StyleOff-RoadRiding...

Fuel-Tool - MC100 - Fuel Transfer System - Delphi Fuel InjectionFeaturesMSDS Migration DataTransfers up to one quart of fuel every 20 seconds; will not stall engine while in useSmall and compact size, stores anywhere; storage pouch includedSimple and...

Fuel-Tool - MC500 - Gauge - Fuel Pressure/Delphi Fuel Injection - 100 psiFeaturesMSDS Migration DataIncludes a solid brass adapter and release valve, steel housing (100 psi) gauge, stainless steel springs, Viton O-rings, O-ring lubricant and nylon...

Jims - 742K - Hardware Organizer - SetFeaturesSpecific stands for top end, transmission, cam chest, and primaryPart organizers for powertrain assembly, teardown and storageStands nest to save spaceMade in the U.S.A.SpecsColor/FinishBlueProduct...

K&L Supply - 35-8434 - Magnetic Base - Flex ShaftFeaturesFlexible indicator mounting arm locks into place to make any job easyFeatures an easy-to-use on/off knobFor use with dial indicator gaugeSpecsApplicationDial IndicatorRiding...

K&L Supply - 35-8421 - Dial Indicator - Magnetic BaseFeaturesReads 1.0" in increments of .001"Gauge can be locked for a zero settingIncludes magnetic base stand that has an adjustable dial indicator mounting arm for a wide range of...

K&L Supply - 35-9016 - Tool Tire Bead StarterFeaturesEasy to use: Just mount tire to wheel, position bead starter, then cinch down with ratchet lever; add air until bead begins to engage, then slowly ease belt tension as more air is addedAll-in-one...

Jims - 752 - Remote Starter ToolFeaturesIncludes 4' lead cable with alligator clip for start positive post terminal and motor post negative hookupsHandy for tappet adjustments, servicing and diagnosing starting and electrical issuesActivates starter and...

Jims - 935 - Inspection Cutter Tool - Oil FilterFeaturesUse to inspect oil filter for any damaging particles that may be trapped in filterLocks down filter for a clean cut around filter baseFits filters up to 5-1/2" diameterMade in the U.S.A...

Jims - 5504 - Tappet Position HolderFeaturesTappet locations are clearly referenced on the tool, which also serves to protect the tappets from damage when removed from the engineSafely stores anti-rotation pins and tappets for proper and accurate...

Feuling Parts - 9008 - Reamer Tool - Camplate/Oil Pump - Twin Cam/M8FeaturesTo use, lightly machine (clean) the camplate relief valve seat and re-seat the plunger valveBest used in conjunction with Feuling pressure test tool part# 9010 or 9006, but can...

Jims - 765 - Pump/Test Stand - Hydraulic Tappet - Big TwinsFeaturesHelps diagnose loose or spongy tappets that could eventually lead to bleed-down issues or sticky tappets that won't pump up due to poor hydraulic unit fitmentAllows filling of hydraulic...

K&L Supply - 35-8621 - Stand - Wheel Truing/BalancingFeaturesWheels mount to adjustable center cones or ball bearings for trueing and static balancingAdjustable frame rails accommodate wide rims and wheelsBalances and trues all 14" to 21" motorcycle...

K&L Supply - 35-3498 - Carburetor Cleaner Wire SetFeatures14-piece wire set with spiral knurling for cleaning popular sized jets and carb body holesSpecsRiding StyleOff-RoadRiding StyleWatercraftProduct NameCleanerStyleSpiral...

Dennis Stubblefield Sales - TOOL-B - Locking Tool - Crankshaft - Harley DavidsonFeaturesEnables timing and camshaft work to be done without the crankshaft moving from the timing mark lineLocks the crankshaft through the timing mark hole on the leftMade...

Dennis Stubblefield Sales - TOOL-A - Locking Tool - Ignition Points - Harley DavidsonFeaturesLocks ignition points to advanced position during tune-ups and distributor workFits most Big Twin Classics and '70-'78 models with ignition points systemsMade in...

Did - KM500R - Chain Tool - Chain Breaker/Riveting/Press-FitFeaturesDID logoDesigned to cut chain, press fit connecting link plates, and rivet pin heads with one easy-to-use toolMay be used to cut any 520, 525, 50 (530) or 532 chainSmall compact design;...

Cruztools - SPAN1 - Spanner Wrench - Shock - Pre-Load AdjusterFeaturesMade of tough stainless steel and is compact enough to bring in your tool kitPerfect tool for adjusting pre-load on a shockMade in the U.S.A.SpecsMaterialStainless SteelTypePre-Load...

Andrews - 212116 - Gauge Pin - Cam Drive Gear - 0.108"FeaturesUsed to measure the outside diameter of cam drive gearsMade in the USAThere are two basic differences between '90-'99 cam gear sizes and earlier years. The overall range of gear pin...

Andrews - 212105 - Gauge Pin - Cam Drive Gear 0.105"FeaturesUsed to measure the outside diameter of cam drive gearsMade in the USAThere are two basic differences between '90-'99 cam gear sizes and earlier years. The overall range of gear pin measurements...

Belt Drives Ltd. - CLT-100 - Clutch Lock Up ToolFeaturesDesigned to help properly torque the clutch basket and hub assembly to the mainshaft of the transmissionNo need to use an impact wrench that can damage the basket, hub or other componentsFor use on...

Barnett - 638-30-80001 - Lock Plate - Clutch Basket - Scorpion - Set 4FeaturesSpecifically designed to be used to lock outer clutch basket to inner hub for removal and installationMade in the USASpecsUnitsSet of...

Belt Drives Ltd. - RGLT-100 - Ring Gear Lock ToolFeaturesChoose the appropriate side of the tool for kit; one side is for open belt drives up to 06 models and the smaller, reverse side is for open belt drive kits for 07-16 modelsFor use on all Belt Drive...

Barnett - 638-30-70001 - Scorpion Hub PullerFeaturesUsed most Scorpion clutchesMade in the U.S.A.SpecsColor/FinishAnodizedMaterialSteelTypeClutch AdjustmentModelScorpionColor/FinishOrangeUnitsEachProduct NameHub PullerApplicationClutchMaterialBillet...

Lang Tools - 492 - Fuel Tank Lock Ring ToolFeaturesRemove and install the lock ring on fuel tanksAllows access to the fuel filter and pumpSpecsRiding StyleStreetUnitsEachMaterialAcrylonitrile Butadiene Styrene PlasticApplicationFuel...

Lang Tools - 9280 - Wrench - Crankshaft - 24-Tooth - Ratcheting - Big TwinFeaturesUsed for rotation of the crankshaft on all 24-spline engines and to check engine timing and parts clearanceErgonomic E-Z Grip handle allows more turning power with less...

Lang Tools - 6531 - Wrench - Lower Rocker Box - Ratcheting - 1-1/4" Socket Length - EvolutionFeaturesVinyl grip provides a comfortable, ergonomic grip and prevents the wrench from scratching or marring the bikeExtra-long reversible ratcheting wrench is...

Lang Tools - 6530 - Wrench - Lower Rocker Box - Ratcheting - 1" Socket Length - Twin CamFeaturesVinyl grip provides a comfortable, ergonomic grip and prevents the wrench from scratching or marring the bikeExtra-long reversible ratcheting wrench is used...

Lang Tools - 9794 - Wrench - Crankshaft - 10 Spline - RatchetingFeaturesUsed for rotation of the crankshaft/check engine timing and parts clearance on Sportster® motorcyclesEZ Grip screwdriver-style handle for comfort and more turning powerOffset design...

Lang Tools - 6562 - Wrench - Rear Fender - FLFeaturesExtra long rocker box wrench with T40 bit used to remove/replace the bolt that holds the rear fender to the frame on H-D touring modelsRemoves the rear fender bolt without having to remove the tireMade...

Lang Tools - 6538 - Wrench - Exhaust BracketFeaturesLow-profile design allows for easy access to the exhaust bracket in between the frame and engineVinyl grip protects bike from damage during use and provides an ergonomic gripTo remove and install the...