Touring Electra Glide Highway King FLHFB

Battery tray carrier bracket has a bright chrome finish. Fits:FL 1965-1984Additional Information OEM No.66212-65

Chrome side mount tail lamp bracket will mount vertical flat side unit to FXD primary. Fits:FL 1965-1984FX 1965-1984FXST 1984-1988Additional Information

Zinc plated top motor mount is without the choke mount. Fits:FL 1948-1984Additional Information OEM No.16852-67

Top engine mount replaces stock type and features a raw finish.. Fits:FL 1948-1965Additional Information OEM No.16853-48

Regulator mount bracket attaches to engine mount and is made of steel with a chrome finish. Fits:FXST 1984-1999FLST 1986-1999FX 1971-1984FL 1941-1984Additional Information

Top motor mount chrome is without the coil mount holes. This engine mount is for Panhead and Shovelhead engines. Fits:FX 1971-1984FL 1948-1984Additional Information

Front engine mount block threads into regulator mount block.This chrome mount block acts as a nut for the front bolts and will mount the regulator. Sold in a quantity of 2. Fits:FXST 1984-1999FLST...

Dual exhaust clamp set is for FLH models.Order pipe support bracket for 1958-1984 applications separately. Fits:FL 1966-1969Additional Information UOM<

Universal front solo seat mount includes mount and tilt up seat bracket for solo seats. Lower bracket is direct bolt onto FLH frames.The spacing between the hinge lugs measure 1-5/8". The stud thread...

Replica cadmium seat post and T kit includes fully assembled heavy duty cadmium plated post with a forged steel seat T, and related hardware.*Note: UPS may consider this part as packaged "oversize"...

Replica black seat post and T kit includes fully assembled post and forged steel seat T with related hardware.*Note: UPS may consider this part as packaged "oversize" for shipment, as compared to the...

Replica chrome seat post and T kit includes fully assembled post and forged steel T and related hardware.Stock seat T will work for mounting buddy seats with the use of #31-0177 Front Nose Bracket. ...

Police type solo seat mount kit includes nose bracket, 2" hair pin springs and rear mount. Fits:FX 1971-1984FL 1958-1984Additional Information UOM

Regulator rectifier mount is for a 12 volt Bosch generator and has a chrome finish. Fits:XL 1958-1978FL 1958-1969Additional Information UOM1 - E

Police type solo seat mount kit includes nose bracket, 2" chrome coil springs and rear mount. Fits:FX 1971-1984FL 1958-1984Additional Information UOM

Ignition coil strap has a black finish. Fits:FX 1971-1977FL 1965-1977Additional Information OEM No.31727-65

Chrome Horn mount bracket. Fits:FLH 1968-1984FL 1968-1984Additional Information OEM No.69131-68 UOM

Replica chrome seat tee includes 2 stage front bushing and 3/8" bolt.NOTE: 2-stage steel bushings are removable and can be interchanged or replaced as necessary. Fits:FL 1965-1980G...

Solo seat T will mount police and buddy seats to all big twins with seat posts. Fabricated from square solid steel and features a black finish. Does not include bushing.Front spool has 3/8" hole for...

V-Twin - Chrome Replica Seat Handrail fits '49-'52 WL, '49-'73 FL Models (OEM #91575-49) Replica chrome handrail is for buddy seats and police solos. Handrail is a direct mount on buddy seats. It is...

Front motor mount frame spacer will allow installation of a Knucklehead or Flathead engine in a 1948-1984 frame.The mount holes measure 3-1/4" center-to-center. *NOTE: The...

Ignition coil strap has a chrome finish. Fits:FX 1971-1977FL 1965-1977Additional Information OEM No.31727-72

Replica black seat T includes 2 stage front bushing and 3/8" bolt.NOTE: 2-stage steel bushings are removable and can be interchanged or replaced as necessary. Fits:FL 1965-1980G 1965-1972Additional...

Stanchion only is black for Big Twin models.These are only the stanchions from our turn signal mounting kit used for mounting the turn signals below the spotlamp unit. These do no include clamps...

Trumpet horn mount bracket for Shovelhead models. Fits:FL 1966-1984 ShovelheadAdditional Information UOM1 - EA

Timer cable to frame clamp. Fits:FL 1946-1969Additional Information UOM1 - EA ManufacturerV-Twin

Stanchion only is chrome for Big Twin models.These are only the stanchions from our turn signal mounting kit used for mounting the turn signals below the spotlamp unit. These do not include clamps. ...

Chrome front exhaust clamp set is for two into one single exhaust.Sold in a quantity of 2. Order bolt sets separately. Fits:FL 1941-1969EL 1936-1940Additional Information

Ignition coil mount plate will fit when using early coil for 1948-1973 applications. Fits:EL 1948-1952 Two way radioFL 1948-1973 Two way radioUL 1948-1948WL 1948-1952G 1948-1954 Servi-car two way...

Solid State regulator mount bolts directly to 2-brush generator housings on Big Twin and Sportster models.Regulator mount fits Accel and V-Twin finned type regulators. Fits:XL 1958-1978FL...

Chrome steel 90  bend type turn signal mount set is used for front or rear application.Sold in a quantity of 2. Fits:FL 1963-1984Additional Information OEM

Cable guide clip. Fits:FL 1966-1984Additional Information OEM No.45092-66 UOM5 - PK

Battery tray carrier bracket has a chrome finish. Fits:FL 1965-1984Additional Information OEM No.66212-65 UOM<

Chrome one piece bracket is for mounting spotlamps.The length between the mounting holes measures 13". Fits:FLH 1949-1984Additional Information OEM No.

Chrome bracket set is for front fork triple tree mounting. Set includes right and left sides.The bracket measures 1-1/2" center to center between the two top holes and 6-1/2" between the top and...

Turn signal chrome mounting kit has clamp and mounting bolt included. Kit is necessary for mounting the turn signals below spotlamp unit. Fits:FL 1968-1984Additional Information

Chrome steel flat type mount set for front or rear turn signal.Sold in a quantity of 2. Fits:FL 1963-1984Additional Information OEM No.68527-63

Polished 9" long mount bar for rear turn signals.The distance between the mount holes, center-to-center is 5-3/16". Fits:FL 1963-1973Additional Information

V-Twin - Zinc Plated Buddy Seat Nose Bracket fits '58-'84 FL Model Front nose seat bracket is used to mount buddy seats to mount systems and features a zinc plated finish. Fitment: FL 1958-1984

Zinc regulator mount bracket attaches to engine mount. Fits:FXST 1984-1999FLST 1986-1999FX 1971-1984FL 1941-1984Additional Information